Searched full:deasserted (Results 1 – 25 of 123) sorted by relevance
12345
| /Linux-v6.6/include/dt-bindings/input/ |
| D | gpio-keys.h | 9 #define EV_ACT_ANY 0x00 /* asserted or deasserted */
11 #define EV_ACT_DEASSERTED 0x02 /* deasserted */
|
| /Linux-v6.6/Documentation/devicetree/bindings/input/ |
| D | gpio-keys.yaml | 72 deasserted, or both. This property is only valid for keys that wake up the
77 EV_ACT_ANY - both asserted and deasserted
79 EV_ACT_DEASSERTED - deasserted
|
| /Linux-v6.6/sound/soc/tegra/ |
| D | tegra20_spdif.h | 127 * deasserted when either,
136 * This bit is deasserted when the end of a frame is reached after
137 * TX_EN is deasserted.
145 * This bit is deasserted when either,
146 * (a) the end of a frame is reached after TX_EN is deasserted, or
155 * (a) the end of a frame is reached after TX_EN is deasserted, or
|
| /Linux-v6.6/arch/arm/mach-omap2/ |
| D | prm2xxx_3xxx.c | 47 * reset line to be asserted / deasserted in order to fully enable the
67 * @st_shift: register bit shift for the status of the deasserted submodule
74 * reset line to be asserted / deasserted in order to fully enable the
|
| D | prminst44xx.c | 117 * reset line to be asserted / deasserted in order to fully enable the
144 * reset line to be asserted / deasserted in order to fully enable the
|
| D | cm2xxx.h | 37 /* CM_IDLEST bit field values to indicate deasserted IdleReq */
|
| D | cm3xxx.h | 61 /* CM_IDLEST bit field values to indicate deasserted IdleReq */
|
| /Linux-v6.6/Documentation/driver-api/ |
| D | reset.rst | 89 deassert causes the reset line to be deasserted immediately.
102 may be kept deasserted at all times.
104 consumer has requested it to be deasserted.
|
| /Linux-v6.6/Documentation/devicetree/bindings/sound/ |
| D | st,sta32x.txt | 10 deasserted before communication to the codec starts.
13 it will be deasserted before communication to the codec
|
| D | st,sta350.txt | 10 deasserted before communication to the codec starts.
13 it will be deasserted before communication to the codec
|
| D | cs4270.txt | 14 deasserted before communication to the codec starts.
|
| D | ak4104.txt | 16 deasserted before communication to the device starts.
|
| D | ak5386.txt | 12 If specified, it will be deasserted at probe time.
|
| D | cs4265.txt | 16 deasserted before communication to the codec starts.
|
| /Linux-v6.6/drivers/reset/ |
| D | reset-ti-sci.c | 54 * @assert argument is true, or deasserted if @assert argument is false.
115 * @id: ID of the reset to be deasserted
141 * Return: 0 if reset is deasserted, or a non-zero value if reset is asserted
|
| D | core.c | 37 * @deassert_count: Number of times this reset line has been deasserted
432 * still be deasserted, as long as other users keep it so.
495 * If an assertion fails, already asserted resets are deasserted again.
523 * After calling this function, the reset is guaranteed to be deasserted.
558 * case, the reset lines are deasserted by default. If that is not the in reset_control_deassert()
575 * If a deassertion fails, already deasserted resets are asserted again.
1221 * that just have to be asserted or deasserted, without any
|
| D | reset-ti-syscon.c | 90 * @id: ID of reset to be deasserted
126 * Return: 0 if reset is deasserted, true if reset is asserted, else a
|
| D | Kconfig | 220 that can be asserted and deasserted by toggling bits in a contiguous,
245 The reset lines that can be asserted and deasserted by toggling bits
|
| /Linux-v6.6/drivers/clk/baikal-t1/ |
| D | ccu-rst.c | 67 * domain reset (it's self-deasserted reset control).
85 * sefl-deasserted reset control, which can be activated via the corresponding
|
| D | ccu-rst.h | 18 * @CCU_RST_TRIG: Self-deasserted reset signal.
|
| D | Kconfig | 49 self-deasserted reset controls but there are several lines which
|
| /Linux-v6.6/drivers/spi/ |
| D | spi-bcm2835aux.c | 458 * * cs_change: cs is deasserted after each spi_transfer in bcm2835aux_spi_setup()
459 * * cs_delay_usec: cs is always deasserted one SCK cycle in bcm2835aux_spi_setup()
495 * * cs_change: cs is deasserted after each spi_transfer in bcm2835aux_spi_probe()
496 * * cs_delay_usec: cs is always deasserted one SCK cycle after in bcm2835aux_spi_probe()
|
| /Linux-v6.6/drivers/net/ethernet/broadcom/bnx2x/ |
| D | bnx2x_reg.h | 178 acknowledge output is deasserted; all other signals are treated as usual;
182 disregarded; valid is deasserted; all other signals are treated as usual;
204 disregarded; valid is deasserted; all other signals are treated as usual;
208 disregarded; valid is deasserted; all other signals are treated as usual;
212 disregarded; valid output is deasserted; all other signals are treated as
220 disregarded; valid output is deasserted; all other signals are treated as
240 acknowledge output is deasserted; all other signals are treated as usual;
256 acknowledge output is deasserted; all other signals are treated as usual;
308 acknowledge output is deasserted; all other signals are treated as usual;
333 disregarded; acknowledge output is deasserted; all other signals are
[all …]
|
| /Linux-v6.6/Documentation/devicetree/bindings/mmc/ |
| D | mmc-pwrseq-emmc.yaml | 31 and then deasserted to perform eMMC card reset. To perform
|
| /Linux-v6.6/drivers/reset/starfive/ |
| D | reset-starfive-jh7100.c | 29 * register means the line is asserted and a 1 means it's deasserted. A few
|
12345
