| /Linux-v5.10/include/linux/ |
| D | entry-common.h | 77 * @regs: Pointer to currents pt_regs
94 * @regs: Pointer to currents pt_regs
114 * @regs: Pointer to currents pt_regs
131 * @regs: Pointer to currents pt_regs
156 * @regs: Pointer to currents pt_regs
206 * @regs: Pointer to currents pt_regs
226 * @regs: Pointer to currents pt_regs
263 * @regs: Pointer to currents pt_regs
271 * @regs: Pointer to currents pt_regs
290 * @regs: Pointer to currents pt_regs
[all …]
|
| D | power_supply.h | 22 * All voltages, currents, charges, energies, time and temperatures in uV,
|
| /Linux-v5.10/Documentation/devicetree/bindings/iio/adc/ |
| D | adi,ad7192.yaml | 74 adi,burnout-currents-enable:
77 path are enabled. When BURN = 0, the burnout currents are disabled.
78 The burnout currents can be enabled only when the buffer is active
121 adi,burnout-currents-enable;
|
| /Linux-v5.10/Documentation/hwmon/ |
| D | tmp513.rst | 56 The driver exports the shunt currents values via the following sysFs files:
84 The bus power and bus currents range and resolution depends on the calibration
|
| D | vexpress.rst | 32 providing information about power lines voltages and currents, board
|
| D | adm1275.rst | 82 or current scaling. Reported voltages, currents, and power are raw measurements,
|
| D | k10temp.rst | 149 / LSB. The real current is board specific. Reported currents should be seen
|
| D | sysfs-interface.rst | 618 Currents section in Naming and data format standards for sysfs files
709 Also see the Alarms section for status flags associated with currents.
|
| /Linux-v5.10/Documentation/devicetree/bindings/power/supply/ |
| D | axp20x_battery.txt | 12 currents of the battery by reading ADC channels from the ADC.
|
| /Linux-v5.10/include/linux/power/ |
| D | bq2415x_charger.h | 13 * voltages and currents which can be also later configured via sysfs. If
|
| /Linux-v5.10/Documentation/devicetree/bindings/leds/ |
| D | leds-pm8058.txt | 11 output currents. The "flash" LEDs do not need to charge nor
|
| D | leds-lm3532.txt | 7 method allows for different LED currents in each current sink thus allowing
|
| /Linux-v5.10/Documentation/sound/soc/ |
| D | overview.rst | 24 power via changing codec oversampling rates, bias currents, etc.
|
| /Linux-v5.10/Documentation/devicetree/bindings/regulator/ |
| D | gpio-regulator.yaml | 56 description: Selection of available voltages/currents provided by this
|
| /Linux-v5.10/Documentation/devicetree/bindings/mfd/ |
| D | rohm,bd70528-pmic.txt | 9 1S battery charger with scalable charge currents.
|
| D | rohm,bd71828-pmic.yaml | 51 BD71827 and BD71828 have SAR ADC for measuring charging currents.
|
| /Linux-v5.10/Documentation/leds/ |
| D | leds-lm3556.rst | 22 from 93.75 mA to 1500 mA.The Flash currents are adjusted via the CURRENT
|
| /Linux-v5.10/Documentation/driver-api/ |
| D | regulator.rst | 99 interface for this. Both take ranges of voltages and currents, supporting
|
| /Linux-v5.10/drivers/hwmon/pmbus/ |
| D | ucd9200.c | 149 * READ_IOUT will return the sum of currents of all phases of a rail, in ucd9200_probe()
|
| D | max16601.c | 19 * currents for VCORE. Telemetry is reported in vendor specific registers.
|
| /Linux-v5.10/drivers/hwmon/ |
| D | ltc4151.c | 140 /* Currents (via sense resistor) */
|
| D | ltc4261.c | 172 /* Currents (via sense resistor) */
|
| /Linux-v5.10/drivers/video/backlight/ |
| D | cr_bllcd.c | 127 /* Power down LVDS controller first to avoid high currents */ in cr_panel_off()
|
| /Linux-v5.10/Documentation/power/ |
| D | power_supply_class.rst | 51 All voltages, currents, charges, energies, time and temperatures in µV,
|
| /Linux-v5.10/Documentation/core-api/ |
| D | kernel-api.rst | 346 called a *retention mode*. This mode still incurs leakage currents,
|
