Home
last modified time | relevance | path

Searched +full:charge +full:- +full:current (Results 1 – 25 of 814) sorted by relevance

12345678910>>...33

/Linux-v6.6/Documentation/devicetree/bindings/power/supply/
Dgpio-charger.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/power/supply/gpio-charger.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Sebastian Reichel <sre@kernel.org>
19 const: gpio-charger
21 charger-type:
23 - unknown
24 - battery
25 - ups
[all …]
Drichtek,rt5033-charger.yaml1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/power/supply/richtek,rt5033-charger.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Jakob Hauser <jahau@rocketmail.com>
14 under sub-node named "charger" using the following format.
18 const: richtek,rt5033-charger
20 monitored-battery:
26 precharge-current-microamp:
27 Current of pre-charge mode. The pre-charge current levels are 350 mA
[all …]
Dqcom,pm8941-charger.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/power/supply/qcom,pm8941-charger.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Qualcomm Switch-Mode Battery Charger and Boost
10 - Sebastian Reichel <sre@kernel.org>
15 - qcom,pm8226-charger
16 - qcom,pm8941-charger
23 - description: charge done
24 - description: charge fast mode
[all …]
Drichtek,rt9455.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Sebastian Reichel <sre@kernel.org>
13 - $ref: power-supply.yaml#
25 richtek,output-charge-current:
27 description: output current from the charger to the battery, in uA.
29 richtek,end-of-charge-percentage:
32 percent of the output charge current. When the current in constant-voltage phase drops
33 below output_charge_current x end-of-charge-percentage, charge is terminated.
[all …]
Drohm,bd99954.yaml1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Matti Vaittinen <mazziesaccount@gmail.com>
11 - Markus Laine <markus.laine@fi.rohmeurope.com>
12 - Mikko Mutanen <mikko.mutanen@fi.rohmeurope.com>
15 The ROHM BD99954 is a Battery Management LSI for 1-4 cell Lithium-Ion
16 secondary battery intended to be used in space-constraint equipment such
18 provides a Dual-source Battery Charger, two port BC1.2 detection and a
21 $ref: power-supply.yaml#
[all …]
Dbattery.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Sebastian Reichel <sre@kernel.org>
14 In smart batteries, these are typically stored in non-volatile memory
16 no appropriate non-volatile memory, or it is unprogrammed/incorrect.
27 Batteries must be referenced by chargers and/or fuel-gauges using a phandle.
28 The phandle's property should be named "monitored-battery".
32 const: simple-battery
34 device-chemistry:
[all …]
Dsummit,smb347-charger.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/power/supply/summit,smb347-charger.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - David Heidelberg <david@ixit.cz>
11 - Dmitry Osipenko <digetx@gmail.com>
16 - summit,smb345
17 - summit,smb347
18 - summit,smb358
26 monitored-battery:
[all …]
Dbq25890.yaml1 # SPDX-License-Identifier: GPL-2.0
4 ---
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
8 title: Bq25890, bq25892, bq25895 and bq25896 Li-Ion Charger
11 - Sebastian Reichel <sre@kernel.org>
14 - $ref: power-supply.yaml#
19 - enum:
20 - ti,bq25890
21 - items:
22 - enum:
[all …]
Dbq24257.yaml1 # SPDX-License-Identifier: GPL-2.0
4 ---
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
8 title: Bq24250, bq24251 and bq24257 Li-Ion Charger
11 - Sebastian Reichel <sre@kernel.org>
14 - $ref: power-supply.yaml#
19 - ti,bq24250
20 - ti,bq24251
21 - ti,bq24257
29 ti,battery-regulation-voltage:
[all …]
Dbq2415x.yaml1 # SPDX-License-Identifier: GPL-2.0
4 ---
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
8 title: TI bq2415x Li-Ion Charger
11 - Sebastian Reichel <sre@kernel.org>
14 - $ref: power-supply.yaml#
19 - ti,bq24150
20 - ti,bq24150a
21 - ti,bq24151
22 - ti,bq24151a
[all …]
Dbq2515x.yaml1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
4 ---
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
8 title: TI bq2515x 500-mA Linear charger family
11 - Andrew Davis <afd@ti.com>
14 The BQ2515x family is a highly integrated battery charge management IC that
17 push-button controller.
26 - ti,bq25150
27 - ti,bq25155
33 ac-detect-gpios:
[all …]
Dsc2731-charger.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/power/supply/sc2731-charger.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Sebastian Reichel <sre@kernel.org>
13 - $ref: power-supply.yaml#
17 const: sprd,sc2731-charger
26 monitored-battery:
29 - charge-term-current-microamp: current for charge termination phase.
30 - constant-charge-voltage-max-microvolt: maximum constant input voltage.
[all …]
Dbq24190.yaml1 # SPDX-License-Identifier: GPL-2.0
4 ---
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
8 title: TI BQ2419x Li-Ion Battery Charger
11 - Sebastian Reichel <sre@kernel.org>
14 - $ref: power-supply.yaml#
19 - ti,bq24190
20 - ti,bq24192
21 - ti,bq24192i
22 - ti,bq24196
[all …]
Dcpcap-charger.yaml1 # SPDX-License-Identifier: GPL-2.0
4 ---
5 $id: http://devicetree.org/schemas/power/supply/cpcap-charger.yaml#
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
11 - Tony Lindgren <tony@atomide.com>
12 - Sebastian Reichel <sre@kernel.org>
17 sub-function.
20 - $ref: power-supply.yaml#
24 const: motorola,mapphone-cpcap-charger
28 - description: charger detection interrupt
[all …]
Dbq256xx.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
4 ---
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
11 - Andrew Davis <afd@ti.com>
14 The bq256xx devices are a family of highly-integrated battery charge
15 management and system power management ICs for single cell Li-ion and Li-
19 - https://www.ti.com/lit/ds/symlink/bq25600.pdf
20 - https://www.ti.com/lit/ds/symlink/bq25601.pdf
21 - https://www.ti.com/lit/ds/symlink/bq25600d.pdf
22 - https://www.ti.com/lit/ds/symlink/bq25601d.pdf
[all …]
/Linux-v6.6/arch/arm/boot/dts/microchip/
Dat91-natte.dtsi1 // SPDX-License-Identifier: GPL-2.0+
3 * at91-natte.dts - Device Tree include file for the Natte board
11 mux: mux-controller {
12 compatible = "gpio-mux";
13 #mux-control-cells = <0>;
15 mux-gpios = <&ioexp 0 GPIO_ACTIVE_HIGH>,
20 batntc-mux {
21 compatible = "io-channel-mux";
22 io-channels = <&adc 5>;
23 io-channel-names = "parent";
[all …]
/Linux-v6.6/Documentation/power/
Dpower_supply_class.rst8 properties to user-space.
60 +--------------------------------------------------------------------------+
61 | **Charge/Energy/Capacity - how to not confuse** |
62 +--------------------------------------------------------------------------+
63 | **Because both "charge" (µAh) and "energy" (µWh) represents "capacity" |
66 | - `CHARGE_*` |
68 | - `ENERGY_*` |
70 | - `CAPACITY` |
72 +--------------------------------------------------------------------------+
88 batteries can typically charge at different rates.
[all …]
/Linux-v6.6/include/linux/mfd/wm8350/
Dsupply.h1 /* SPDX-License-Identifier: GPL-2.0-or-later */
3 * supply.h -- Power Supply Driver for Wolfson WM8350 PMIC
22 * R168 (0xA8) - Battery Charger Control 1
39 * R169 (0xA9) - Battery Charger Control 2
54 * R170 (0xAA) - Battery Charger Control 3
84 #define WM8350_CHG_EOC_mA(x) (((x - 10) & 0x7) << 10)
108 /* charger state machine policy - set in machine driver */
109 int eoc_mA; /* end of charge current (mA) */
110 int charge_mV; /* charge voltage */
111 int fast_limit_mA; /* fast charge current limit */
[all …]
/Linux-v6.6/drivers/power/supply/
Drk817_charger.c1 // SPDX-License-Identifier: GPL-2.0+
12 #include <linux/devm-helpers.h>
33 * Max charging current read to/written from hardware register.
35 * current, this is per the datasheet.
68 * soc - state of charge - like the BSP this is stored as a percentage,
69 * to the thousandth. BSP has a display state of charge (dsoc) and a
70 * remaining state of charge (rsoc). This value will be used for both
72 * charge and just report it as it is. Note for example an soc of 100
115 #define CURRENT_TO_ADC(current, samp_res) \ argument
116 (current * samp_res / 172)
[all …]
Dbd99954-charger.c1 // SPDX-License-Identifier: GPL-2.0-only
16 * Curve (1) represents charging current.
20 * a) Trickle-charge with constant current (8).
21 * b) pre-charge with constant current (6)
22 * c) fast-charge, first with constant current (5) phase. After
24 * voltage phase until charging current has dropped to termination
30 *(4)` `.` ` ` ` ` ` ` ` ` ` ` ` ` ` ----------------------------.
32 * . o----+/:/ ` ` ` ` ` ` ` ` ` ` ` ` `.` ` (5)
34 * . + /- -- .
35 * . +`/- + .
[all …]
Dsc2731_charger.c1 // SPDX-License-Identifier: GPL-2.0
46 /* Default current definition (unit is mA) */
69 regmap_update_bits(info->regmap, info->base + SC2731_CHG_CFG0, in sc2731_charger_stop_charge()
72 regmap_update_bits(info->regmap, info->base + SC2731_CHG_CFG0, in sc2731_charger_stop_charge()
80 /* Enable charger constant current mode */ in sc2731_charger_start_charge()
81 ret = regmap_update_bits(info->regmap, info->base + SC2731_CHG_CFG0, in sc2731_charger_start_charge()
87 return regmap_update_bits(info->regmap, info->base + SC2731_CHG_CFG0, in sc2731_charger_start_charge()
105 return regmap_update_bits(info->regmap, info->base + SC2731_CHG_CFG5, in sc2731_charger_set_current_limit()
121 val = (cur - SC2731_CURRENT_PRECHG) / SC2731_CURRENT_STEP; in sc2731_charger_set_current()
123 /* Set pre-charge current as 450 mA */ in sc2731_charger_set_current()
[all …]
/Linux-v6.6/Documentation/ABI/testing/
Dsysfs-class-power5 Contact: linux-pm@vger.kernel.org
14 Contact: linux-pm@vger.kernel.org
23 Contact: linux-pm@vger.kernel.org
32 Contact: linux-pm@vger.kernel.org
43 Contact: linux-pm@vger.kernel.org
47 Reports an average IBAT current reading for the battery, over
54 Reports an average IBUS current reading over a fixed period.
62 batteries and for USB IBUS current.
66 Contact: linux-pm@vger.kernel.org
70 Reports the maximum IBAT current allowed into the battery.
[all …]
/Linux-v6.6/Documentation/devicetree/bindings/rtc/
Drtc-palmas.txt4 - compatible:
5 - "ti,palmas-rtc" for palma series of the RTC controller
6 - interrupts: Interrupt number of RTC submodule on device.
10 - ti,backup-battery-chargeable: The Palmas series device like TPS65913 or
13 can be chargeable or non-chargeable. This flag will tells whether
16 - ti,backup-battery-charge-high-current: Enable high current charging in
18 The high current will be > 100uA. Absence of this property will
19 charge battery to lower current i.e. < 100uA.
25 compatible = "ti,palmas-rtc";
26 interrupt-parent = <&palmas>;
[all …]
/Linux-v6.6/include/linux/
Dpower_supply.h1 /* SPDX-License-Identifier: GPL-2.0-only */
226 /* Run-time specific power supply configuration */
359 * struct power_supply_maintenance_charge_table - setting for maintenace charging
360 * @charge_current_max_ua: maintenance charging current that is used to keep
361 * the charge of the battery full as current is consumed after full charging.
363 * reach this voltage the maintenance charging current is turned off. It is
371 * maintenance charge current and voltage pair in respective array and wait
378 * Ordinary CC/CV charging will stop charging when the charge current goes
384 * the power used in standby mode. This will over time give a charge graph
392 * +-------------------------------------------------------------------> t
[all …]
/Linux-v6.6/include/linux/mfd/wm831x/
Dpdata.h1 /* SPDX-License-Identifier: GPL-2.0-or-later */
3 * include/linux/mfd/wm831x/pdata.h -- Platform data for WM831x
18 int max_uA; /** Maximum current to allow */
25 int ilim; /** Current limit in microamps */
32 int trickle_ilim; /** Trickle charge current limit, in mA */
34 int eoc_iterm; /** End of trickle charge current, in mA */
35 int fast_ilim; /** Fast charge current limit, in mA */
36 int timeout; /** Charge cycle timeout, in minutes */
40 * Configuration for the WM831x DC-DC BuckWise convertors. This
59 WM831X_STATUS_PRESERVE = 0, /* Keep the current hardware setting */
[all …]

12345678910>>...33