Searched full:can1 (Results 1 – 25 of 248) sorted by relevance
12345678910
| /Linux-v6.1/drivers/net/can/sja1000/ |
| D | tscan1.c | 3 * tscan1.c: driver for Technologic Systems TS-CAN1 PC104 boards
9 * - Getting started with TS-CAN1, Technologic Systems, Feb 2022
10 * https://docs.embeddedts.com/TS-CAN1
21 MODULE_DESCRIPTION("Driver for Technologic Systems TS-CAN1 PC104 boards");
77 /* Probe for a TS-CAN1 board with JP2:JP1 jumper setting ID */
144 netdev_info(netdev, "TS-CAN1 at 0x%lx 0x%lx irq %d\n", in tscan1_probe()
|
| D | Kconfig | 106 tristate "TS-CAN1 PC104 boards"
110 https://www.embeddedts.com/products/TS-CAN1
|
| /Linux-v6.1/arch/arm64/boot/dts/renesas/ |
| D | cat875.dtsi | 40 &can1 {
63 can1_pins: can1 {
65 function = "can1";
|
| D | hihope-rzg2-ex.dtsi | 42 &can1 {
79 can1_pins: can1 {
81 function = "can1";
|
| D | rzg2lc-smarc-pinfunction.dtsi | 17 can1_pins: can1 {
25 can1-stb-hog {
32 can1_pins: can1 {
|
| D | rzg2lc-smarc.dtsi | 15 * SW1-3 : SW_SCIF_CAN (1: CAN1; 0: SCIF1)
16 * SW1-4 : SW_RSPI_CAN (1: CAN1; 0: RSPI1)
|
| D | rzg2ul-smarc-pinfunction.dtsi | 29 can1_pins: can1 {
35 can1-stb-hog {
|
| D | rzg2l-smarc-pinfunction.dtsi | 28 can1_pins: can1 {
34 can1-stb-hog {
|
| /Linux-v6.1/arch/arm/boot/dts/ |
| D | iwg20d-q7-dbcm-ca.dtsi | 32 &can1 {
98 can1_pins: can1 {
100 function = "can1";
|
| D | r8a7745-iwg22d-sodimm-dbhd-ca.dts | 54 &can1 {
116 can1_pins: can1 {
118 function = "can1";
|
| D | r9a06g032-rzn1d400-db.dts | 33 /* Assuming CN10/CN11 are wired for CAN1 */
37 &can1 {
41 /* Please only enable can0 or can1, depending on CN10/CN11 */
|
| D | imx6qdl-skov-cpu.dtsi | 14 can0 = &can1;
15 can1 = &can2;
132 reg_can1_stby: regulator-can1-stby {
136 regulator-name = "can1-3v3";
193 &can1 {
|
| D | at91sam9x5_can.dtsi | 26 can1: can@f8004000 { label
46 can1 {
|
| D | sama5d3_can.dtsi | 24 can1 {
45 can1: can@f8010000 { label
|
| D | r8a7792-wheat.dts | 142 can1_pins: can1 {
144 function = "can1";
187 &can1 {
|
| D | lpc4357-myd-lpc4357.dts | 103 can1_pins: can1-pins {
106 function = "can1";
112 function = "can1";
463 &can1 {
|
| D | spear320-evb.dts | 64 can1 {
66 st,function = "can1";
|
| D | r8a7742-iwg21d-q7.dts | 213 &can1 {
329 can1_pins: can1 {
331 function = "can1";
|
| /Linux-v6.1/Documentation/devicetree/bindings/net/can/ |
| D | renesas,rcar-canfd.yaml | 116 - description: CAN1 error interrupt
117 - description: CAN1 transmit interrupt
118 - description: CAN1 transmit/receive FIFO receive completion interrupt
|
| /Linux-v6.1/Documentation/devicetree/bindings/reset/ |
| D | zynq-reset.txt | 46 257: can1 reset
48 259: can1 ref reset
|
| /Linux-v6.1/arch/arm64/boot/dts/freescale/ |
| D | imx8mp-evk.dts | 43 reg_can1_stby: regulator-can1-stby {
45 regulator-name = "can1-stby";
339 "CAN1/I2C5_SEL",
361 status = "disabled"; /* can1 pins conflict with i2c5 */
363 /* GPIO 2 of PCA6416 is used to switch between CAN1 and I2C5 functions:
364 * LOW: CAN1 (default, pull-down)
|
| /Linux-v6.1/arch/powerpc/boot/dts/fsl/ |
| D | p1010si-pre.dtsi | 54 can1 = &can1;
|
| /Linux-v6.1/Documentation/devicetree/bindings/clock/ |
| D | zynq-7000.txt | 61 20: can1
99 "fclk0", "fclk1", "fclk2", "fclk3", "can0", "can1",
|
| /Linux-v6.1/arch/arm64/boot/dts/xilinx/ |
| D | zynqmp-zc1751-xm016-dc2.dts | 49 &can1 {
180 pinctrl_can1_default: can1-default {
182 function = "can1";
|
| /Linux-v6.1/Documentation/devicetree/bindings/pinctrl/ |
| D | pinctrl_spear.txt | 140 "can0", "can1", "pwm0_1", "pwm2", "pwm3", "ssp1", "ssp2", "mii2",
149 "i2c_4_5", "i2c_6_7", "can0", "can1", "pci", "sata", "ssp1", "gpt64"
|
12345678910
