| /Linux-v5.15/drivers/net/wireless/broadcom/b43/ |
| D | lo.h | 20 /* This struct holds calibrated LO settings for a set of
24 * control values is calibrated for. */
29 /* The time when these settings were calibrated (in jiffies) */
49 /* List of calibrated control values (struct b43_lo_calib). */
|
| /Linux-v5.15/Documentation/devicetree/bindings/display/tegra/ |
| D | nvidia,tegra114-mipi.txt | 11 that need to be calibrated for a given device.
15 that need to be calibrated.
|
| /Linux-v5.15/drivers/pps/generators/ |
| D | pps_gen_parport.c | 44 long port_write_time; /* calibrated port write time (ns) */
53 /* calibrated time between a hrtimer event and the reaction */
112 /* update calibrated port write time */ in hrtimer_event()
118 /* update calibrated hrtimer error */ in hrtimer_event()
|
| /Linux-v5.15/include/linux/mtd/ |
| D | hyperbus.h | 71 * @calibrated: flag to indicate ctlr calibration sequence is complete
76 bool calibrated; member
|
| /Linux-v5.15/include/linux/ |
| D | led-lm3530.h | 92 * @als_vmin: als input voltage calibrated for max brightness in mV
93 * @als_vmax: als input voltage calibrated for min brightness in mV
|
| /Linux-v5.15/drivers/mtd/hyperbus/ |
| D | hyperbus-core.c | 99 if (ops->calibrate && !ctlr->calibrated) { in hyperbus_register_device()
105 ctlr->calibrated = true; in hyperbus_register_device()
|
| /Linux-v5.15/drivers/iio/chemical/ |
| D | atlas-sensor.c | 252 dev_warn(dev, "device has not been calibrated\n"); in atlas_check_ph_calibration()
287 dev_warn(dev, "device has not been calibrated\n"); in atlas_check_ec_calibration()
318 dev_warn(dev, "device has not been calibrated\n"); in atlas_check_orp_calibration()
334 dev_warn(dev, "device has not been calibrated\n"); in atlas_check_do_calibration()
|
| /Linux-v5.15/drivers/macintosh/ams/ |
| D | ams.h | 57 /* calibrated null values */
|
| /Linux-v5.15/Documentation/devicetree/bindings/thermal/ |
| D | socionext,uniphier-thermal.yaml | 34 A pair of calibrated values referred from PVT, in case that the values
|
| D | qcom-spmi-adc-tm5.yaml | 76 channel will be calibrated with 0V and 1.25V reference channels,
|
| /Linux-v5.15/Documentation/devicetree/bindings/iio/temperature/ |
| D | melexis,mlx90632.yaml | 24 temperature. MLX90632 can be calibrated to reduce the housing effect via
|
| /Linux-v5.15/Documentation/devicetree/bindings/iio/adc/ |
| D | qcom,spmi-vadc.yaml | 116 calibrated with 0.625V and 1.25V reference channels, also
121 property is not found, channel will be calibrated with 0V and 1.25V
|
| /Linux-v5.15/arch/x86/kernel/ |
| D | i8253.c | 29 * calibrated against the PIT interrupt.
|
| D | io_delay.c | 54 * are shorter until calibrated): in native_io_delay()
|
| /Linux-v5.15/Documentation/timers/ |
| D | timekeeping.rst | 166 jiffy) value, calibrated on boot.
169 is calibrated: as an effect when the frequency is geared down to half the
|
| /Linux-v5.15/drivers/thermal/ |
| D | uniphier_thermal.c | 103 * Since SoC has a calibrated value that was set in advance, in uniphier_tm_initialize_sensor()
106 * If TMODCOEF shows zero, the boards don't have the calibrated in uniphier_tm_initialize_sensor()
|
| /Linux-v5.15/Documentation/usb/ |
| D | mtouchusb.rst | 53 the device could be calibrated, the driver pulls to raw coordinate data from
|
| /Linux-v5.15/Documentation/misc-devices/ |
| D | bh1770glc.rst | 45 calibrated source of light is needed as a reference. Calibscale factor is set
|
| /Linux-v5.15/include/linux/iio/common/ |
| D | cros_ec_sensors_core.h | 50 * captured data will always provide the calibrated
|
| /Linux-v5.15/drivers/media/platform/marvell-ccic/ |
| D | mmp-driver.c | 86 * The value has been calibrated on in mmpcam_calc_dphy()
137 * The value is calibrated on the boards. in mmpcam_calc_dphy()
|
| /Linux-v5.15/Documentation/devicetree/bindings/phy/ |
| D | apm-xgene-phy.txt | 18 bit lines from the automatic calibrated position.
|
| /Linux-v5.15/drivers/mfd/ |
| D | iqs62x.c | 932 * numbers. It then determines if the device is factory-calibrated by in iqs62x_probe()
937 * For devices given in both calibrated and uncalibrated versions, the in iqs62x_probe()
938 * calibrated version (e.g. IQS620AT) appears first in the iqs62x_devs in iqs62x_probe()
976 * and the device is calibrated (if applicable). in iqs62x_probe()
|
| /Linux-v5.15/drivers/iio/adc/ |
| D | twl6030-gpadc.c | 74 * GPADC is calibrated in two points: close to the beginning and
431 /* not calibrated channels have 0 in all structure members */ in twl6030_channel_calibrated()
550 * The GPADC channels are calibrated using a two point calibration method.
555 * The goal is to find offset and gain of the real curve for each calibrated
|
| /Linux-v5.15/tools/testing/selftests/powerpc/pmu/ebb/ |
| D | instruction_count_test.c | 17 * Run a calibrated instruction loop and count instructions executed using
|
| /Linux-v5.15/drivers/iio/temperature/ |
| D | tmp117.c | 9 * Note: This driver assumes that the sensor has been calibrated beforehand.
|
