| /Linux-v6.1/Documentation/devicetree/bindings/mfd/ |
| D | samsung,s5m8767.yaml | 47 s5m8767,pmic-buck3-dvs-voltage:
52 A set of 8 voltage values in micro-volt (uV) units for buck3 when
74 s5m8767,pmic-buck3-uses-gpio-dvs:
76 description: buck3 can be controlled by gpio dvs.
104 description: Power supply for buck3
147 s5m8767,pmic-buck3-dvs-voltage: [ 's5m8767,pmic-buck-dvs-gpios' ]
150 …s5m8767,pmic-buck3-uses-gpio-dvs: [ 's5m8767,pmic-buck-dvs-gpios', 's5m8767,pmic-buck3-dvs-voltage…
161 s5m8767,pmic-buck3-uses-gpio-dvs: false
166 - s5m8767,pmic-buck3-uses-gpio-dvs
178 s5m8767,pmic-buck3-uses-gpio-dvs: false
[all …]
|
| D | ti,lp87524-q1.yaml | 45 - buck3
61 - buck3-in-supply
82 buck3-in-supply = <&vdd_5v0>;
106 buck3_reg: buck3 {
107 regulator-name = "buck3";
|
| D | richtek,rt5120.yaml | 56 description: phandle for buck3 input power source
147 buck3 {
148 regulator-name = "rt5120-buck3";
|
| D | da9052-i2c.txt | 21 buck3 : regulator BUCK MEM
56 buck3 {
|
| D | rohm,bd71815-pmic.yaml | 137 buck3: buck3 {
138 regulator-name = "buck3";
|
| D | rohm,bd71828-pmic.yaml | 125 buck3: BUCK3 {
126 regulator-name = "buck3";
|
| D | rohm,bd71847-pmic.yaml | 171 buck3: BUCK3 {
172 regulator-name = "buck3";
|
| D | rohm,bd71837-pmic.yaml | 167 buck3: BUCK3 {
168 regulator-name = "buck3";
|
| D | st,stpmic1.yaml | 90 - buck3 for Buck BUCK3
309 buck3 {
|
| D | da9062.txt | 58 buck3 : BUCK_3
69 buck3 : BUCK_3
|
| /Linux-v6.1/Documentation/devicetree/bindings/regulator/ |
| D | pv88080.txt | 17 BUCK1, BUCK2, BUCK3 and HVBUCK.
47 BUCK3 {
48 regulator-name = "buck3";
|
| D | pv88090.txt | 11 BUCK1, BUCK2, BUCK3, LDO1, and LDO2.
42 BUCK3 {
43 regulator-name = "buck3";
|
| D | richtek,rt5190a-regulator.yaml | 35 description: phandle to buck3 input voltage.
120 buck3 {
121 regulator-name = "rt5190a-buck3";
|
| D | richtek,rtq2134-regulator.yaml | 93 buck3 {
94 regulator-name = "rtq2134-buck3";
|
| D | ti,tps65219.yaml | 105 buck3-supply = <&vcc_3v3_sys>;
134 buck3_reg: buck3 {
|
| D | nxp,pca9450-regulator.yaml | 21 #BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6,
23 #Note: Buck3 removed on PCA9450B and connect with Buck1 on PCA9450C.
|
| /Linux-v6.1/drivers/regulator/ |
| D | tps65219-regulator.c | 46 { "BUCK3_SCG", "BUCK3", "short circuit to ground", REGULATOR_EVENT_REGULATION_OUT },
47 { "BUCK3_OC", "BUCK3", "overcurrent", REGULATOR_EVENT_OVER_CURRENT },
48 { "BUCK3_NEG_OC", "BUCK3", "negative overcurrent", REGULATOR_EVENT_OVER_CURRENT },
49 { "BUCK3_UV", "BUCK3", "undervoltage", REGULATOR_EVENT_UNDER_VOLTAGE },
60 { "BUCK3_RV", "BUCK3", "residual voltage", REGULATOR_EVENT_OVER_VOLTAGE_WARN },
69 { "BUCK3_RV_SD", "BUCK3", "residual voltage on shutdown",
252 TPS65219_REGULATOR("BUCK3", "buck3", TPS65219_BUCK_3,
|
| D | tps65086-regulator.c | 17 enum tps65086_regulators { BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6, LDOA1, enumerator
126 TPS65086_REGULATOR("BUCK3", "buck3", BUCK3, 0x80, TPS65086_BUCK3VID,
174 case BUCK3: in tps65086_of_parse_cb()
|
| D | lp8788-buck.c | 84 BUCK3, enumerator
393 .name = "buck3",
394 .id = BUCK3,
466 /* no dvs for buck3, 4 */ in lp8788_init_dvs()
|
| D | mcp16502.c | 97 /* Ramp delay (uV/us) for buck2, buck3, buck4. */
137 BUCK3, enumerator
312 case BUCK3: in mcp16502_set_voltage_time_sel()
475 MCP16502_REGULATOR("VDD_CORE", BUCK3, b234_ranges, mcp16502_buck_ops,
|
| D | da9052-regulator.c | 333 DA9052_DCDC(BUCK3, buck3, 25, 950, 2525, 6, 6, DA9052_SUPPLY_VBMEMGO),
350 DA9052_DCDC(BUCK3, buck3, 25, 950, 2525, 6, 6, DA9052_SUPPLY_VBMEMGO),
|
| D | pv88080-regulator.c | 86 /* Current limits array (in uA) for BUCK1, BUCK2, BUCK3.
136 /* BUCK3 */
180 /* BUCK3 */
321 PV88080_BUCK(PV88080, BUCK3, 600000, 6250, 1393750,
|
| /Linux-v6.1/arch/arm64/boot/dts/freescale/ |
| D | imx8mn-ddr4-evk.dts | 85 buck3_reg: BUCK3 {
87 regulator-name = "buck3";
|
| D | imx8mq-pico-pi.dts | 99 buck3: BUCK3 { label
100 regulator-name = "buck3";
|
| D | imx8mq-phanbell.dts | 154 buck3: BUCK3 { label
155 regulator-name = "buck3";
|
