Searched full:allowable (Results 1 – 25 of 114) sorted by relevance
12345
33 * @pllm_min: Minimum allowable value for PLLM[PLLM]34 * @pllm_max: Maximum allowable value for PLLM[PLLM]35 * @pllout_min_rate: Minimum allowable rate for PLLOUT36 * @pllout_max_rate: Maximum allowable rate for PLLOUT
18 This is an integer and represents allowable DMA bursts when fixed burst.19 Allowable range is 0x01-0x3F. When this field is set fixed burst is enabled.20 When fixed length is needed for burst mode, it can be set within allowable
29 allowable by a module in the slot, in milli-Watts. Presently, modules can
106 * @lo: lowest allowable value107 * @hi: highest allowable value205 * @lo: minimum allowable value206 * @hi: maximum allowable value216 * @lo: minimum allowable value217 * @hi: maximum allowable value
22 * Maximum allowable number of contiguous slabs to map,
200 int "Clocksource watchdog maximum allowable skew (in μs)"205 Specify the maximum amount of allowable watchdog skew in
6 * may_use_simd - whether it is allowable at this time to issue SIMD
374 "Description": "Setting generous range for allowable frequencies",389 "Description": "Setting generous range for allowable frequencies",
426 * @min_freq_hz: The minimum allowable frequency in Hz. This is the minimum427 * allowable programmed frequency and does not account for clock431 * @max_freq_hz: The maximum allowable frequency in Hz. This is the maximum432 * allowable programmed frequency and does not account for clock473 * @min_freq_hz: The minimum allowable frequency in Hz. This is the minimum474 * allowable programmed frequency and does not account for clock478 * @max_freq_hz: The maximum allowable frequency in Hz. This is the maximum479 * allowable programmed frequency and does not account for clock489 * This sets the desired frequency for a clock within an allowable
15 Allowable values of 0x00 through 0x0F. These are raw values written to the
18 Allowable values of 0x00 through 0x0F. These are raw values written to the
20 * may_use_simd - whether it is allowable at this time to issue SIMD
158 * -min_freq: The minimum allowable frequency in Hz. This is the minimum159 * allowable programmed frequency and does not account for clock163 * -max_freq: The maximum allowable frequency in Hz. This is the maximum164 * allowable programmed frequency and does not account for clock
49 /* Powerdomain allowable state bitfields */
39 * @max_core_clk_rate: maximum allowable core clock rate
5 * linkmode_resolve_pause - resolve the allowable pause modes
18 /* Max number of segments allowable in LUX table */
292 uint16_t MaxVoltageGfx; // In mV(Q2) Maximum Voltage allowable of VDD_GFX293 uint16_t MaxVoltageSoc; // In mV(Q2) Maximum Voltage allowable of VDD_SOC
661 uint16_t MaxVoltageGfx; // In mV(Q2) Maximum Voltage allowable of VDD_GFX662 uint16_t MaxVoltageSoc; // In mV(Q2) Maximum Voltage allowable of VDD_SOC1021 uint16_t MaxVoltageGfx; // In mV(Q2) Maximum Voltage allowable of VDD_GFX1022 uint16_t MaxVoltageSoc; // In mV(Q2) Maximum Voltage allowable of VDD_SOC
59 * Max allowable width is limited on a per device basis
71 * insane value at boot (values outside of the allowable frequency in shoc_clk_init()
63 * @timeout: maximum allowable time in jiffies between start I/O and interrupt
144 countries define different levels of allowable transmitter
64 #define NR_MAX_WINDOW_SIZE 127 /* Maximum Window Allowable - 127 */
