Searched full:actively (Results 1 – 25 of 176) sorted by relevance
12345678
| /Linux-v5.15/Documentation/devicetree/bindings/pinctrl/ |
| D | pincfg-node.yaml | 56 description: drive actively high and low
114 description: enable output on a pin without actively driving it
|
| D | pinctrl-sx150x.txt | 47 - drive-push-pull: drive actively high and low
|
| /Linux-v5.15/include/media/ |
| D | tuner.h | 21 #define TUNER_PHILIPS_SECAM 3 /* you must actively select B/G, L, L` */
45 #define TUNER_TEMIC_4046FM5 22 /* you must actively select B/G, D/K, I, L, L` ! (3X 7804, 7806, 8…
48 #define TUNER_PHILIPS_FQ1216ME 24 /* you must actively select B/G/D/K, I, L, L` */
|
| /Linux-v5.15/drivers/acpi/nfit/ |
| D | Kconfig | 25 by default. If you are a kernel developer actively working
|
| /Linux-v5.15/include/uapi/misc/uacce/ |
| D | uacce.h | 15 * User actively stop queue and free queue resource immediately
|
| /Linux-v5.15/include/linux/platform_data/ |
| D | i2c-gpio.h | 16 * isn't actively driven high when setting the output value high.
|
| /Linux-v5.15/include/sound/ |
| D | wm2200.h | 39 unsigned int discharge:1; /** Actively discharge */
|
| /Linux-v5.15/Documentation/devicetree/bindings/regulator/ |
| D | tps65132-regulator.txt | 19 the enable signal goes low. This GPIO is used to actively discharge
|
| /Linux-v5.15/include/linux/ |
| D | livepatch.h | 150 * @replace: replace all actively used patches
151 * @list: list node for global list of actively used patches
|
| D | hash.h | 12 * were actively bad for hashing), but the name remains.
|
| /Linux-v5.15/Documentation/admin-guide/mm/ |
| D | soft-dirty.rst | 43 This feature is actively used by the checkpoint-restore project. You
|
| /Linux-v5.15/Documentation/networking/ |
| D | x25.rst | 32 be actively considered.
|
| /Linux-v5.15/include/soc/qcom/ |
| D | tcs.h | 16 * resource actively.
|
| /Linux-v5.15/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/ |
| D | pincfg.txt | 18 0 = The pin is actively driven as an output
|
| /Linux-v5.15/Documentation/devicetree/bindings/thermal/ |
| D | thermal-sensor.yaml | 21 - cooling-device: device used to dissipate heat either passively or actively
|
| D | thermal-cooling-devices.yaml | 21 - cooling-device: device used to dissipate heat either passively or actively
|
| /Linux-v5.15/kernel/time/ |
| D | tick-sched.h | 31 * @idle_active: Indicator that the CPU is actively in the tick idle mode;
|
| /Linux-v5.15/Documentation/hwmon/ |
| D | lm73.rst | 79 conversion time actively in use.
|
| /Linux-v5.15/tools/include/linux/ |
| D | hash.h | 12 * were actively bad for hashing), but the name remains.
|
| /Linux-v5.15/Documentation/driver-api/gpio/ |
| D | driver.rst | 136 Open drain (CMOS) or open collector (TTL) means the line is not actively driven
162 the rail actively pulls it down.
192 is then halved and give high impedance instead of actively driving the line
227 of actively driving the line low, it is set to input.
|
| /Linux-v5.15/drivers/usb/gadget/ |
| D | Kconfig | 56 Avoid enabling these messages, even if you're actively
70 Avoid enabling these messages, even if you're actively
|
| /Linux-v5.15/include/net/netns/ |
| D | sctp.h | 34 * We actively maintain this complete list of addresses on
|
| /Linux-v5.15/Documentation/x86/ |
| D | amd-memory-encryption.rst | 85 Supported, Enabled and the Linux kernel is actively applying
|
| /Linux-v5.15/tools/testing/selftests/arm64/signal/ |
| D | test_signals_utils.h | 44 * used actively with a sigreturn: in such a case the execution would have
|
| /Linux-v5.15/arch/sparc/kernel/ |
| D | kprobes.c | 33 * - Mark that we are actively in a kprobe
42 * - Mark that we are no longer actively in a kprobe.
|
12345678
