Searched full:port6 (Results 1 – 21 of 21) sorted by relevance
| /Linux-v6.1/Documentation/devicetree/bindings/net/ |
| D | mscc,vsc7514-switch.yaml | 40 - description: Port6 target
64 - const: port6
168 "port2", "port3", "port4", "port5", "port6",
|
| /Linux-v6.1/arch/arm/boot/dts/ |
| D | r7s9210-rza2mevb.dts | 75 gpios = <&pinctrl RZA2_PIN(PORT6, 0) GPIO_ACTIVE_HIGH>;
140 <RZA2_PINMUX(PORT6, 1, 7)>, /* RMMI0_TXDEN */
141 <RZA2_PINMUX(PORT6, 2, 7)>, /* RMII0_TXD0 */
142 <RZA2_PINMUX(PORT6, 3, 7)>, /* RMII0_TXD1 */
|
| D | r7s72100-gr-peach.dts | 61 gpios = <&port6 12 GPIO_ACTIVE_HIGH>;
|
| D | lan966x-kontron-kswitch-d10-mmt.dtsi | 155 &port6 {
|
| D | lan966x-pcb8290.dts | 148 &port6 {
|
| D | imx51-zii-scu2-mezz.dts | 75 label = "port6";
|
| D | lan966x.dtsi | 148 port6: port@6 { label
|
| D | r7s72100.dtsi | 543 port6: gpio-6 { label
|
| /Linux-v6.1/include/dt-bindings/pinctrl/ |
| D | r7s9210-pinctrl.h | 18 #define PORT6 6 macro
|
| /Linux-v6.1/arch/mips/boot/dts/mscc/ |
| D | ocelot.dtsi | 142 "port2", "port3", "port4", "port5", "port6",
176 port6: port@6 { label
|
| D | ocelot_pcb120.dts | 109 &port6 {
|
| /Linux-v6.1/drivers/net/wireguard/ |
| D | socket.c | 367 struct udp_port_cfg port6 = { in wg_socket_init() local
397 port6.local_udp_port = inet_sk(new4->sk)->inet_sport; in wg_socket_init()
398 ret = udp_sock_create(net, &port6, &new6); in wg_socket_init()
|
| /Linux-v6.1/Documentation/devicetree/bindings/pinctrl/ |
| D | renesas,rza2-pinctrl.yaml | 35 E.g. "RZA2_PIN(PORT6, 0)" for P6_0.
|
| /Linux-v6.1/Documentation/driver-api/cxl/ |
| D | memory-devices.rst | 119 "port":"port6",
121 "endpoints:port6":[
|
| /Linux-v6.1/drivers/net/dsa/qca/ |
| D | qca8k.h | 175 * [7:6] for port1 ... [17:16] for port6. Use virtual port
368 u8 rgmii_rx_delay[QCA8K_NUM_CPU_PORTS]; /* 0: CPU port0, 1: CPU port6 */
369 u8 rgmii_tx_delay[QCA8K_NUM_CPU_PORTS]; /* 0: CPU port0, 1: CPU port6 */
|
| D | qca8k-8xxx.c | 465 .max_register = 0x16ac, /* end MIB - Port6 range */
1672 dev_err(priv->dev, "No cpu port configured in both cpu port0 and port6"); in qca8k_setup()
|
| D | qca8k-common.c | 96 regmap_reg_range(0x1600, 0x16ac), /* MIB - Port6 */
|
| /Linux-v6.1/arch/arm64/boot/dts/microchip/ |
| D | sparx5_pcb135_board.dtsi | 416 port6: port@6 { label
|
| /Linux-v6.1/drivers/net/dsa/ocelot/ |
| D | seville_vsc9953.c | 476 DEFINE_RES_MEM_NAMED(0x0160000, 0x0010000, "port6"),
|
| /Linux-v6.1/drivers/pinctrl/renesas/ |
| D | pfc-r8a73a4.c | 455 /* Port6 */
|
| D | pfc-r8a7740.c | 616 /* Port6 */
|
