Searched full:mx6ul (Results 1 – 25 of 25) sorted by relevance
| /Linux-v6.1/Documentation/devicetree/bindings/arm/ |
| D | fsl.yaml | 550 - description: i.MX6UL based Boards
554 - engicam,imx6ul-isiot # Engicam Is.IoT MX6UL eMMC/NAND Starter kit
557 - kontron,sl-imx6ul # Kontron SL i.MX6UL SoM
559 - technexion,imx6ul-pico-dwarf # TechNexion i.MX6UL Pico-Dwarf
560 - technexion,imx6ul-pico-hobbit # TechNexion i.MX6UL Pico-Hobbit
561 - technexion,imx6ul-pico-pi # TechNexion i.MX6UL Pico-Pi
564 - description: i.MX6UL Armadeus Systems OPOS6UL SoM Board
566 - const: armadeus,imx6ul-opos6uldev # OPOS6UL (i.MX6UL) SoM on OPOS6ULDev board
567 - const: armadeus,imx6ul-opos6ul # OPOS6UL (i.MX6UL) SoM
570 - description: i.MX6UL Digi International ConnectCore 6UL Boards
[all …]
|
| /Linux-v6.1/drivers/staging/media/imx/ |
| D | Kconfig | 28 tristate "i.MX6UL/L / i.MX7 / i.MX8M Camera Sensor Interface driver"
32 i.MX6UL/L, i.MX7 or i.MX8M.
|
| D | imx7-media-csi.c | 3 * V4L2 Capture CSI Subdev for Freescale i.MX6UL/L / i.MX7 SOC
|
| /Linux-v6.1/arch/arm/boot/dts/ |
| D | imx6ull.dtsi | 9 /* Delete UART8 in AIPS-1 (i.MX6UL specific) */
11 /* Delete CAAM node in AIPS-2 (i.MX6UL specific) */
|
| D | imx6ul-isiot-emmc.dts | 12 model = "Engicam Is.IoT MX6UL eMMC Starter kit";
|
| D | imx6ul-isiot-nand.dts | 12 model = "Engicam Is.IoT MX6UL NAND Starter kit";
|
| D | imx6ul-kontron-sl.dtsi | 12 model = "Kontron SL i.MX6UL (N631X SOM)";
|
| D | imx6ul-kontron-bl.dts | 14 model = "Kontron BL i.MX6UL (N631X S)";
|
| D | imx6ul-opos6uldev.dts | 10 model = "Armadeus Systems OPOS6UL SoM (i.MX6UL) on OPOS6ULDev board";
|
| D | imx6ul-kontron-bl-43.dts | 11 model = "Kontron BL i.MX6UL 43 (N631X S 43)";
|
| D | imx6ul-litesom.dtsi | 47 model = "Grinn i.MX6UL liteSOM";
|
| D | imx6ul-liteboard.dts | 49 model = "Grinn i.MX6UL liteBoard";
|
| D | imx6ull-pinfunc.h | 14 /* signals common for i.MX6UL and i.MX6ULL */
|
| /Linux-v6.1/drivers/cpufreq/ |
| D | imx6q-cpufreq.c | 32 /* MX6UL requires two more clks */
111 * For i.MX6UL, it has a secondary clk mux, the cpu frequency change in imx6q_set_target()
113 * The cpu frequeny change flow for i.MX6(except i.MX6UL) is as below: in imx6q_set_target()
312 * 2b'10: 696000000Hz on i.MX6UL, 792000000Hz on i.MX6ULL; in imx6ul_opp_check_speed_grading()
|
| /Linux-v6.1/Documentation/devicetree/bindings/input/touchscreen/ |
| D | imx6ul_tsc.txt | 1 * Freescale i.MX6UL Touch Controller
|
| /Linux-v6.1/arch/arm/mach-imx/ |
| D | mach-imx6ul.c | 38 imx_print_silicon_rev(cpu_is_imx6ull() ? "i.MX6ULL" : "i.MX6UL", in imx6ul_init_machine()
|
| /Linux-v6.1/Documentation/devicetree/bindings/nvmem/ |
| D | imx-ocotp.yaml | 14 i.MX6Q/D, i.MX6DL/S, i.MX6SL, i.MX6SX, i.MX6UL, i.MX6ULL/ULZ, i.MX6SLL,
|
| /Linux-v6.1/drivers/soc/imx/ |
| D | soc-imx.c | 103 soc_id = "i.MX6UL"; in imx_soc_device_init()
|
| /Linux-v6.1/drivers/input/touchscreen/ |
| D | imx6ul_tsc.c | 3 // Freescale i.MX6UL touchscreen controller driver
568 MODULE_DESCRIPTION("Freescale i.MX6UL Touchscreen controller driver");
|
| D | Kconfig | 652 tristate "Freescale i.MX6UL touchscreen controller"
655 Say Y here if you have a Freescale i.MX6UL, and want to
|
| /Linux-v6.1/arch/arm/ |
| D | Kconfig.debug | 514 bool "i.MX6UL Debug UART"
518 on i.MX6UL.
|
| /Linux-v6.1/drivers/crypto/caam/ |
| D | ctrl.c | 542 { .soc_id = "i.MX6UL", .data = &caam_imx6ul_data },
|
| /Linux-v6.1/drivers/spi/ |
| D | spi-imx.c | 655 * before i.mx6ul. in mx51_ecspi_prepare_transfer()
|
| /Linux-v6.1/drivers/dma/ |
| D | imx-sdma.c | 510 * and it has been fixed in soc from i.mx6ul.
|
| /Linux-v6.1/drivers/net/ethernet/freescale/ |
| D | fec_main.c | 2435 /* for i.MX6ul */
|
