Searched full:mx28 (Results 1 – 25 of 48) sorted by relevance
12
| /Linux-v5.10/Documentation/devicetree/bindings/mfd/ |
| D | mxs-lradc.txt | 5 for i.MX28 SoC
13 disabled. 5 wires is valid for i.MX28 SoC only.
35 Example for i.MX28 SoC:
|
| /Linux-v5.10/Documentation/devicetree/bindings/clock/ |
| D | imx28-clock.yaml | 7 title: Clock bindings for Freescale i.MX28
14 ID in its "clocks" phandle cell. The following is a full list of i.MX28
|
| /Linux-v5.10/Documentation/devicetree/bindings/net/ |
| D | qca,qca7000.txt | 38 /* Freescale i.MX28 SPI master*/
75 /* Freescale i.MX28 UART */
|
| D | microchip,enc28j60.txt | 28 Example (for NXP i.MX28 with pin control stuff for GPIO irq):
|
| /Linux-v5.10/Documentation/devicetree/bindings/display/ |
| D | mxsfb.txt | 7 Should be "fsl,imx28-lcdif" for i.MX28.
43 Should be "fsl,imx28-lcdif" for i.MX28.
|
| /Linux-v5.10/drivers/clocksource/ |
| D | mxs_timer.c | 22 * The v1 on MX23 only gets 16 bits counter, while v2 on MX28
26 * another for clocksource. MX28 uses timrot 0 and 1, while MX23
43 * on MX28 while timrot2 on MX23.
|
| /Linux-v5.10/arch/arm/mach-mxs/ |
| D | Kconfig | 17 bool "Freescale MXS (i.MX23, i.MX28) support"
|
| /Linux-v5.10/drivers/gpu/drm/mxsfb/ |
| D | Kconfig | 20 i.MX28, i.MX6SX, i.MX7 and i.MX8M).
|
| D | mxsfb_drv.h | 5 * i.MX23/i.MX28/i.MX6SX MXSFB LCD controller driver.
|
| D | mxsfb_regs.h | 6 * i.MX23/i.MX28/i.MX6SX MXSFB LCD controller driver.
|
| /Linux-v5.10/Documentation/devicetree/bindings/rtc/ |
| D | stmp3xxx-rtc.txt | 1 * STMP3xxx/i.MX28 Time Clock controller
|
| /Linux-v5.10/arch/arm/boot/dts/ |
| D | mxs-pinfunc.h | 2 * Header providing constants for i.MX28 pinctrl bindings.
|
| D | imx28-ts4600.dts | 13 model = "Technologic Systems i.MX28 TS-4600";
|
| /Linux-v5.10/Documentation/devicetree/bindings/nvmem/ |
| D | mxs-ocotp.yaml | 7 title: On-Chip OTP Memory for Freescale i.MX23/i.MX28
|
| /Linux-v5.10/Documentation/devicetree/bindings/crypto/ |
| D | fsl-dcp.yaml | 7 title: Freescale DCP (Data Co-Processor) found on i.MX23/i.MX28
|
| /Linux-v5.10/Documentation/devicetree/bindings/spi/ |
| D | mxs-spi.yaml | 7 title: Freescale MX233/MX28 SSP/SPI
|
| /Linux-v5.10/Documentation/devicetree/bindings/mtd/ |
| D | gpmi-nand.yaml | 93 WARNING: on i.MX28 blockmark swapping cannot be disabled for the BootROM
|
| /Linux-v5.10/drivers/rtc/ |
| D | rtc-stmp3xxx.c | 124 int timeout = 5000; /* 3ms according to i.MX28 Ref Manual */ in stmp3xxx_wait_time()
126 * The i.MX28 Applications Processor Reference Manual, Rev. 1, 2010 in stmp3xxx_wait_time()
|
| /Linux-v5.10/drivers/i2c/busses/ |
| D | i2c-mxs.c | 107 * @dev_type: distinguish i.MX23/i.MX28 features
144 * For details, see i.MX233 [25.4.2 - 25.4.4] and i.MX28 [27.5.2 - 27.5.4]. in mxs_i2c_reset()
575 * The MX28 I2C IP block can only do PIO READ for transfer of to up in mxs_i2c_xfer_msg()
733 * The hardware (of the i.MX28 at least) seems to add 2 additional in mxs_i2c_derive_timing()
|
| /Linux-v5.10/include/linux/spi/ |
| D | mxs-spi.h | 5 * Freescale i.MX233/i.MX28 SPI controller register definition
|
| /Linux-v5.10/drivers/mtd/nand/raw/gpmi-nand/ |
| D | gpmi-regs.h | 168 /* MX28 uses this to detect READY. */
|
| /Linux-v5.10/drivers/nvmem/ |
| D | mxs-ocotp.c | 196 MODULE_DESCRIPTION("driver for OCOTP in i.MX23/i.MX28");
|
| D | Kconfig | 94 on the Freescale i.MX23/i.MX28 processor.
|
| /Linux-v5.10/Documentation/devicetree/bindings/pinctrl/ |
| D | fsl,mxs-pinctrl.txt | 124 Valid values for i.MX28/i.MX23 pinmux-id are defined in
|
| /Linux-v5.10/drivers/net/can/usb/kvaser_usb/ |
| D | kvaser_usb.h | 19 * - Leaf: Based on Renesas M32C or Freescale i.MX28, running firmware labeled
|
12
