Searched full:mx1 (Results 1 – 25 of 28) sorted by relevance
12
| /Linux-v6.1/Documentation/devicetree/bindings/clock/ |
| D | imx1-clock.yaml | 7 title: Clock bindings for Freescale i.MX1 CPUs
15 for the full list of i.MX1 clock IDs.
|
| /Linux-v6.1/drivers/clk/imx/ |
| D | clk-pllv1.c | 22 * PLL clock version 1, found on i.MX1/21/25/27/31/35
66 * frequency. PLLs with this register layout can be found on i.MX1, in clk_pllv1_recalc_rate()
84 * On all i.MXs except i.MX1 and i.MX21 mfn is a 10bit in clk_pllv1_recalc_rate()
|
| /Linux-v6.1/arch/arm/mach-imx/ |
| D | Kconfig | 61 bool "i.MX1 support"
66 This enables support for Freescale i.MX1 processor
|
| D | mach-imx1.c | 25 DT_MACHINE_START(IMX1_DT, "Freescale i.MX1 (Device Tree Support)")
|
| D | hardware.h | 40 * mx1:
|
| /Linux-v6.1/include/soc/imx/ |
| D | timer.h | 10 GPT_TYPE_IMX1, /* i.MX1 */
|
| /Linux-v6.1/Documentation/devicetree/bindings/pwm/ |
| D | imx-pwm.yaml | 18 Should be 2 for i.MX1 and 3 for i.MX27 and newer SoCs. See pwm.yaml
|
| /Linux-v6.1/arch/arm/boot/dts/ |
| D | imx1-ads.dts | 10 model = "Freescale MX1 ADS";
|
| D | imx1-pinfunc.h | 29 * 'pin' is an integer between 0 and 0xbf. i.MX1 has 4 ports with 32
|
| /Linux-v6.1/drivers/watchdog/ |
| D | imx2_wdt.c | 11 * NOTE: MX1 has a slightly different Watchdog than MX2 and later:
13 * MX1: MX2+:
|
| /Linux-v6.1/drivers/clocksource/ |
| D | timer-imx-gpt.c | 23 * - MX1/MXL
34 /* MX1, MX21, MX27 */
|
| /Linux-v6.1/Documentation/devicetree/bindings/bus/ |
| D | imx-weim.txt | 62 For i.MX1, i.MX21 ("fsl,imx1-weim") there are two
|
| /Linux-v6.1/drivers/soc/imx/ |
| D | soc-imx.c | 57 soc_id = "i.MX1"; in imx_soc_device_init()
|
| /Linux-v6.1/drivers/pwm/ |
| D | Kconfig | 232 tristate "i.MX1 PWM support"
236 Generic PWM framework driver for i.MX1 and i.MX21
|
| /Linux-v6.1/drivers/pinctrl/freescale/ |
| D | pinctrl-imx1.c | 3 // i.MX1 pinctrl driver based on imx pinmux core
|
| D | pinctrl-imx1-core.c | 36 * MX1 register offsets
|
| /Linux-v6.1/drivers/bus/ |
| D | imx-weim.c | 73 /* i.MX1/21 */
|
| /Linux-v6.1/drivers/mmc/host/ |
| D | mxcmmc.c | 6 * SoCs. It is basically the same hardware as found on MX1 (imxmmc.c).
7 * Unlike the hardware found on MX1, this hardware just works and does
|
| /Linux-v6.1/drivers/gpio/ |
| D | gpio-mxc.c | 250 /* MX1 and MX3 has one interrupt *per* gpio port */
|
| /Linux-v6.1/drivers/tty/serial/ |
| D | imx.c | 53 #define IMX1_UTS 0xd0 /* UART Test Register on i.mx1 */
77 #define IMX1_UCR1_UARTCLKEN (1<<2) /* UART clock enabled, i.mx1 only */
177 /* i.MX21 type uart runs on all i.mx except i.MX1 and i.MX6q */
2392 * Allocate the IRQ(s) i.MX1 has three interrupts whereas later in imx_uart_probe()
|
| /Linux-v6.1/drivers/dma/ |
| D | Kconfig | 269 Freescale i.MX1/21/27 chips.
|
| D | imx-dma.c | 6 // found on i.MX1/21/27
|
| /Linux-v6.1/drivers/mfd/ |
| D | sm501.c | 173 "M %ld.%ld (%ld), MX1 %ld.%ld (%ld)\n", in sm501_dump_clk()
182 "M %ld.%ld (%ld), MX1 %ld.%ld (%ld)\n", in sm501_dump_clk()
|
| /Linux-v6.1/arch/arm/ |
| D | Kconfig.debug | 421 bool "i.MX1 Debug UART"
425 on i.MX1.
|
| /Linux-v6.1/drivers/video/fbdev/ |
| D | imxfb.c | 516 * RMCR_LCDC_EN_MX1 is present on i.MX1 only, but doesn't hurt in imxfb_enable_controller()
|
12
