Searched full:lpsr (Results 1 – 11 of 11) sorted by relevance
| /Linux-v6.1/Documentation/devicetree/bindings/regulator/ |
| D | rohm,bd71815-regulator.yaml | 83 rohm,dvs-lpsr-voltage:
85 PMIC "LPSR" state voltage in uV when PMIC HW states are used. See
87 regulator should be disabled at LPSR state.
94 # (LPSR/SUSPEND). The voltage is automatically changed when HW
106 # for each of the HW states (RUN/SNVS/SUSPEND/LPSR). HW defaults can
|
| D | rohm,bd71828-regulator.yaml | 75 rohm,dvs-lpsr-voltage:
77 PMIC default "LPSR" state voltage in uV. See below table for
84 # buck | run | idle | suspend | lpsr
91 #(*) LPSR and SUSPEND states use same voltage but both states have own
|
| /Linux-v6.1/include/linux/mfd/ |
| D | rohm-generic.h | 49 * @lpsr_reg: register address for regulator config at 'lpsr' state
50 * @lpsr_mask: value mask for regulator voltages at 'lpsr' state
51 * @lpsr_on_mask: enable mask for regulator at 'lpsr' state
|
| /Linux-v6.1/drivers/rtc/ |
| D | rtc-snvs.c | 196 u32 lptar, lpsr; in snvs_rtc_read_alarm() local
206 regmap_read(data->regmap, data->offset + SNVS_LPSR, &lpsr); in snvs_rtc_read_alarm()
207 alrm->pending = (lpsr & SNVS_LPSR_LPTA) ? 1 : 0; in snvs_rtc_read_alarm()
270 u32 lpsr; in snvs_rtc_irq_handler() local
275 regmap_read(data->regmap, data->offset + SNVS_LPSR, &lpsr); in snvs_rtc_irq_handler()
277 if (lpsr & SNVS_LPSR_LPTA) { in snvs_rtc_irq_handler()
287 regmap_write(data->regmap, data->offset + SNVS_LPSR, lpsr); in snvs_rtc_irq_handler()
|
| /Linux-v6.1/Documentation/devicetree/bindings/pinctrl/ |
| D | fsl,imx7d-pinctrl.yaml | 21 - fsl,imx7d-iomuxc-lpsr
82 - fsl,imx7d-iomuxc-lpsr
104 compatible = "fsl,imx7d-iomuxc-lpsr";
|
| /Linux-v6.1/drivers/regulator/ |
| D | bd71815-regulator.c | 206 of_find_property(np, "rohm,dvs-lpsr-voltage", NULL) || in buck12_set_hw_dvs_levels()
219 * avoid shutting us down if LPSR or SUSPEND is set to in buck12_set_hw_dvs_levels()
341 * voltage is set to BD71815_REG_BUCK1_VOLT_H. Changing SUSPEND/LPSR in bd7181x_buck12_set_voltage_sel()
|
| D | bd71828-regulator.c | 117 "rohm,dvs-lpsr-voltage" }; in ldo6_parse_dt()
212 * LPSR voltage is same as SUSPEND voltage. Allow
214 * LPSR state
|
| D | rohm-regulator.c | 93 prop = "rohm,dvs-lpsr-voltage"; in rohm_regulator_set_dvs_levels()
|
| /Linux-v6.1/drivers/pinctrl/freescale/ |
| D | pinctrl-imx6ul.c | 297 /* pad for i.MX6ULL lpsr pinmux */
|
| D | pinctrl-imx7d.c | 371 { .compatible = "fsl,imx7d-iomuxc-lpsr", .data = &imx7d_lpsr_pinctrl_info },
|
| /Linux-v6.1/arch/arm/boot/dts/ |
| D | imx7s.dtsi | 451 compatible = "fsl,imx7d-iomuxc-lpsr";
|
