Searched full:initially (Results 1 – 25 of 638) sorted by relevance
12345678910>>...26
| /Linux-v6.6/Documentation/ABI/testing/ |
| D | sysfs-bus-counter | 94 The output signal is initially low, and will remain low
100 The output signal is initially high. The output signal
109 The output signal is initially high. When the counter
116 The output signal is initially high.
135 The output signal is initially high. When the count
141 The output signal is initially high. Counting is started
|
| D | sysfs-bus-vdpa | 6 to a driver after the creation. It initially contains 1, which
|
| /Linux-v6.6/include/linux/ |
| D | jump_label.h | 32 * define a "key" that is initially false via "DEFINE_STATIC_KEY_FALSE(key)",
35 * Similarly, we can define an initially true key via
39 * initially true or false can be using in both static_branch_unlikely()
47 * initially false key that is used in an "if (static_branch_unlikely(&key))"
96 * bit 0 => 1 if key is initially true
97 * 0 if initially false
|
| /Linux-v6.6/drivers/usb/cdns3/ |
| D | drd.h | 160 * 100 - Controller initially configured as Device
164 * 100 - Controller initially configured as Device.
|
| /Linux-v6.6/drivers/usb/storage/ |
| D | unusual_uas.h | 39 * Initially Reported-by: Julian Groß <julian.g@posteo.de>
157 * Initially Reported-by: Takeo Nakayama <javhera@gmx.com>
|
| /Linux-v6.6/drivers/soc/loongson/ |
| D | Kconfig | 16 SoCs. Initially only reading SVR and registering soc device are
|
| /Linux-v6.6/tools/perf/Documentation/ |
| D | perf-test.txt | 15 This command does assorted sanity tests, initially through linked routines but
|
| /Linux-v6.6/fs/jfs/ |
| D | jfs_extent.c | 111 /* allocate the disk blocks for the extent. initially, extBalloc() in extAlloc()
272 * initially, we will try to allocate disk blocks for the
308 /* get the number of blocks to initially attempt to allocate. in extBalloc()
|
| /Linux-v6.6/arch/arm/plat-orion/ |
| D | irq.c | 28 * Mask all interrupts initially. in orion_irq_init()
|
| /Linux-v6.6/drivers/android/ |
| D | Kconfig | 24 Each binderfs mount initially only contains a binder-control device.
|
| /Linux-v6.6/tools/testing/selftests/net/ |
| D | tcp_fastopen_backup_key.sh | 28 # initially present an old TFO cookie
|
| /Linux-v6.6/Documentation/gpu/rfc/ |
| D | i915_scheduler.rst | 30 * Initially only for GuC submission but execlists can be supported if
131 execbuf2 IOCTL can be called submitting N BBs in a single IOCTL. Initially only
|
| /Linux-v6.6/tools/testing/selftests/bpf/prog_tests/ |
| D | lookup_and_delete.c | 120 /* Fetched value should match the initially set value. */ in test_lookup_and_delete_hash()
159 /* Fetched value should match the initially set value. */ in test_lookup_and_delete_percpu_hash()
|
| /Linux-v6.6/drivers/soc/fsl/ |
| D | Kconfig | 19 Initially only reading SVR and registering soc device are supported.
|
| /Linux-v6.6/Documentation/devicetree/bindings/power/reset/ |
| D | gpio-poweroff.yaml | 31 Initially configure the GPIO line as an input. Only reconfigure
|
| /Linux-v6.6/security/smack/ |
| D | Kconfig | 25 of access initially with the bringup mode set on the
|
| /Linux-v6.6/net/dccp/ccids/ |
| D | Kconfig | 31 The TFRC congestion control algorithms were initially described in
|
| /Linux-v6.6/kernel/printk/ |
| D | printk_ringbuffer.h | 151 * Readers must see that the ringbuffer is initially empty.
156 * To satisfy Req1, the tail initially points to a descriptor that is
191 * initially there are no records to report the sequence number of
|
| /Linux-v6.6/drivers/irqchip/ |
| D | irq-vic.c | 75 /* we cannot allocate memory when VICs are initially registered */
410 /* Disable all interrupts initially. */ in vic_init_st()
463 /* Disable all interrupts initially. */ in __vic_init()
|
| /Linux-v6.6/tools/testing/selftests/mm/ |
| D | madv_populate.c | 175 "range initially not populated\n"); in test_populate_read()
197 "range initially not populated\n"); in test_populate_write()
|
| /Linux-v6.6/security/landlock/ |
| D | object.c | 61 * With @object->lock initially held, remove the reference from in landlock_put_object()
|
| /Linux-v6.6/include/sound/ |
| D | seq_oss.h | 27 /* note-on event passing mode: initially given by OSS seq,
|
| /Linux-v6.6/Documentation/scheduler/ |
| D | sched-debug.rst | 47 initially forks.
|
| /Linux-v6.6/include/linux/clk/ |
| D | analogbits-wrpll-cln28hpc.h | 53 * When initially passing a struct wrpll_cfg record, the
|
| /Linux-v6.6/arch/powerpc/include/asm/ |
| D | kprobes.h | 62 * Set in kprobes code, initially to 0. If the instruction can be
|
12345678910>>...26
