| /Linux-v6.1/drivers/platform/x86/ |
| D | gpd-pocket-fan.c | 1 // SPDX-License-Identifier: GPL-2.0+
3 * GPD Pocket fan controller driver
9 #include <linux/devm-helpers.h>
33 "Millicelsius values above which the fan speed increases");
38 "Hysteresis in millicelsius before lowering the fan speed");
43 "minimum fan speed to allow when system is powered by AC");
55 static void gpd_pocket_fan_set_speed(struct gpd_pocket_fan_data *fan, int speed) in gpd_pocket_fan_set_speed() argument
57 if (speed == fan->last_speed) in gpd_pocket_fan_set_speed()
60 gpiod_direction_output(fan->gpio0, !!(speed & 1)); in gpd_pocket_fan_set_speed()
61 gpiod_direction_output(fan->gpio1, !!(speed & 2)); in gpd_pocket_fan_set_speed()
[all …]
|
| /Linux-v6.1/Documentation/hwmon/ |
| D | g762.rst | 4 The GMT G762 Fan Speed PWM Controller is connected directly to a fan
5 and performs closed-loop or open-loop control of the fan speed. Two
6 modes - PWM or DC - are supported by the device.
9 http://natisbad.org/NAS/ref/GMT_EDS-762_763-080710-0.2.pdf. sysfs
10 bindings are described in Documentation/hwmon/sysfs-interface.rst.
19 fan revolution, ...); Those can be modified via devicetree bindings
25 set desired fan speed. This only makes sense in closed-loop
26 fan speed control (i.e. when pwm1_enable is set to 2).
29 provide current fan rotation value in RPM as reported by
30 the fan to the device.
[all …]
|
| D | nct6775.rst | 19 * Nuvoton NCT5572D/NCT6771F/NCT6772F/NCT6775F/W83677HG-I
87 Guenter Roeck <linux@roeck-us.net>
90 -----------
100 There are 4 to 5 fan rotation speed sensors, 8 to 15 analog voltage sensors,
102 fan regulation strategies (plus manual fan control mode).
113 Fan rotation speeds are reported in RPM (rotations per minute). An alarm is
114 triggered if the rotation speed has dropped below a programmable limit. On
115 NCT6775F, fan readings can be divided by a programmable divider (1, 2, 4, 8,
117 do not have a fan speed divider. The driver sets the most suitable fan divisor
118 itself; specifically, it increases the divider value each time a fan speed
[all …]
|
| D | adm9240.rst | 10 Addresses scanned: I2C 0x2c - 0x2f
20 Addresses scanned: I2C 0x2c - 0x2f
24 http://pdfserv.maxim-ic.com/en/ds/DS1780.pdf
30 Addresses scanned: I2C 0x2c - 0x2f
37 - Frodo Looijaard <frodol@dds.nl>,
38 - Philip Edelbrock <phil@netroedge.com>,
39 - Michiel Rook <michiel@grendelproject.nl>,
40 - Grant Coady <gcoady.lk@gmail.com> with guidance
44 ---------
46 chip MSB 5-bit address. Each chip reports a unique manufacturer
[all …]
|
| D | g760a.rst | 6 * Global Mixed-mode Technology Inc. G760A
12 http://www.gmt.com.tw/product/datasheet/EDS-760A.pdf
17 -----------
19 The GMT G760A Fan Speed PWM Controller is connected directly to a fan
20 and performs closed-loop control of the fan speed.
22 The fan speed is programmed by setting the period via 'pwm1' of two
23 consecutive speed pulses. The period is defined in terms of clock
26 Setting a period of 0 stops the fan; setting the period to 255 sets
27 fan to maximum speed.
29 The measured fan rotation speed returned via 'fan1_input' is derived
[all …]
|
| D | w83792d.rst | 10 Addresses scanned: I2C 0x2c - 0x2f
19 -----------------
35 -----------
42 parameter; this will put it into a more well-behaved state first.
44 The driver implements three temperature sensors, seven fan rotation speed
45 sensors, nine voltage sensors, and two automatic fan regulation
46 strategies called: Smart Fan I (Thermal Cruise mode) and Smart Fan II.
48 The driver also implements up to seven fan control outputs: pwm1-7. Pwm1-7
53 Automatic fan control mode is possible only for fan1-fan3.
55 For all pwmX outputs, a value of 0 means minimum fan speed and a value of
[all …]
|
| D | dell-smm-hwmon.rst | 1 .. SPDX-License-Identifier: GPL-2.0-or-later
5 Kernel driver dell-smm-hwmon
8 :Copyright: |copy| 2002-2005 Massimo Dal Zotto <dz@debian.org>
12 -----------
18 automatically adjust fan speed (please notice that it currently uses
24 -------------------
35 fan[1-3]_input RO Fan speed in RPM.
36 fan[1-3]_label RO Fan label.
37 fan[1-3]_min RO Minimal Fan speed in RPM
38 fan[1-3]_max RO Maximal Fan speed in RPM
[all …]
|
| D | dme1737.rst | 18 Addresses scanned: none, address read from Super-I/O config space
34 Addresses scanned: none, address read from Super-I/O config space
43 -----------------
46 Enables the monitoring of voltage, fan and temp inputs
52 Include non-standard LPC addresses 0x162e and 0x164e
55 - VIA EPIA SN18000
59 -----------
63 and SCH5127 Super-I/O chips. These chips feature monitoring of 3 temp sensors
64 temp[1-3] (2 remote diodes and 1 internal), 8 voltages in[0-7] (7 external and
65 1 internal) and up to 6 fan speeds fan[1-6]. Additionally, the chips implement
[all …]
|
| D | w83627ehf.rst | 22 * Winbond W83627DHG-P
46 * Winbond W83667HG-B
54 * Nuvoton NCT6775F/W83667HG-I
73 - Jean Delvare <jdelvare@suse.de>
74 - Yuan Mu (Winbond)
75 - Rudolf Marek <r.marek@assembler.cz>
76 - David Hubbard <david.c.hubbard@gmail.com>
77 - Gong Jun <JGong@nuvoton.com>
80 -----------
83 W83627DHG, W83627DHG-P, W83627UHG, W83667HG, W83667HG-B, W83667HG-I
[all …]
|
| D | adm1026.rst | 16 - Philip Pokorny <ppokorny@penguincomputing.com> for Penguin Computing
17 - Justin Thiessen <jthiessen@penguincomputing.com>
20 -----------------
23 List of GPIO pins (0-16) to program as inputs
26 List of GPIO pins (0-16) to program as outputs
29 List of GPIO pins (0-16) to program as inverted
32 List of GPIO pins (0-16) to program as normal/non-inverted
35 List of GPIO pins (0-7) to program as fan tachs
39 -----------
45 16 general purpose digital I/O lines, eight (8) fan speed sensors (8-bit),
[all …]
|
| D | f71882fg.rst | 103 This is the 64-pin variant of the F71889FG, they have the
119 -----------
125 These chips also have fan controlling features, using either DC or PWM, in
133 ----------
135 The Voltage, Fan and Temperature Monitoring uses the standard sysfs
136 interface as documented in sysfs-interface, without any exceptions.
139 Fan Control
140 -----------
142 Both PWM (pulse-width modulation) and DC fan speed control methods are
149 vica versa. So the temperature zone trip points 1-4 (or 1-2) go from high temp
[all …]
|
| D | adt7470.rst | 17 -----------
22 The ADT7470 uses the 2-wire interface compatible with the SMBus 2.0
24 external temperatures. It has four (4) 16-bit counters for measuring fan speed.
25 There are four (4) PWM outputs that can be used to control fan speed.
28 that allows fan speed to be adjusted automatically based on any of the ten
34 Each of the measured inputs (temperature, fan speed) has corresponding high/low
40 automatic fan pwm control to set the fan speed. The driver will not read the
45 ----------------
47 The ADT7470 has a 8-bit ADC and is capable of measuring temperatures with 1
54 -------------------
[all …]
|
| D | lm63.rst | 45 -----------
47 The LM63 is a digital temperature sensor with integrated fan monitoring
50 The LM63 is basically an LM86 with fan speed monitoring and control
53 - No low limit for local temperature.
54 - No critical limit for local temperature.
55 - Critical limit for remote temperature can be changed only once. We
56 will consider that the critical limit is read-only.
66 The fan speed is measured using a tachometer. Contrary to most chips which
67 store the value in an 8-bit register and have a selectable clock divider
68 to make sure that the result will fit in the register, the LM63 uses 16-bit
[all …]
|
| D | adt7475.rst | 39 - Jordan Crouse
40 - Hans de Goede
41 - Darrick J. Wong (documentation)
42 - Jean Delvare
46 -----------
56 The ADT747x uses the 2-wire interface compatible with the SMBus 2.0
58 temperatures and two (2) or more voltages. It has four (4) 16-bit counters
59 for measuring fan speed. There are three (3) PWM outputs that can be used
60 to control fan speed.
63 ADT747x that allows fan speed to be adjusted automatically based on any of the
[all …]
|
| D | it87.rst | 158 - Christophe Gauthron
159 - Jean Delvare <jdelvare@suse.de>
163 -----------------
176 misconfigured by BIOS - PWM values would be inverted. This option tries
181 -------------------
183 All the chips supported by this driver are LPC Super-I/O chips, accessed
184 through the LPC bus (ISA-like I/O ports). The IT8712F additionally has an
192 -----------
201 include an 'environment controller' with 3 temperature sensors, 3 fan
202 rotation speed sensors, 8 voltage sensors, associated alarms, and chassis
[all …]
|
| /Linux-v6.1/Documentation/driver-api/thermal/ |
| D | nouveau_thermal.rst | 12 -----------
14 This driver allows to read the GPU core temperature, drive the GPU fan and
17 Currently, due to the absence of in-kernel API to access HWMON drivers, Nouveau
19 have one of those, temperature and/or fan management through Nouveau's HWMON
24 ----------------------
26 Temperature is exposed under as a read-only HWMON attribute temp1_input.
32 Fan speed is set to 100% when reaching this temperature;
55 Fan management
56 --------------
58 Not all cards have a drivable fan. If you do, then the following HWMON
[all …]
|
| /Linux-v6.1/Documentation/admin-guide/acpi/ |
| D | fan_performance_states.rst | 1 .. SPDX-License-Identifier: GPL-2.0
4 ACPI Fan Performance States
8 fan (for example, PNP0C0B or INT3404), the ACPI fan driver creates additional
10 These attributes list properties of fan performance states.
19 $ ls -l /sys/bus/acpi/devices/INT3404:00/
22 -r--r--r-- 1 root root 4096 Dec 13 20:38 state0
23 -r--r--r-- 1 root root 4096 Dec 13 20:38 state1
24 -r--r--r-- 1 root root 4096 Dec 13 20:38 state10
25 -r--r--r-- 1 root root 4096 Dec 13 20:38 state11
26 -r--r--r-- 1 root root 4096 Dec 13 20:38 state2
[all …]
|
| /Linux-v6.1/drivers/macintosh/ |
| D | therm_adt746x.c | 1 // SPDX-License-Identifier: GPL-2.0-only
53 static int fan_speed = -1;
66 MODULE_PARM_DESC(fan_speed,"Specify starting fan speed (0-255) "
90 static void write_both_fan_speed(struct thermostat *th, int speed);
91 static void write_fan_speed(struct thermostat *th, int speed, int fan);
101 rc = i2c_master_send(th->clt, (const char *)tmp, 2); in write_reg()
105 return -ENODEV; in write_reg()
116 rc = i2c_master_send(th->clt, ®_addr, 1); in read_reg()
120 return -ENODEV; in read_reg()
121 rc = i2c_master_recv(th->clt, (char *)&data, 1); in read_reg()
[all …]
|
| /Linux-v6.1/Documentation/devicetree/bindings/hwmon/ |
| D | gpio-fan.txt | 1 Bindings for fan connected to GPIO lines
4 - compatible : "gpio-fan"
7 - gpios: Specifies the pins that map to bits in the control value,
8 ordered MSB-->LSB.
9 - gpio-fan,speed-map: A mapping of possible fan RPM speeds and the
12 - alarm-gpios: This pin going active indicates something is wrong with
13 the fan, and a udev event will be fired.
14 - #cooling-cells: If used as a cooling device, must be <2>
16 Documentation/devicetree/bindings/thermal/thermal-cooling-devices.yaml
17 min and max states are derived from the speed-map of the fan.
[all …]
|
| /Linux-v6.1/drivers/hwmon/ |
| D | aquacomputer_d5next.c | 1 // SPDX-License-Identifier: GPL-2.0+
85 /* Pump and fan speed registers in D5 Next control report (from 0-100%) */
98 /* Register offsets for the Octo fan controller */
108 /* Fan speed registers in Octo control report (from 0-100%) */
111 /* Register offsets for the Quadro fan controller */
122 /* Fan speed registers in Quadro control report (from 0-100%) */
141 "Pump speed",
142 "Fan speed"
147 "Fan power"
152 "Fan voltage",
[all …]
|
| D | g762.c | 1 // SPDX-License-Identifier: GPL-2.0-or-later
3 * g762 - Driver for the Global Mixed-mode Technology Inc. fan speed
15 * http://natisbad.org/NAS/refs/GMT_EDS-762_763-080710-0.2.pdf
27 * http://www.gmt.com.tw/product/datasheet/EDS-762_3.pdf
36 #include <linux/hwmon-sysfs.h>
67 #define G762_REG_FAN_CMD1_FAN_MODE 0x10 /* fan mode: closed/open-loop */
71 #define G762_REG_FAN_CMD1_PULSE_PER_REV 0x01 /* pulse per fan revolution */
73 #define G762_REG_FAN_CMD2_GEAR_MODE_1 0x08 /* fan gear mode */
75 #define G762_REG_FAN_CMD2_FAN_STARTV_1 0x02 /* fan startup voltage */
78 #define G762_REG_FAN_STA_FAIL 0x02 /* fan fail */
[all …]
|
| D | dell-smm-hwmon.c | 1 // SPDX-License-Identifier: GPL-2.0-or-later
3 * dell-smm-hwmon.c -- Linux driver for accessing the SMM BIOS on Dell laptops.
9 * Copyright (C) 2013, 2014 Guenter Roeck <linux@roeck-us.net>
84 bool fan[DELL_SMM_NO_FANS]; member
111 MODULE_PARM_DESC(restricted, "Restrict fan control and serial number to CAP_SYS_ADMIN (default: 1)"…
120 MODULE_PARM_DESC(fan_mult, "Factor to multiply fan speed with (default: autodetect)");
124 MODULE_PARM_DESC(fan_max, "Maximum configurable fan speed (default: autodetect)");
145 "Processor Fan",
146 "Motherboard Fan",
147 "Video Fan",
[all …]
|
| D | gpio-fan.c | 1 // SPDX-License-Identifier: GPL-2.0-or-later
3 * gpio-fan.c - Hwmon driver for fans connected to GPIO lines.
38 struct gpio_fan_speed *speed; member
55 sysfs_notify(&fan_data->hwmon_dev->kobj, NULL, "fan1_alarm"); in fan_alarm_notify()
56 kobject_uevent(&fan_data->hwmon_dev->kobj, KOBJ_CHANGE); in fan_alarm_notify()
63 schedule_work(&fan_data->alarm_work); in fan_alarm_irq_handler()
74 gpiod_get_value_cansleep(fan_data->alarm_gpio)); in fan1_alarm_show()
82 struct device *dev = fan_data->dev; in fan_alarm_init()
88 alarm_irq = gpiod_to_irq(fan_data->alarm_gpio); in fan_alarm_init()
92 INIT_WORK(&fan_data->alarm_work, fan_alarm_notify); in fan_alarm_init()
[all …]
|
| /Linux-v6.1/drivers/gpu/drm/nouveau/nvkm/subdev/therm/ |
| D | fan.c | 27 #include <subdev/bios/fan.h>
32 nvkm_fan_update(struct nvkm_fan *fan, bool immediate, int target) in nvkm_fan_update() argument
34 struct nvkm_therm *therm = fan->parent; in nvkm_fan_update()
35 struct nvkm_subdev *subdev = &therm->subdev; in nvkm_fan_update()
36 struct nvkm_timer *tmr = subdev->device->timer; in nvkm_fan_update()
41 /* update target fan speed, restricting to allowed range */ in nvkm_fan_update()
42 spin_lock_irqsave(&fan->lock, flags); in nvkm_fan_update()
44 target = fan->percent; in nvkm_fan_update()
45 target = max_t(u8, target, fan->bios.min_duty); in nvkm_fan_update()
46 target = min_t(u8, target, fan->bios.max_duty); in nvkm_fan_update()
[all …]
|
| /Linux-v6.1/drivers/gpu/drm/amd/pm/powerplay/hwmgr/ |
| D | vega10_thermal.c | 42 if (hwmgr->thermal_controller.fanInfo.bNoFan) in vega10_fan_ctrl_get_fan_speed_info()
45 fan_speed_info->supports_percent_read = true; in vega10_fan_ctrl_get_fan_speed_info()
46 fan_speed_info->supports_percent_write = true; in vega10_fan_ctrl_get_fan_speed_info()
47 fan_speed_info->min_percent = 0; in vega10_fan_ctrl_get_fan_speed_info()
48 fan_speed_info->max_percent = 100; in vega10_fan_ctrl_get_fan_speed_info()
51 hwmgr->thermal_controller.fanInfo. in vega10_fan_ctrl_get_fan_speed_info()
53 fan_speed_info->supports_rpm_read = true; in vega10_fan_ctrl_get_fan_speed_info()
54 fan_speed_info->supports_rpm_write = true; in vega10_fan_ctrl_get_fan_speed_info()
55 fan_speed_info->min_rpm = in vega10_fan_ctrl_get_fan_speed_info()
56 hwmgr->thermal_controller.fanInfo.ulMinRPM; in vega10_fan_ctrl_get_fan_speed_info()
[all …]
|
