Searched full:depending (Results 1 – 25 of 2119) sorted by relevance
12345678910>>...85
| /Linux-v6.1/Documentation/hwmon/ |
| D | gsc-hwmon.rst | 21 The voltage inputs are scaled either internally or by the driver depending
33 either internally or by the driver depending on the GSC version and firmware.
44 PWM value will be scalled depending on 6 temperature boundaries.
|
| D | adm1275.rst | 103 inX_label "vin1" or "vout1" depending on chip variant and
118 curr1_lcrit Critical minimum current. Depending on the chip
122 curr1_crit Critical maximum current. Depending on the chip
|
| D | nct6775.rst | 97 PCH, and SMBUS. Depending on the chip type, 2 to 6 of the temperature sources
108 either 1 degC or 0.5 degC, depending on the temperature source and
111 value. Alarms are only supported for temp1 to temp6, depending on the chip type.
245 There are up to seven data points depending on the chip type. Subsequent data
|
| D | ltc2945.rst | 56 SENSE+ or VDD pin depending on chip configuration.
84 voltage or ADIN voltage depending on chip configuration.
|
| /Linux-v6.1/drivers/mtd/spi-nor/ |
| D | Kconfig | 17 Many flash memories support erasing small (4096 B) sectors. Depending
37 Depending on the flash chip this either clears the block protection
54 If the software write protection will be disabled depending on
|
| /Linux-v6.1/Documentation/driver-api/thermal/ |
| D | nouveau_thermal.rst | 41 Some of these thresholds may not be used by Nouveau depending
79 * 2; The fan is driven automatically depending on the temperature.
87 depending on your hardware.
|
| /Linux-v6.1/include/uapi/linux/ |
| D | falloc.h | 22 * smaller depending on the filesystem and/or the configuration of the
53 * boundaries, but this boundary may be larger or smaller depending on
71 * depending on the filesystem and/or the configuration of the filesystem
|
| /Linux-v6.1/Documentation/PCI/endpoint/function/binding/ |
| D | pci-test.rst | 22 msi_interrupts Should be 1 to 32 depending on the number of MSI interrupts
24 msix_interrupts Should be 1 to 2048 depending on the number of MSI-X
|
| /Linux-v6.1/include/linux/ |
| D | iosys-map.h | 16 * When accessing a memory region, depending on its location, users may have to
89 * buffer memory. Depending on the location of the memory, the provided helpers
229 * Depending on the state of struct iosys_map.is_iomem, tests if the
246 * Depending on the state of struct iosys_map.is_iomem, tests if the
283 * system memory. Depending on the buffer's location, the helper picks the
303 * system memory. Depending on the mapping location, the helper picks the
320 * Increments the address stored in a iosys mapping. Depending on the
338 * Set value in iosys_map. Depending on the buffer's location, the helper
|
| /Linux-v6.1/Documentation/ABI/testing/ |
| D | sysfs-bus-iio-adc-hi8435 | 18 Depending on in_voltageY_sensing_mode the low voltage threshold
37 Depending on in_voltageY_sensing_mode the high voltage threshold
|
| /Linux-v6.1/Documentation/sound/soc/ |
| D | clocking.rst | 18 their speed can be altered by software (depending on the system use and to save
39 it is best to configure BCLK to the lowest possible speed (depending on your
|
| D | pops-clicks.rst | 12 depending on the audio usage and this can subsequently cause a small pop or
39 playback in that components are powered in a sequence depending upon stream
|
| D | dai.rst | 30 usually varies depending on the sample rate and the master system clock
53 receive the audio data. Bit clock usually varies depending on sample rate
|
| D | jack.rst | 41 These represent a DAPM pin to update depending on some of the status
69 These are all hooked together by the machine driver depending on the
|
| /Linux-v6.1/Documentation/devicetree/bindings/interconnect/ |
| D | interconnect.txt | 15 depending on the use case. Interconnect providers can also be interconnect
42 multiple paths from different providers depending on use case and the
|
| /Linux-v6.1/arch/arm/include/asm/ |
| D | kasan_def.h | 68 * The KASAN_SHADOW_OFFSET is provided in a Kconfig option depending
71 * the shadow offset depending on this.
|
| /Linux-v6.1/Documentation/netlabel/ |
| D | lsm_interface.rst | 26 low-level packet label depending on the NetLabel build time and run time
43 Depending on the exact configuration, translation between the network packet
|
| /Linux-v6.1/security/selinux/ss/ |
| D | conditional.h | 42 * depending on the current value of the conditional expression. This
53 * two lists of rules to enable/disable depending on the value of the
|
| /Linux-v6.1/Documentation/admin-guide/media/ |
| D | saa7134.rst | 52 Depending on the card you might have to pass ``card=<nr>`` as insmod option.
82 default might not work for you depending on which version you have.
|
| /Linux-v6.1/Documentation/devicetree/bindings/regulator/ |
| D | palmas-pmic.txt | 35 For ti,palmas-pmic - smps12, smps123, smps3 depending on OTP,
36 smps45, smps457, smps7 depending on variant, smps6, smps[8-9],
|
| /Linux-v6.1/Documentation/misc-devices/ |
| D | apds990x.rst | 26 might vary quite much depending the spectrum of the light source.
68 to saturate much before that. Real max value varies depending
|
| /Linux-v6.1/Documentation/sound/hd-audio/ |
| D | realtek-pc-beep.rst | 42 When zero, mix 1Ah (possibly with amplification, depending on L and R bits)
47 When one, mix 1Ah (possibly with amplification, depending on L and R bits)
97 generator and external PCBEEP pin, depending on if the beep generator is
|
| /Linux-v6.1/arch/arm/mach-s3c/ |
| D | map-s3c64xx.h | 19 * These may be used by SROM, NAND or CF depending on settings
57 (depending on SoC POP version) */
|
| /Linux-v6.1/Documentation/userspace-api/media/v4l/ |
| D | tuner.rst | 15 depending on the number of RF connectors on the tuner. The ``type``
47 video outputs, depending on the number of RF connectors on the
|
| /Linux-v6.1/drivers/staging/media/deprecated/saa7146/av7110/ |
| D | Kconfig | 31 or /lib/firmware (depending on configuration of firmware hotplug).
101 or /lib/firmware (depending on configuration of firmware hotplug).
|
12345678910>>...85
