Searched full:bucks (Results 1 – 25 of 37) sorted by relevance
12
| /Linux-v5.15/Documentation/devicetree/bindings/regulator/ |
| D | rohm,bd71815-regulator.yaml | 56 comments below for bucks/LDOs which support this. 0 means
76 comments below for bucks/LDOs which support this. 0 means
85 comments below for bucks/LDOs which support this. 0 means
91 # Bucks 1 and 2 support giving separate voltages for operational states
94 # state changes. Omitting these properties from bucks 1 and 2 leave
98 # Bucks 3-5 and ldos 1-5 support setting the RUN state voltage here.
108 # that setting non zero voltages for bucks 1/2 will also enable voltage
|
| D | rohm,bd71828-regulator.yaml | 54 bucks which support this. 0 means disabled.
62 bucks which support this. 0 means disabled.
70 bucks which support this. 0 means disabled.
78 bucks which support this. 0 means disabled.
|
| D | samsung,s2mpa01.txt | 34 Note: Some bucks share the ramp rate setting i.e. same ramp value
35 will be set for a particular group of bucks so provide the same
|
| D | rohm,bd71847-regulator.yaml | 62 bucks which support this. 0 means disabled.
70 bucks which support this. 0 means disabled.
78 bucks which support this. 0 means disabled.
|
| D | rohm,bd71837-regulator.yaml | 63 bucks which support this. 0 means disabled.
71 bucks which support this. 0 means disabled.
79 bucks which support this. 0 means disabled.
|
| D | samsung,s2mps11.txt | 43 Note: On S2MPS11 some bucks share the ramp rate setting i.e. same ramp value
44 will be set for a particular group of bucks so provide the same
|
| D | max77802.txt | 47 -BUCKn : for BUCKs, where n can lie in range 1 to 10.
68 are: BUCKs 2-4 and LDOs 1-35. Also, it only takes effect if the regulator has
|
| D | max8997-regulator.txt | 45 multiple bucks, changing the voltage value of one of the bucks may affect
|
| D | mt6315-regulator.yaml | 14 that contains 4 BUCKs output which can combine with each other
|
| D | max77686.txt | 26 -BUCKn : for BUCKs, where n can lie in range 1 to 9.
|
| /Linux-v5.15/Documentation/devicetree/bindings/mfd/ |
| D | da9062.txt | 11 da9062-regulator : : LDOs & BUCKs
22 da9062-regulator : : LDOs & BUCKs
53 - regulators : This node defines the settings for the LDOs and BUCKs.
|
| D | da9063.txt | 7 da9063-regulator : : LDOs & BUCKs
24 - regulators : This node defines the settings for the LDOs and BUCKs.
|
| /Linux-v5.15/drivers/regulator/ |
| D | max77802-regulator.c | 256 /* BUCKS 1, 6 */
270 /* BUCKs 2-4 */
285 /* BUCKs 5, 7-10 */
340 /* BUCKs 1, 6 */
365 /* BUCKS 2-4 */
412 /* BUCKs 7-10 */
|
| D | Kconfig | 275 Say y here to support the BUCKs and LDOs regulators found on
289 Say y here to support the BUCKs and LDOs regulators found on
299 Say y here to support the BUCKs and LDOs regulators found on
309 Say y here to support the BUCKs and LDOs regulators found on
405 21 general purpose LDOs, 3 dedicated LDOs, and 5 BUCKs. All
1094 via I2C bus. S2MPA01 has 10 Bucks and 26 LDO outputs.
1110 via I2C bus. S5M8767A have 9 Bucks and 28 LDOs output and
|
| D | da9063-regulator.c | 32 /* BUCKs */
44 /* When two BUCKs are merged, they cannot be reused separately */
107 /* Macros for voltage DC/DC converters (BUCKs) */
229 * Bucks use single mode register field for normal operation
841 "Error while reading BUCKs configuration\n"); in da9063_regulator_probe()
|
| D | bd718x7-regulator.c | 130 * Bucks 1 to 4 support DVS. PWM mode is used when voltage is changed.
131 * Bucks 5 to 8 and LDOs can use PFM and must be disabled when voltage
664 * BD71837 bucks 3 and 4 support defining their enable/disable state also
692 * bucks/LDOs which are controlled via register interface are changed.
694 * beginning of shut-down sequence. As bucks 6 and 7 are parent
1536 * - hence I keep the DVS disabled for non DVS bucks by default. I don't want
|
| D | max77686-regulator.c | 42 * Values used for configuring LDOs and bucks.
112 /* Some BUCKs and LDOs supports Normal[ON/OFF] mode during suspend */
|
| D | hi6421v530-regulator.c | 23 * @mode_mask: ECO mode bitmask of LDOs; for BUCKs, this masks sleep
|
| D | lp87565-regulator.c | 117 /* Operations permitted on BUCKs */
|
| D | hi6421-regulator.c | 35 * @mode_mask: ECO mode bitmask of LDOs; for BUCKs, this masks sleep
374 * more LDO or BUCKs simultaneously, or it may burn the chip. in hi6421_regulator_enable()
|
| D | bd71815-regulator.c | 184 * Bucks 1 and 2 have two voltage selection registers where selected
340 * If bucks 1 & 2 are controlled by state machine - then the RUN state in bd7181x_buck12_set_voltage_sel()
|
| D | mt6380-regulator.c | 80 * @vselon_reg: Register sections for hardware control mode of bucks
|
| /Linux-v5.15/include/linux/mfd/ |
| D | 88pm80x.h | 54 #define PM800_MAX_REGULATOR PM800_ID_RG_MAX /* 5 Bucks, 19 LDOs */
55 #define PM800_NUM_BUCK (5) /*5 Bucks */
56 #define PM800_NUM_LDO (19) /*19 Bucks */
|
| /Linux-v5.15/Documentation/devicetree/bindings/usb/ |
| D | mediatek,mt6360-tcpc.yaml | 14 regulators (BUCKs/LDOs), and TypeC Port Switch with Power Delivery controller.
|
| /Linux-v5.15/drivers/mfd/ |
| D | lp8788.c | 71 /* 4 bucks */
|
12
