| /Linux-v6.1/Documentation/devicetree/bindings/mfd/ |
| D | max8998.txt | 26 - max8998,pmic-buck1-dvs-gpios: GPIO specifiers for two host gpios used
32 - max8998,pmic-buck1-default-dvs-idx: Default voltage setting selected from
43 Additional properties required if max8998,pmic-buck1-dvs-gpios is defined:
44 - max8998,pmic-buck1-dvs-voltage: An array of 4 voltage values in microvolts
45 for buck1 regulator that can be selected using dvs gpio.
68 - Example: BUCK1, BUCK2, BUCK3, BUCK4
91 max8998,pmic-buck1-default-dvs-idx = <0>;
92 max8998,pmic-buck1-dvs-gpios = <&gpx0 0 1 0 0>, /* SET1 */
94 max8998,pmic-buck1-dvs-voltage = <1350000>, <1300000>,
111 buck1_reg: BUCK1 {
|
| D | ti,lp87524-q1.yaml | 43 - buck1
59 - buck1-in-supply
80 buck1-in-supply = <&vdd_5v0>;
92 buck1_reg: buck1 {
93 regulator-name = "buck1";
|
| D | lp873x.txt | 12 buck0, buck1, ldo0 or ldo1.
24 buck1-in-supply = <&vsys_3v3>;
40 lp8733_buck1: buck1 {
41 regulator-name = "lp8733-buck1";
|
| D | da9055.txt | 33 buck1 : regulator BUCK1
57 buck1: BUCK1 {
|
| D | da9062.txt | 56 buck1 : BUCK_1
67 buck1 : BUCK_1
106 DA9062_BUCK1: buck1 {
107 regulator-name = "BUCK1";
|
| D | richtek,rt5120.yaml | 50 description: phandle for buck1 input power source
133 buck1 {
134 regulator-name = "rt5120-buck1";
|
| /Linux-v6.1/Documentation/devicetree/bindings/regulator/ |
| D | maxim,max8997.yaml | 33 max8997,pmic-buck1-dvs-voltage:
38 A set of 8 voltage values in micro-volt (uV) units for buck1 when
69 max8997,pmic-buck1-uses-gpio-dvs:
72 buck1 can be controlled by GPIO DVS.
247 - max8997,pmic-buck1-dvs-voltage
254 max8997,pmic-buck1-uses-gpio-dvs: [ 'max8997,pmic-buck125-dvs-gpios' ]
263 - max8997,pmic-buck1-uses-gpio-dvs
270 max8997,pmic-buck1-dvs-voltage:
296 max8997,pmic-buck1-uses-gpio-dvs;
307 max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>,
[all …]
|
| D | nxp,pca9450-regulator.yaml | 21 #BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6,
23 #Note: Buck3 removed on PCA9450B and connect with Buck1 on PCA9450C.
64 PMIC default "RUN" state voltage in uV. Only Buck1~3 have such
72 PMIC default "STANDBY" state voltage in uV. Only Buck1~3 have such
118 buck1: BUCK1 {
119 regulator-name = "BUCK1";
|
| D | lp872x.txt | 20 bit[2]: BUCK1 output voltage control by external DVS pin or register
23 bit[0]: BUCK1 enable control, 1 = enable, 0 = disable
35 LP8725 has maximum 9 nodes. (child name: ldo1 ~ 5, lilo1,2 and buck1,2)
101 /* Enable BUCK1,2, no DVS, normal LDO mode, timestep is 256usec */
144 vcc1: buck1 {
|
| D | mt6360-regulator.yaml | 14 after their hardware counterparts buck1/2 or ldo1/2/3/5/6/7
46 buck1 {
47 regulator-compatible = "BUCK1";
48 regulator-name = "mt6360,buck1";
|
| D | richtek,rt5190a-regulator.yaml | 61 regulator description for buck1 to buck4, and ldo.
66 buck operating mode, only buck1/4 support mode operating.
107 rt5190_buck1: buck1 {
108 regulator-name = "rt5190a-buck1";
|
| D | pv88080.txt | 17 BUCK1, BUCK2, BUCK3 and HVBUCK.
31 BUCK1 {
32 regulator-name = "buck1";
|
| D | pv88090.txt | 11 BUCK1, BUCK2, BUCK3, LDO1, and LDO2.
25 BUCK1 {
26 regulator-name = "buck1";
|
| D | 88pg86x.txt | 7 Optional subnodes for regulators: "buck1", "buck2", using common regulator
16 vcpu: buck1 {
|
| D | pv88060.txt | 11 BUCK1, LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7, SW1, SW2, SW3, SW4,
26 BUCK1 {
27 regulator-name = "buck1";
|
| D | 88pm800.txt | 14 buck1, buck2, buck3, buck4, buck5, ldo1, ldo2, ldo3, ldo4, ldo5, ldo6, ldo7,
24 buck1 {
|
| D | dlg,da9121.yaml | 145 DA9121_BUCK1: buck1 {
146 regulator-name = "BUCK1";
176 DA9122_BUCK1: buck1 {
177 regulator-name = "BUCK1";
|
| /Linux-v6.1/arch/arm64/boot/dts/freescale/ |
| D | imx8mn-ddr3l-evk.dts | 15 cpu-supply = <&buck1>;
19 cpu-supply = <&buck1>;
23 cpu-supply = <&buck1>;
27 cpu-supply = <&buck1>;
40 buck1: BUCK1 { label
|
| D | imx8mp-icore-mx8mp.dtsi | 43 buck1: BUCK1 { label
48 regulator-name = "BUCK1";
|
| /Linux-v6.1/include/linux/mfd/ |
| D | max8998.h | 64 * registers set by buck?_voltage?. The voltage of BUCK1/2 cannot
66 * @buck1_voltage: BUCK1 DVS mode 1 voltage registers
68 * @buck1_set1: BUCK1 gpio pin 1 to set output voltage
69 * @buck1_set2: BUCK1 gpio pin 2 to set output voltage
70 * @buck1_default_idx: Default for BUCK1 gpio pin 1, 2
|
| /Linux-v6.1/arch/arm/boot/dts/ |
| D | dra71-evm.dts | 87 buck1-in-supply =<&vsys_3v3>;
93 /* FB_B0 -> LP8733-BUCK1 - VPO_S1_AVS - VDD_CORE_AVS (core, mpu, gpu) */
101 lp8733_buck1_reg: buck1 {
103 regulator-name = "lp8733-buck1";
135 buck1-in-supply =<&vsys_3v3>;
141 /* FB_B0 -> LP8732-BUCK1 - VPO_S3_1V8 - VDDS_1V8 */
149 lp8732_buck1_reg: buck1 {
151 regulator-name = "lp8732-buck1";
|
| /Linux-v6.1/drivers/regulator/ |
| D | tps65219-regulator.c | 50 { "BUCK1_SCG", "BUCK1", "short circuit to ground", REGULATOR_EVENT_REGULATION_OUT },
51 { "BUCK1_OC", "BUCK1", "overcurrent", REGULATOR_EVENT_OVER_CURRENT },
52 { "BUCK1_NEG_OC", "BUCK1", "negative overcurrent", REGULATOR_EVENT_OVER_CURRENT },
53 { "BUCK1_UV", "BUCK1", "undervoltage", REGULATOR_EVENT_UNDER_VOLTAGE },
58 { "BUCK1_RV", "BUCK1", "residual voltage", REGULATOR_EVENT_OVER_VOLTAGE_WARN },
65 { "BUCK1_RV_SD", "BUCK1", "residual voltage on shutdown",
194 /* Operations permitted on BUCK1/2/3 */
238 TPS65219_REGULATOR("BUCK1", "buck1", TPS65219_BUCK_1,
|
| D | lp8788-buck.c | 82 BUCK1, enumerator
152 case BUCK1: in lp8788_set_dvs()
169 case BUCK1: in lp8788_get_buck_dvs_ctrl_mode()
211 case BUCK1: in lp8788_select_buck_vout_addr()
369 .name = "buck1",
370 .id = BUCK1,
432 case BUCK1: in lp8788_dvs_gpio_request()
474 if ((id == BUCK1 && !pdata->buck1_dvs) || in lp8788_init_dvs()
|
| D | tps65086-regulator.c | 17 enum tps65086_regulators { BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6, LDOA1, enumerator
118 TPS65086_REGULATOR("BUCK1", "buck1", BUCK1, 0x80, TPS65086_BUCK1CTRL,
166 case BUCK1: in tps65086_of_parse_cb()
|
| D | max8998.c | 258 "BUCK1, selector:%d, buck1_vol1:%d, buck1_vol2:%d\n" in max8998_set_voltage_buck_sel()
529 MAX8998_LINEAR_REG(BUCK1, &max8998_buck_ops, 750000, 25000, 1525000),
548 gpio = of_get_named_gpio(pmic_np, "max8998,pmic-buck1-dvs-gpios", 0); in max8998_pmic_dt_parse_dvs_gpio()
550 dev_err(iodev->dev, "invalid buck1 gpio[0]: %d\n", gpio); in max8998_pmic_dt_parse_dvs_gpio()
555 gpio = of_get_named_gpio(pmic_np, "max8998,pmic-buck1-dvs-gpios", 1); in max8998_pmic_dt_parse_dvs_gpio()
557 dev_err(iodev->dev, "invalid buck1 gpio[1]: %d\n", gpio); in max8998_pmic_dt_parse_dvs_gpio()
625 "max8998,pmic-buck1-default-dvs-idx", in max8998_pmic_dt_parse_pdata()
641 "max8998,pmic-buck1-dvs-voltage", in max8998_pmic_dt_parse_pdata()
645 dev_err(iodev->dev, "buck1 voltages not specified\n"); in max8998_pmic_dt_parse_pdata()
728 /* Set predefined values for BUCK1 registers */ in max8998_pmic_probe()
|
