| /Linux-v6.6/drivers/regulator/ |
| D | twl-regulator.c | 39 /* voltage in mV = table[VSEL]; table_len must be a power-of-two */
301 UNSUP(1000), UNSUP(1000), UNSUP(1200), 1300,
307 1700, 1700, 1900, 1300,
317 700, 1000, 1200, UNSUP(1300),
326 UNSUP(1000), UNSUP(1000), UNSUP(1200), UNSUP(1300),
332 1000, 1200, 1300, 1800,
336 700, 1000, 1200, 1300,
342 UNSUP(1000), UNSUP(1200), UNSUP(1300), 1800,
346 1200, 1300, 1800, 1800,
355 /* 600mV to 1450mV in 12.5 mV steps */
[all …]
|
| /Linux-v6.6/Documentation/devicetree/bindings/regulator/ |
| D | richtek,rt5739.yaml | 14 programmable output voltage from 300mV to 1300mV with wide input voltage
|
| /Linux-v6.6/drivers/iio/adc/ |
| D | ab8500-gpadc.c | 165 #define AB8500_ADC_CH_IBAT_MIN_V (-60) /* mV range measured by ADC for ibat */
167 #define AB8500_GPADC_IBAT_VDROP_L (-56) /* mV */
753 * vmain_high: Vin = 19500mV / ADC ideal code = 997 in ab8500_gpadc_read_calibration_data()
754 * vmain_low: Vin = 315mV / ADC ideal code = 16 in ab8500_gpadc_read_calibration_data()
755 * btemp_high: Vin = 1300mV / ADC ideal code = 985 in ab8500_gpadc_read_calibration_data()
756 * btemp_low: Vin = 21mV / ADC ideal code = 16 in ab8500_gpadc_read_calibration_data()
757 * vbat_high: Vin = 4700mV / ADC ideal code = 982 in ab8500_gpadc_read_calibration_data()
758 * vbat_low: Vin = 2380mV / ADC ideal code = 33 in ab8500_gpadc_read_calibration_data()
813 * Result obtained is in mV (at a scale factor), in ab8500_gpadc_read_calibration_data()
864 AB8500_GPADC_CALIB_SCALE * (1300 - 21) / (btemp_high - btemp_low); in ab8500_gpadc_read_calibration_data()
[all …]
|
| /Linux-v6.6/drivers/power/supply/ |
| D | adp5061.c | 82 #define ADP5061_ICHG_MAX 1300 // mA
120 700, 750, 800, 850, 900, 950, 1000, 1050, 1100, 1200, 1300,
212 /* Convert from uV to mV */ in adp5061_set_min_voltage()
280 /* Convert from uV to mV */ in adp5061_set_max_voltage()
301 /* Convert from uV to mV */ in adp5061_set_const_chg_vmax()
407 /* Convert from uV to mV */ in adp5061_set_vweak_th()
|
| /Linux-v6.6/drivers/cpufreq/ |
| D | speedstep-centrino.c | 83 frequency/voltage operating point; frequency in MHz, volts in mV.
85 #define OP(mhz, mv) \ argument
88 .driver_data = (((mhz)/100) << 8) | ((mv - 700) / 16) \
148 OP(1300, 1388),
216 BANIAS(1300),
|
| D | longhaul.h | 313 unsigned short mV; member
321 {1450, 16}, {1400, 14}, {1350, 12}, {1300, 10},
338 {1350, 23}, {1300, 22}, {1250, 21}, {1200, 20},
|
| /Linux-v6.6/drivers/mfd/ |
| D | menelaus.c | 449 static int menelaus_set_voltage(const struct menelaus_vtg *vtg, int mV, in menelaus_set_voltage() argument
464 "to %d mV (reg 0x%02x, val 0x%02x)\n", in menelaus_set_voltage()
465 vtg->name, mV, vtg->vtg_reg, val); in menelaus_set_voltage()
513 { 1300, 12 },
536 dev_dbg(&c->dev, "Setting VCORE FLOOR to %d mV and ROOF to %d mV\n", in menelaus_set_vcore_hw()
574 int menelaus_set_vmem(unsigned int mV) in menelaus_set_vmem() argument
578 if (mV == 0) in menelaus_set_vmem()
581 val = menelaus_get_vtg_value(mV, vmem_values, ARRAY_SIZE(vmem_values)); in menelaus_set_vmem()
584 return menelaus_set_voltage(&vmem_vtg, mV, val, 0x02); in menelaus_set_vmem()
603 int menelaus_set_vio(unsigned int mV) in menelaus_set_vio() argument
[all …]
|
| /Linux-v6.6/Documentation/admin-guide/media/ |
| D | gspca-cardlist.rst | 77 sunplus 0461:0821 Fujifilm MV-1
136 sunplus 04a5:3003 Benq DC 1300
419 pac207 145f:013a Trust WB-1300N
|
