Home
last modified time | relevance | path

Searched +full:064 +full:a (Results 1 – 4 of 4) sorted by relevance

/Linux-v6.6/Documentation/devicetree/bindings/mtd/
Djedec,spi-nor.yaml22 n25q(32b|064|128a11|128a13|256a|512a|164k)))|\
23 atmel,at25df(321a|641|081a)|\
25 (mxicy|macronix),mx25l(4005a|1606e|6405d|8005|12805d|25635e)|\
27 (spansion,)?s25fl(128s|256s1|512s|008k|064k|164k)|\
47 identified with the READ ID opcode (0x9F) do not deserve a specific
67 addressing) which need to be managed carefully by a system. Because these
68 sorts of flash don't have a standardized software reset command, and
72 be used on such systems, to denote the absence of a reliable reset
88 can be a valid use case.
92 A GPIO line connected to the RESET (active low) signal of the device.
/Linux-v6.6/sound/pci/pcxhr/
Dpcxhr_mix22.c167 0x22, /* [064] -17.5 dB: AKM[034] = -17.501 dB (diff=0.00123 dB) */
178 0x40, /* [075] -12.0 dB: AKM[064] = -12.007 dB (diff=0.00720 dB) */
309 /* TODO : there is a very similar fct in pcxhr.c */
/Linux-v6.6/sound/ppc/
Dsnd_ps3_reg.h65 DMA channel triggered the interrupt. The interrupt status for a channel
66 can be cleared by writing a '1' to the corresponding bit. A new interrupt
126 |0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0|A|A|A|0 0 0 0 0 0 0|S|S|A|A|A|A| AX_MCTRL
261 |0 0 0 0 0 0 0 0|S|S|0 0|A|A|A|A|0 0 0 0|S|S|0 0|S|S|0 0|A|A|A|A| AX_IE
309 Writing 1b to a field containing 1b clears field and de-asserts interrupt.
310 Writing 0b to a field has no effect.
318 |0 0 0 0 0 0 0 0|S|S|0 0|A|A|A|A|0 0 0 0|S|S|0 0|S|S|0 0|A|A|A|A| AX_IS
400 |A|A|A|A|0 0 0|A| ASOSR |0 0 0 0|A|A|A|A|A|A|0|1|0 0 0 0 0 0 0 0| AO_3WMCTRL
531 |0 0 0 0 0 0 0 0 0 0 0 0 0 0 0|A|0 0 0 0|A|0|ASO|0 0 0|0|0|0|0|0| AO_3WCTRL
551 or 24 bit resolution mode) is put in a 32 bit field.
[all …]
/Linux-v6.6/sound/pci/vx222/
Dvx222_ops.c81 * vx2_inb - read a byte from the register
91 * vx2_outb - write a byte on the register
105 * vx2_inl - read a 32bit word from the register
115 * vx2_outl - write a 32bit word on the register
451 * the ACQUIT signal up for a while ( a bus cycle ) in vx2_test_and_ack()
457 * the ACQUIT signal up for a while ( a bus cycle ) */ in vx2_test_and_ack()
578 0x2d, // [064] = -32.000 dB -> AKM(0x2d) = -31.945 dB error(+0.055 dB)
675 …/* `data' is a value between 0x0 and VX2_AKM_LEVEL_MAX = 0x093, in the case of the AKM codecs, we … in vx2_write_akm()
676 a look up table, as there is no linear matching between the driver codec values in vx2_write_akm()