1 /*
2 * Product specific probe and attach routines for:
3 * 3940, 2940, aic7895, aic7890, aic7880,
4 * aic7870, aic7860 and aic7850 SCSI controllers
5 *
6 * Copyright (c) 1994-2001 Justin T. Gibbs.
7 * Copyright (c) 2000-2001 Adaptec Inc.
8 * All rights reserved.
9 *
10 * Redistribution and use in source and binary forms, with or without
11 * modification, are permitted provided that the following conditions
12 * are met:
13 * 1. Redistributions of source code must retain the above copyright
14 * notice, this list of conditions, and the following disclaimer,
15 * without modification.
16 * 2. Redistributions in binary form must reproduce at minimum a disclaimer
17 * substantially similar to the "NO WARRANTY" disclaimer below
18 * ("Disclaimer") and any redistribution must be conditioned upon
19 * including a substantially similar Disclaimer requirement for further
20 * binary redistribution.
21 * 3. Neither the names of the above-listed copyright holders nor the names
22 * of any contributors may be used to endorse or promote products derived
23 * from this software without specific prior written permission.
24 *
25 * Alternatively, this software may be distributed under the terms of the
26 * GNU General Public License ("GPL") version 2 as published by the Free
27 * Software Foundation.
28 *
29 * NO WARRANTY
30 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
31 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
32 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR
33 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
34 * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
35 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
36 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
37 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
38 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
39 * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
40 * POSSIBILITY OF SUCH DAMAGES.
41 *
42 * $Id: //depot/aic7xxx/aic7xxx/aic7xxx_pci.c#79 $
43 */
44
45 #include "aic7xxx_osm.h"
46 #include "aic7xxx_inline.h"
47 #include "aic7xxx_93cx6.h"
48 #include "aic7xxx_pci.h"
49
50 static inline uint64_t
ahc_compose_id(u_int device,u_int vendor,u_int subdevice,u_int subvendor)51 ahc_compose_id(u_int device, u_int vendor, u_int subdevice, u_int subvendor)
52 {
53 uint64_t id;
54
55 id = subvendor
56 | (subdevice << 16)
57 | ((uint64_t)vendor << 32)
58 | ((uint64_t)device << 48);
59
60 return (id);
61 }
62
63 #define AHC_PCI_IOADDR PCIR_MAPS /* I/O Address */
64 #define AHC_PCI_MEMADDR (PCIR_MAPS + 4) /* Mem I/O Address */
65
66 #define DEVID_9005_TYPE(id) ((id) & 0xF)
67 #define DEVID_9005_TYPE_HBA 0x0 /* Standard Card */
68 #define DEVID_9005_TYPE_AAA 0x3 /* RAID Card */
69 #define DEVID_9005_TYPE_SISL 0x5 /* Container ROMB */
70 #define DEVID_9005_TYPE_MB 0xF /* On Motherboard */
71
72 #define DEVID_9005_MAXRATE(id) (((id) & 0x30) >> 4)
73 #define DEVID_9005_MAXRATE_U160 0x0
74 #define DEVID_9005_MAXRATE_ULTRA2 0x1
75 #define DEVID_9005_MAXRATE_ULTRA 0x2
76 #define DEVID_9005_MAXRATE_FAST 0x3
77
78 #define DEVID_9005_MFUNC(id) (((id) & 0x40) >> 6)
79
80 #define DEVID_9005_CLASS(id) (((id) & 0xFF00) >> 8)
81 #define DEVID_9005_CLASS_SPI 0x0 /* Parallel SCSI */
82
83 #define SUBID_9005_TYPE(id) ((id) & 0xF)
84 #define SUBID_9005_TYPE_MB 0xF /* On Motherboard */
85 #define SUBID_9005_TYPE_CARD 0x0 /* Standard Card */
86 #define SUBID_9005_TYPE_LCCARD 0x1 /* Low Cost Card */
87 #define SUBID_9005_TYPE_RAID 0x3 /* Combined with Raid */
88
89 #define SUBID_9005_TYPE_KNOWN(id) \
90 ((((id) & 0xF) == SUBID_9005_TYPE_MB) \
91 || (((id) & 0xF) == SUBID_9005_TYPE_CARD) \
92 || (((id) & 0xF) == SUBID_9005_TYPE_LCCARD) \
93 || (((id) & 0xF) == SUBID_9005_TYPE_RAID))
94
95 #define SUBID_9005_MAXRATE(id) (((id) & 0x30) >> 4)
96 #define SUBID_9005_MAXRATE_ULTRA2 0x0
97 #define SUBID_9005_MAXRATE_ULTRA 0x1
98 #define SUBID_9005_MAXRATE_U160 0x2
99 #define SUBID_9005_MAXRATE_RESERVED 0x3
100
101 #define SUBID_9005_SEEPTYPE(id) \
102 ((SUBID_9005_TYPE(id) == SUBID_9005_TYPE_MB) \
103 ? ((id) & 0xC0) >> 6 \
104 : ((id) & 0x300) >> 8)
105 #define SUBID_9005_SEEPTYPE_NONE 0x0
106 #define SUBID_9005_SEEPTYPE_1K 0x1
107 #define SUBID_9005_SEEPTYPE_2K_4K 0x2
108 #define SUBID_9005_SEEPTYPE_RESERVED 0x3
109 #define SUBID_9005_AUTOTERM(id) \
110 ((SUBID_9005_TYPE(id) == SUBID_9005_TYPE_MB) \
111 ? (((id) & 0x400) >> 10) == 0 \
112 : (((id) & 0x40) >> 6) == 0)
113
114 #define SUBID_9005_NUMCHAN(id) \
115 ((SUBID_9005_TYPE(id) == SUBID_9005_TYPE_MB) \
116 ? ((id) & 0x300) >> 8 \
117 : ((id) & 0xC00) >> 10)
118
119 #define SUBID_9005_LEGACYCONN(id) \
120 ((SUBID_9005_TYPE(id) == SUBID_9005_TYPE_MB) \
121 ? 0 \
122 : ((id) & 0x80) >> 7)
123
124 #define SUBID_9005_MFUNCENB(id) \
125 ((SUBID_9005_TYPE(id) == SUBID_9005_TYPE_MB) \
126 ? ((id) & 0x800) >> 11 \
127 : ((id) & 0x1000) >> 12)
128 /*
129 * Informational only. Should use chip register to be
130 * certain, but may be use in identification strings.
131 */
132 #define SUBID_9005_CARD_SCSIWIDTH_MASK 0x2000
133 #define SUBID_9005_CARD_PCIWIDTH_MASK 0x4000
134 #define SUBID_9005_CARD_SEDIFF_MASK 0x8000
135
136 static ahc_device_setup_t ahc_aic785X_setup;
137 static ahc_device_setup_t ahc_aic7860_setup;
138 static ahc_device_setup_t ahc_apa1480_setup;
139 static ahc_device_setup_t ahc_aic7870_setup;
140 static ahc_device_setup_t ahc_aic7870h_setup;
141 static ahc_device_setup_t ahc_aha394X_setup;
142 static ahc_device_setup_t ahc_aha394Xh_setup;
143 static ahc_device_setup_t ahc_aha494X_setup;
144 static ahc_device_setup_t ahc_aha494Xh_setup;
145 static ahc_device_setup_t ahc_aha398X_setup;
146 static ahc_device_setup_t ahc_aic7880_setup;
147 static ahc_device_setup_t ahc_aic7880h_setup;
148 static ahc_device_setup_t ahc_aha2940Pro_setup;
149 static ahc_device_setup_t ahc_aha394XU_setup;
150 static ahc_device_setup_t ahc_aha394XUh_setup;
151 static ahc_device_setup_t ahc_aha398XU_setup;
152 static ahc_device_setup_t ahc_aic7890_setup;
153 static ahc_device_setup_t ahc_aic7892_setup;
154 static ahc_device_setup_t ahc_aic7895_setup;
155 static ahc_device_setup_t ahc_aic7895h_setup;
156 static ahc_device_setup_t ahc_aic7896_setup;
157 static ahc_device_setup_t ahc_aic7899_setup;
158 static ahc_device_setup_t ahc_aha29160C_setup;
159 static ahc_device_setup_t ahc_raid_setup;
160 static ahc_device_setup_t ahc_aha394XX_setup;
161 static ahc_device_setup_t ahc_aha494XX_setup;
162 static ahc_device_setup_t ahc_aha398XX_setup;
163
164 static const struct ahc_pci_identity ahc_pci_ident_table[] = {
165 /* aic7850 based controllers */
166 {
167 ID_AHA_2902_04_10_15_20C_30C,
168 ID_ALL_MASK,
169 "Adaptec 2902/04/10/15/20C/30C SCSI adapter",
170 ahc_aic785X_setup
171 },
172 /* aic7860 based controllers */
173 {
174 ID_AHA_2930CU,
175 ID_ALL_MASK,
176 "Adaptec 2930CU SCSI adapter",
177 ahc_aic7860_setup
178 },
179 {
180 ID_AHA_1480A & ID_DEV_VENDOR_MASK,
181 ID_DEV_VENDOR_MASK,
182 "Adaptec 1480A Ultra SCSI adapter",
183 ahc_apa1480_setup
184 },
185 {
186 ID_AHA_2940AU_0 & ID_DEV_VENDOR_MASK,
187 ID_DEV_VENDOR_MASK,
188 "Adaptec 2940A Ultra SCSI adapter",
189 ahc_aic7860_setup
190 },
191 {
192 ID_AHA_2940AU_CN & ID_DEV_VENDOR_MASK,
193 ID_DEV_VENDOR_MASK,
194 "Adaptec 2940A/CN Ultra SCSI adapter",
195 ahc_aic7860_setup
196 },
197 {
198 ID_AHA_2930C_VAR & ID_DEV_VENDOR_MASK,
199 ID_DEV_VENDOR_MASK,
200 "Adaptec 2930C Ultra SCSI adapter (VAR)",
201 ahc_aic7860_setup
202 },
203 /* aic7870 based controllers */
204 {
205 ID_AHA_2940,
206 ID_ALL_MASK,
207 "Adaptec 2940 SCSI adapter",
208 ahc_aic7870_setup
209 },
210 {
211 ID_AHA_3940,
212 ID_ALL_MASK,
213 "Adaptec 3940 SCSI adapter",
214 ahc_aha394X_setup
215 },
216 {
217 ID_AHA_398X,
218 ID_ALL_MASK,
219 "Adaptec 398X SCSI RAID adapter",
220 ahc_aha398X_setup
221 },
222 {
223 ID_AHA_2944,
224 ID_ALL_MASK,
225 "Adaptec 2944 SCSI adapter",
226 ahc_aic7870h_setup
227 },
228 {
229 ID_AHA_3944,
230 ID_ALL_MASK,
231 "Adaptec 3944 SCSI adapter",
232 ahc_aha394Xh_setup
233 },
234 {
235 ID_AHA_4944,
236 ID_ALL_MASK,
237 "Adaptec 4944 SCSI adapter",
238 ahc_aha494Xh_setup
239 },
240 /* aic7880 based controllers */
241 {
242 ID_AHA_2940U & ID_DEV_VENDOR_MASK,
243 ID_DEV_VENDOR_MASK,
244 "Adaptec 2940 Ultra SCSI adapter",
245 ahc_aic7880_setup
246 },
247 {
248 ID_AHA_3940U & ID_DEV_VENDOR_MASK,
249 ID_DEV_VENDOR_MASK,
250 "Adaptec 3940 Ultra SCSI adapter",
251 ahc_aha394XU_setup
252 },
253 {
254 ID_AHA_2944U & ID_DEV_VENDOR_MASK,
255 ID_DEV_VENDOR_MASK,
256 "Adaptec 2944 Ultra SCSI adapter",
257 ahc_aic7880h_setup
258 },
259 {
260 ID_AHA_3944U & ID_DEV_VENDOR_MASK,
261 ID_DEV_VENDOR_MASK,
262 "Adaptec 3944 Ultra SCSI adapter",
263 ahc_aha394XUh_setup
264 },
265 {
266 ID_AHA_398XU & ID_DEV_VENDOR_MASK,
267 ID_DEV_VENDOR_MASK,
268 "Adaptec 398X Ultra SCSI RAID adapter",
269 ahc_aha398XU_setup
270 },
271 {
272 /*
273 * XXX Don't know the slot numbers
274 * so we can't identify channels
275 */
276 ID_AHA_4944U & ID_DEV_VENDOR_MASK,
277 ID_DEV_VENDOR_MASK,
278 "Adaptec 4944 Ultra SCSI adapter",
279 ahc_aic7880h_setup
280 },
281 {
282 ID_AHA_2930U & ID_DEV_VENDOR_MASK,
283 ID_DEV_VENDOR_MASK,
284 "Adaptec 2930 Ultra SCSI adapter",
285 ahc_aic7880_setup
286 },
287 {
288 ID_AHA_2940U_PRO & ID_DEV_VENDOR_MASK,
289 ID_DEV_VENDOR_MASK,
290 "Adaptec 2940 Pro Ultra SCSI adapter",
291 ahc_aha2940Pro_setup
292 },
293 {
294 ID_AHA_2940U_CN & ID_DEV_VENDOR_MASK,
295 ID_DEV_VENDOR_MASK,
296 "Adaptec 2940/CN Ultra SCSI adapter",
297 ahc_aic7880_setup
298 },
299 /* Ignore all SISL (AAC on MB) based controllers. */
300 {
301 ID_9005_SISL_ID,
302 ID_9005_SISL_MASK,
303 NULL,
304 NULL
305 },
306 /* aic7890 based controllers */
307 {
308 ID_AHA_2930U2,
309 ID_ALL_MASK,
310 "Adaptec 2930 Ultra2 SCSI adapter",
311 ahc_aic7890_setup
312 },
313 {
314 ID_AHA_2940U2B,
315 ID_ALL_MASK,
316 "Adaptec 2940B Ultra2 SCSI adapter",
317 ahc_aic7890_setup
318 },
319 {
320 ID_AHA_2940U2_OEM,
321 ID_ALL_MASK,
322 "Adaptec 2940 Ultra2 SCSI adapter (OEM)",
323 ahc_aic7890_setup
324 },
325 {
326 ID_AHA_2940U2,
327 ID_ALL_MASK,
328 "Adaptec 2940 Ultra2 SCSI adapter",
329 ahc_aic7890_setup
330 },
331 {
332 ID_AHA_2950U2B,
333 ID_ALL_MASK,
334 "Adaptec 2950 Ultra2 SCSI adapter",
335 ahc_aic7890_setup
336 },
337 {
338 ID_AIC7890_ARO,
339 ID_ALL_MASK,
340 "Adaptec aic7890/91 Ultra2 SCSI adapter (ARO)",
341 ahc_aic7890_setup
342 },
343 {
344 ID_AAA_131U2,
345 ID_ALL_MASK,
346 "Adaptec AAA-131 Ultra2 RAID adapter",
347 ahc_aic7890_setup
348 },
349 /* aic7892 based controllers */
350 {
351 ID_AHA_29160,
352 ID_ALL_MASK,
353 "Adaptec 29160 Ultra160 SCSI adapter",
354 ahc_aic7892_setup
355 },
356 {
357 ID_AHA_29160_CPQ,
358 ID_ALL_MASK,
359 "Adaptec (Compaq OEM) 29160 Ultra160 SCSI adapter",
360 ahc_aic7892_setup
361 },
362 {
363 ID_AHA_29160N,
364 ID_ALL_MASK,
365 "Adaptec 29160N Ultra160 SCSI adapter",
366 ahc_aic7892_setup
367 },
368 {
369 ID_AHA_29160C,
370 ID_ALL_MASK,
371 "Adaptec 29160C Ultra160 SCSI adapter",
372 ahc_aha29160C_setup
373 },
374 {
375 ID_AHA_29160B,
376 ID_ALL_MASK,
377 "Adaptec 29160B Ultra160 SCSI adapter",
378 ahc_aic7892_setup
379 },
380 {
381 ID_AHA_19160B,
382 ID_ALL_MASK,
383 "Adaptec 19160B Ultra160 SCSI adapter",
384 ahc_aic7892_setup
385 },
386 {
387 ID_AIC7892_ARO,
388 ID_ALL_MASK,
389 "Adaptec aic7892 Ultra160 SCSI adapter (ARO)",
390 ahc_aic7892_setup
391 },
392 {
393 ID_AHA_2915_30LP,
394 ID_ALL_MASK,
395 "Adaptec 2915/30LP Ultra160 SCSI adapter",
396 ahc_aic7892_setup
397 },
398 /* aic7895 based controllers */
399 {
400 ID_AHA_2940U_DUAL,
401 ID_ALL_MASK,
402 "Adaptec 2940/DUAL Ultra SCSI adapter",
403 ahc_aic7895_setup
404 },
405 {
406 ID_AHA_3940AU,
407 ID_ALL_MASK,
408 "Adaptec 3940A Ultra SCSI adapter",
409 ahc_aic7895_setup
410 },
411 {
412 ID_AHA_3944AU,
413 ID_ALL_MASK,
414 "Adaptec 3944A Ultra SCSI adapter",
415 ahc_aic7895h_setup
416 },
417 {
418 ID_AIC7895_ARO,
419 ID_AIC7895_ARO_MASK,
420 "Adaptec aic7895 Ultra SCSI adapter (ARO)",
421 ahc_aic7895_setup
422 },
423 /* aic7896/97 based controllers */
424 {
425 ID_AHA_3950U2B_0,
426 ID_ALL_MASK,
427 "Adaptec 3950B Ultra2 SCSI adapter",
428 ahc_aic7896_setup
429 },
430 {
431 ID_AHA_3950U2B_1,
432 ID_ALL_MASK,
433 "Adaptec 3950B Ultra2 SCSI adapter",
434 ahc_aic7896_setup
435 },
436 {
437 ID_AHA_3950U2D_0,
438 ID_ALL_MASK,
439 "Adaptec 3950D Ultra2 SCSI adapter",
440 ahc_aic7896_setup
441 },
442 {
443 ID_AHA_3950U2D_1,
444 ID_ALL_MASK,
445 "Adaptec 3950D Ultra2 SCSI adapter",
446 ahc_aic7896_setup
447 },
448 {
449 ID_AIC7896_ARO,
450 ID_ALL_MASK,
451 "Adaptec aic7896/97 Ultra2 SCSI adapter (ARO)",
452 ahc_aic7896_setup
453 },
454 /* aic7899 based controllers */
455 {
456 ID_AHA_3960D,
457 ID_ALL_MASK,
458 "Adaptec 3960D Ultra160 SCSI adapter",
459 ahc_aic7899_setup
460 },
461 {
462 ID_AHA_3960D_CPQ,
463 ID_ALL_MASK,
464 "Adaptec (Compaq OEM) 3960D Ultra160 SCSI adapter",
465 ahc_aic7899_setup
466 },
467 {
468 ID_AIC7899_ARO,
469 ID_ALL_MASK,
470 "Adaptec aic7899 Ultra160 SCSI adapter (ARO)",
471 ahc_aic7899_setup
472 },
473 /* Generic chip probes for devices we don't know 'exactly' */
474 {
475 ID_AIC7850 & ID_DEV_VENDOR_MASK,
476 ID_DEV_VENDOR_MASK,
477 "Adaptec aic7850 SCSI adapter",
478 ahc_aic785X_setup
479 },
480 {
481 ID_AIC7855 & ID_DEV_VENDOR_MASK,
482 ID_DEV_VENDOR_MASK,
483 "Adaptec aic7855 SCSI adapter",
484 ahc_aic785X_setup
485 },
486 {
487 ID_AIC7859 & ID_DEV_VENDOR_MASK,
488 ID_DEV_VENDOR_MASK,
489 "Adaptec aic7859 SCSI adapter",
490 ahc_aic7860_setup
491 },
492 {
493 ID_AIC7860 & ID_DEV_VENDOR_MASK,
494 ID_DEV_VENDOR_MASK,
495 "Adaptec aic7860 Ultra SCSI adapter",
496 ahc_aic7860_setup
497 },
498 {
499 ID_AIC7870 & ID_DEV_VENDOR_MASK,
500 ID_DEV_VENDOR_MASK,
501 "Adaptec aic7870 SCSI adapter",
502 ahc_aic7870_setup
503 },
504 {
505 ID_AIC7880 & ID_DEV_VENDOR_MASK,
506 ID_DEV_VENDOR_MASK,
507 "Adaptec aic7880 Ultra SCSI adapter",
508 ahc_aic7880_setup
509 },
510 {
511 ID_AIC7890 & ID_9005_GENERIC_MASK,
512 ID_9005_GENERIC_MASK,
513 "Adaptec aic7890/91 Ultra2 SCSI adapter",
514 ahc_aic7890_setup
515 },
516 {
517 ID_AIC7892 & ID_9005_GENERIC_MASK,
518 ID_9005_GENERIC_MASK,
519 "Adaptec aic7892 Ultra160 SCSI adapter",
520 ahc_aic7892_setup
521 },
522 {
523 ID_AIC7895 & ID_DEV_VENDOR_MASK,
524 ID_DEV_VENDOR_MASK,
525 "Adaptec aic7895 Ultra SCSI adapter",
526 ahc_aic7895_setup
527 },
528 {
529 ID_AIC7896 & ID_9005_GENERIC_MASK,
530 ID_9005_GENERIC_MASK,
531 "Adaptec aic7896/97 Ultra2 SCSI adapter",
532 ahc_aic7896_setup
533 },
534 {
535 ID_AIC7899 & ID_9005_GENERIC_MASK,
536 ID_9005_GENERIC_MASK,
537 "Adaptec aic7899 Ultra160 SCSI adapter",
538 ahc_aic7899_setup
539 },
540 {
541 ID_AIC7810 & ID_DEV_VENDOR_MASK,
542 ID_DEV_VENDOR_MASK,
543 "Adaptec aic7810 RAID memory controller",
544 ahc_raid_setup
545 },
546 {
547 ID_AIC7815 & ID_DEV_VENDOR_MASK,
548 ID_DEV_VENDOR_MASK,
549 "Adaptec aic7815 RAID memory controller",
550 ahc_raid_setup
551 }
552 };
553
554 static const u_int ahc_num_pci_devs = ARRAY_SIZE(ahc_pci_ident_table);
555
556 #define AHC_394X_SLOT_CHANNEL_A 4
557 #define AHC_394X_SLOT_CHANNEL_B 5
558
559 #define AHC_398X_SLOT_CHANNEL_A 4
560 #define AHC_398X_SLOT_CHANNEL_B 8
561 #define AHC_398X_SLOT_CHANNEL_C 12
562
563 #define AHC_494X_SLOT_CHANNEL_A 4
564 #define AHC_494X_SLOT_CHANNEL_B 5
565 #define AHC_494X_SLOT_CHANNEL_C 6
566 #define AHC_494X_SLOT_CHANNEL_D 7
567
568 #define DEVCONFIG 0x40
569 #define PCIERRGENDIS 0x80000000ul
570 #define SCBSIZE32 0x00010000ul /* aic789X only */
571 #define REXTVALID 0x00001000ul /* ultra cards only */
572 #define MPORTMODE 0x00000400ul /* aic7870+ only */
573 #define RAMPSM 0x00000200ul /* aic7870+ only */
574 #define VOLSENSE 0x00000100ul
575 #define PCI64BIT 0x00000080ul /* 64Bit PCI bus (Ultra2 Only)*/
576 #define SCBRAMSEL 0x00000080ul
577 #define MRDCEN 0x00000040ul
578 #define EXTSCBTIME 0x00000020ul /* aic7870 only */
579 #define EXTSCBPEN 0x00000010ul /* aic7870 only */
580 #define BERREN 0x00000008ul
581 #define DACEN 0x00000004ul
582 #define STPWLEVEL 0x00000002ul
583 #define DIFACTNEGEN 0x00000001ul /* aic7870 only */
584
585 #define CSIZE_LATTIME 0x0c
586 #define CACHESIZE 0x0000003ful /* only 5 bits */
587 #define LATTIME 0x0000ff00ul
588
589 /* PCI STATUS definitions */
590 #define DPE 0x80
591 #define SSE 0x40
592 #define RMA 0x20
593 #define RTA 0x10
594 #define STA 0x08
595 #define DPR 0x01
596
597 static int ahc_9005_subdevinfo_valid(uint16_t device, uint16_t vendor,
598 uint16_t subdevice, uint16_t subvendor);
599 static int ahc_ext_scbram_present(struct ahc_softc *ahc);
600 static void ahc_scbram_config(struct ahc_softc *ahc, int enable,
601 int pcheck, int fast, int large);
602 static void ahc_probe_ext_scbram(struct ahc_softc *ahc);
603 static void check_extport(struct ahc_softc *ahc, u_int *sxfrctl1);
604 static void ahc_parse_pci_eeprom(struct ahc_softc *ahc,
605 struct seeprom_config *sc);
606 static void configure_termination(struct ahc_softc *ahc,
607 struct seeprom_descriptor *sd,
608 u_int adapter_control,
609 u_int *sxfrctl1);
610
611 static void ahc_new_term_detect(struct ahc_softc *ahc,
612 int *enableSEC_low,
613 int *enableSEC_high,
614 int *enablePRI_low,
615 int *enablePRI_high,
616 int *eeprom_present);
617 static void aic787X_cable_detect(struct ahc_softc *ahc, int *internal50_present,
618 int *internal68_present,
619 int *externalcable_present,
620 int *eeprom_present);
621 static void aic785X_cable_detect(struct ahc_softc *ahc, int *internal50_present,
622 int *externalcable_present,
623 int *eeprom_present);
624 static void write_brdctl(struct ahc_softc *ahc, uint8_t value);
625 static uint8_t read_brdctl(struct ahc_softc *ahc);
626 static void ahc_pci_intr(struct ahc_softc *ahc);
627 static int ahc_pci_chip_init(struct ahc_softc *ahc);
628
629 static int
ahc_9005_subdevinfo_valid(uint16_t device,uint16_t vendor,uint16_t subdevice,uint16_t subvendor)630 ahc_9005_subdevinfo_valid(uint16_t device, uint16_t vendor,
631 uint16_t subdevice, uint16_t subvendor)
632 {
633 int result;
634
635 /* Default to invalid. */
636 result = 0;
637 if (vendor == 0x9005
638 && subvendor == 0x9005
639 && subdevice != device
640 && SUBID_9005_TYPE_KNOWN(subdevice) != 0) {
641
642 switch (SUBID_9005_TYPE(subdevice)) {
643 case SUBID_9005_TYPE_MB:
644 break;
645 case SUBID_9005_TYPE_CARD:
646 case SUBID_9005_TYPE_LCCARD:
647 /*
648 * Currently only trust Adaptec cards to
649 * get the sub device info correct.
650 */
651 if (DEVID_9005_TYPE(device) == DEVID_9005_TYPE_HBA)
652 result = 1;
653 break;
654 case SUBID_9005_TYPE_RAID:
655 break;
656 default:
657 break;
658 }
659 }
660 return (result);
661 }
662
663 const struct ahc_pci_identity *
ahc_find_pci_device(ahc_dev_softc_t pci)664 ahc_find_pci_device(ahc_dev_softc_t pci)
665 {
666 uint64_t full_id;
667 uint16_t device;
668 uint16_t vendor;
669 uint16_t subdevice;
670 uint16_t subvendor;
671 const struct ahc_pci_identity *entry;
672 u_int i;
673
674 vendor = ahc_pci_read_config(pci, PCIR_DEVVENDOR, /*bytes*/2);
675 device = ahc_pci_read_config(pci, PCIR_DEVICE, /*bytes*/2);
676 subvendor = ahc_pci_read_config(pci, PCIR_SUBVEND_0, /*bytes*/2);
677 subdevice = ahc_pci_read_config(pci, PCIR_SUBDEV_0, /*bytes*/2);
678 full_id = ahc_compose_id(device, vendor, subdevice, subvendor);
679
680 /*
681 * If the second function is not hooked up, ignore it.
682 * Unfortunately, not all MB vendors implement the
683 * subdevice ID as per the Adaptec spec, so do our best
684 * to sanity check it prior to accepting the subdevice
685 * ID as valid.
686 */
687 if (ahc_get_pci_function(pci) > 0
688 && ahc_9005_subdevinfo_valid(device, vendor, subdevice, subvendor)
689 && SUBID_9005_MFUNCENB(subdevice) == 0)
690 return (NULL);
691
692 for (i = 0; i < ahc_num_pci_devs; i++) {
693 entry = &ahc_pci_ident_table[i];
694 if (entry->full_id == (full_id & entry->id_mask)) {
695 /* Honor exclusion entries. */
696 if (entry->name == NULL)
697 return (NULL);
698 return (entry);
699 }
700 }
701 return (NULL);
702 }
703
704 int
ahc_pci_config(struct ahc_softc * ahc,const struct ahc_pci_identity * entry)705 ahc_pci_config(struct ahc_softc *ahc, const struct ahc_pci_identity *entry)
706 {
707 u_int command;
708 u_int our_id;
709 u_int sxfrctl1;
710 u_int scsiseq;
711 u_int dscommand0;
712 uint32_t devconfig;
713 int error;
714 uint8_t sblkctl;
715
716 our_id = 0;
717 error = entry->setup(ahc);
718 if (error != 0)
719 return (error);
720 ahc->chip |= AHC_PCI;
721 ahc->description = entry->name;
722
723 pci_set_power_state(ahc->dev_softc, AHC_POWER_STATE_D0);
724
725 error = ahc_pci_map_registers(ahc);
726 if (error != 0)
727 return (error);
728
729 /*
730 * Before we continue probing the card, ensure that
731 * its interrupts are *disabled*. We don't want
732 * a misstep to hang the machine in an interrupt
733 * storm.
734 */
735 ahc_intr_enable(ahc, FALSE);
736
737 devconfig = ahc_pci_read_config(ahc->dev_softc, DEVCONFIG, /*bytes*/4);
738
739 /*
740 * If we need to support high memory, enable dual
741 * address cycles. This bit must be set to enable
742 * high address bit generation even if we are on a
743 * 64bit bus (PCI64BIT set in devconfig).
744 */
745 if ((ahc->flags & AHC_39BIT_ADDRESSING) != 0) {
746
747 if (bootverbose)
748 printk("%s: Enabling 39Bit Addressing\n",
749 ahc_name(ahc));
750 devconfig |= DACEN;
751 }
752
753 /* Ensure that pci error generation, a test feature, is disabled. */
754 devconfig |= PCIERRGENDIS;
755
756 ahc_pci_write_config(ahc->dev_softc, DEVCONFIG, devconfig, /*bytes*/4);
757
758 /* Ensure busmastering is enabled */
759 command = ahc_pci_read_config(ahc->dev_softc, PCIR_COMMAND, /*bytes*/2);
760 command |= PCIM_CMD_BUSMASTEREN;
761
762 ahc_pci_write_config(ahc->dev_softc, PCIR_COMMAND, command, /*bytes*/2);
763
764 /* On all PCI adapters, we allow SCB paging */
765 ahc->flags |= AHC_PAGESCBS;
766
767 error = ahc_softc_init(ahc);
768 if (error != 0)
769 return (error);
770
771 /*
772 * Disable PCI parity error checking. Users typically
773 * do this to work around broken PCI chipsets that get
774 * the parity timing wrong and thus generate lots of spurious
775 * errors. The chip only allows us to disable *all* parity
776 * error reporting when doing this, so CIO bus, scb ram, and
777 * scratch ram parity errors will be ignored too.
778 */
779 if ((ahc->flags & AHC_DISABLE_PCI_PERR) != 0)
780 ahc->seqctl |= FAILDIS;
781
782 ahc->bus_intr = ahc_pci_intr;
783 ahc->bus_chip_init = ahc_pci_chip_init;
784
785 /* Remember how the card was setup in case there is no SEEPROM */
786 if ((ahc_inb(ahc, HCNTRL) & POWRDN) == 0) {
787 ahc_pause(ahc);
788 if ((ahc->features & AHC_ULTRA2) != 0)
789 our_id = ahc_inb(ahc, SCSIID_ULTRA2) & OID;
790 else
791 our_id = ahc_inb(ahc, SCSIID) & OID;
792 sxfrctl1 = ahc_inb(ahc, SXFRCTL1) & STPWEN;
793 scsiseq = ahc_inb(ahc, SCSISEQ);
794 } else {
795 sxfrctl1 = STPWEN;
796 our_id = 7;
797 scsiseq = 0;
798 }
799
800 error = ahc_reset(ahc, /*reinit*/FALSE);
801 if (error != 0)
802 return (ENXIO);
803
804 if ((ahc->features & AHC_DT) != 0) {
805 u_int sfunct;
806
807 /* Perform ALT-Mode Setup */
808 sfunct = ahc_inb(ahc, SFUNCT) & ~ALT_MODE;
809 ahc_outb(ahc, SFUNCT, sfunct | ALT_MODE);
810 ahc_outb(ahc, OPTIONMODE,
811 OPTIONMODE_DEFAULTS|AUTOACKEN|BUSFREEREV|EXPPHASEDIS);
812 ahc_outb(ahc, SFUNCT, sfunct);
813
814 /* Normal mode setup */
815 ahc_outb(ahc, CRCCONTROL1, CRCVALCHKEN|CRCENDCHKEN|CRCREQCHKEN
816 |TARGCRCENDEN);
817 }
818
819 dscommand0 = ahc_inb(ahc, DSCOMMAND0);
820 dscommand0 |= MPARCKEN|CACHETHEN;
821 if ((ahc->features & AHC_ULTRA2) != 0) {
822
823 /*
824 * DPARCKEN doesn't work correctly on
825 * some MBs so don't use it.
826 */
827 dscommand0 &= ~DPARCKEN;
828 }
829
830 /*
831 * Handle chips that must have cache line
832 * streaming (dis/en)abled.
833 */
834 if ((ahc->bugs & AHC_CACHETHEN_DIS_BUG) != 0)
835 dscommand0 |= CACHETHEN;
836
837 if ((ahc->bugs & AHC_CACHETHEN_BUG) != 0)
838 dscommand0 &= ~CACHETHEN;
839
840 ahc_outb(ahc, DSCOMMAND0, dscommand0);
841
842 ahc->pci_cachesize =
843 ahc_pci_read_config(ahc->dev_softc, CSIZE_LATTIME,
844 /*bytes*/1) & CACHESIZE;
845 ahc->pci_cachesize *= 4;
846
847 if ((ahc->bugs & AHC_PCI_2_1_RETRY_BUG) != 0
848 && ahc->pci_cachesize == 4) {
849
850 ahc_pci_write_config(ahc->dev_softc, CSIZE_LATTIME,
851 0, /*bytes*/1);
852 ahc->pci_cachesize = 0;
853 }
854
855 /*
856 * We cannot perform ULTRA speeds without the presence
857 * of the external precision resistor.
858 */
859 if ((ahc->features & AHC_ULTRA) != 0) {
860 uint32_t devconfig;
861
862 devconfig = ahc_pci_read_config(ahc->dev_softc,
863 DEVCONFIG, /*bytes*/4);
864 if ((devconfig & REXTVALID) == 0)
865 ahc->features &= ~AHC_ULTRA;
866 }
867
868 /* See if we have a SEEPROM and perform auto-term */
869 check_extport(ahc, &sxfrctl1);
870
871 /*
872 * Take the LED out of diagnostic mode
873 */
874 sblkctl = ahc_inb(ahc, SBLKCTL);
875 ahc_outb(ahc, SBLKCTL, (sblkctl & ~(DIAGLEDEN|DIAGLEDON)));
876
877 if ((ahc->features & AHC_ULTRA2) != 0) {
878 ahc_outb(ahc, DFF_THRSH, RD_DFTHRSH_MAX|WR_DFTHRSH_MAX);
879 } else {
880 ahc_outb(ahc, DSPCISTATUS, DFTHRSH_100);
881 }
882
883 if (ahc->flags & AHC_USEDEFAULTS) {
884 /*
885 * PCI Adapter default setup
886 * Should only be used if the adapter does not have
887 * a SEEPROM.
888 */
889 /* See if someone else set us up already */
890 if ((ahc->flags & AHC_NO_BIOS_INIT) == 0
891 && scsiseq != 0) {
892 printk("%s: Using left over BIOS settings\n",
893 ahc_name(ahc));
894 ahc->flags &= ~AHC_USEDEFAULTS;
895 ahc->flags |= AHC_BIOS_ENABLED;
896 } else {
897 /*
898 * Assume only one connector and always turn
899 * on termination.
900 */
901 our_id = 0x07;
902 sxfrctl1 = STPWEN;
903 }
904 ahc_outb(ahc, SCSICONF, our_id|ENSPCHK|RESET_SCSI);
905
906 ahc->our_id = our_id;
907 }
908
909 /*
910 * Take a look to see if we have external SRAM.
911 * We currently do not attempt to use SRAM that is
912 * shared among multiple controllers.
913 */
914 ahc_probe_ext_scbram(ahc);
915
916 /*
917 * Record our termination setting for the
918 * generic initialization routine.
919 */
920 if ((sxfrctl1 & STPWEN) != 0)
921 ahc->flags |= AHC_TERM_ENB_A;
922
923 /*
924 * Save chip register configuration data for chip resets
925 * that occur during runtime and resume events.
926 */
927 ahc->bus_softc.pci_softc.devconfig =
928 ahc_pci_read_config(ahc->dev_softc, DEVCONFIG, /*bytes*/4);
929 ahc->bus_softc.pci_softc.command =
930 ahc_pci_read_config(ahc->dev_softc, PCIR_COMMAND, /*bytes*/1);
931 ahc->bus_softc.pci_softc.csize_lattime =
932 ahc_pci_read_config(ahc->dev_softc, CSIZE_LATTIME, /*bytes*/1);
933 ahc->bus_softc.pci_softc.dscommand0 = ahc_inb(ahc, DSCOMMAND0);
934 ahc->bus_softc.pci_softc.dspcistatus = ahc_inb(ahc, DSPCISTATUS);
935 if ((ahc->features & AHC_DT) != 0) {
936 u_int sfunct;
937
938 sfunct = ahc_inb(ahc, SFUNCT) & ~ALT_MODE;
939 ahc_outb(ahc, SFUNCT, sfunct | ALT_MODE);
940 ahc->bus_softc.pci_softc.optionmode = ahc_inb(ahc, OPTIONMODE);
941 ahc->bus_softc.pci_softc.targcrccnt = ahc_inw(ahc, TARGCRCCNT);
942 ahc_outb(ahc, SFUNCT, sfunct);
943 ahc->bus_softc.pci_softc.crccontrol1 =
944 ahc_inb(ahc, CRCCONTROL1);
945 }
946 if ((ahc->features & AHC_MULTI_FUNC) != 0)
947 ahc->bus_softc.pci_softc.scbbaddr = ahc_inb(ahc, SCBBADDR);
948
949 if ((ahc->features & AHC_ULTRA2) != 0)
950 ahc->bus_softc.pci_softc.dff_thrsh = ahc_inb(ahc, DFF_THRSH);
951
952 /* Core initialization */
953 error = ahc_init(ahc);
954 if (error != 0)
955 return (error);
956 ahc->init_level++;
957
958 /*
959 * Allow interrupts now that we are completely setup.
960 */
961 return ahc_pci_map_int(ahc);
962 }
963
964 /*
965 * Test for the presence of external sram in an
966 * "unshared" configuration.
967 */
968 static int
ahc_ext_scbram_present(struct ahc_softc * ahc)969 ahc_ext_scbram_present(struct ahc_softc *ahc)
970 {
971 u_int chip;
972 int ramps;
973 int single_user;
974 uint32_t devconfig;
975
976 chip = ahc->chip & AHC_CHIPID_MASK;
977 devconfig = ahc_pci_read_config(ahc->dev_softc,
978 DEVCONFIG, /*bytes*/4);
979 single_user = (devconfig & MPORTMODE) != 0;
980
981 if ((ahc->features & AHC_ULTRA2) != 0)
982 ramps = (ahc_inb(ahc, DSCOMMAND0) & RAMPS) != 0;
983 else if (chip == AHC_AIC7895 || chip == AHC_AIC7895C)
984 /*
985 * External SCBRAM arbitration is flakey
986 * on these chips. Unfortunately this means
987 * we don't use the extra SCB ram space on the
988 * 3940AUW.
989 */
990 ramps = 0;
991 else if (chip >= AHC_AIC7870)
992 ramps = (devconfig & RAMPSM) != 0;
993 else
994 ramps = 0;
995
996 if (ramps && single_user)
997 return (1);
998 return (0);
999 }
1000
1001 /*
1002 * Enable external scbram.
1003 */
1004 static void
ahc_scbram_config(struct ahc_softc * ahc,int enable,int pcheck,int fast,int large)1005 ahc_scbram_config(struct ahc_softc *ahc, int enable, int pcheck,
1006 int fast, int large)
1007 {
1008 uint32_t devconfig;
1009
1010 if (ahc->features & AHC_MULTI_FUNC) {
1011 /*
1012 * Set the SCB Base addr (highest address bit)
1013 * depending on which channel we are.
1014 */
1015 ahc_outb(ahc, SCBBADDR, ahc_get_pci_function(ahc->dev_softc));
1016 }
1017
1018 ahc->flags &= ~AHC_LSCBS_ENABLED;
1019 if (large)
1020 ahc->flags |= AHC_LSCBS_ENABLED;
1021 devconfig = ahc_pci_read_config(ahc->dev_softc, DEVCONFIG, /*bytes*/4);
1022 if ((ahc->features & AHC_ULTRA2) != 0) {
1023 u_int dscommand0;
1024
1025 dscommand0 = ahc_inb(ahc, DSCOMMAND0);
1026 if (enable)
1027 dscommand0 &= ~INTSCBRAMSEL;
1028 else
1029 dscommand0 |= INTSCBRAMSEL;
1030 if (large)
1031 dscommand0 &= ~USCBSIZE32;
1032 else
1033 dscommand0 |= USCBSIZE32;
1034 ahc_outb(ahc, DSCOMMAND0, dscommand0);
1035 } else {
1036 if (fast)
1037 devconfig &= ~EXTSCBTIME;
1038 else
1039 devconfig |= EXTSCBTIME;
1040 if (enable)
1041 devconfig &= ~SCBRAMSEL;
1042 else
1043 devconfig |= SCBRAMSEL;
1044 if (large)
1045 devconfig &= ~SCBSIZE32;
1046 else
1047 devconfig |= SCBSIZE32;
1048 }
1049 if (pcheck)
1050 devconfig |= EXTSCBPEN;
1051 else
1052 devconfig &= ~EXTSCBPEN;
1053
1054 ahc_pci_write_config(ahc->dev_softc, DEVCONFIG, devconfig, /*bytes*/4);
1055 }
1056
1057 /*
1058 * Take a look to see if we have external SRAM.
1059 * We currently do not attempt to use SRAM that is
1060 * shared among multiple controllers.
1061 */
1062 static void
ahc_probe_ext_scbram(struct ahc_softc * ahc)1063 ahc_probe_ext_scbram(struct ahc_softc *ahc)
1064 {
1065 int num_scbs;
1066 int test_num_scbs;
1067 int enable;
1068 int pcheck;
1069 int fast;
1070 int large;
1071
1072 enable = FALSE;
1073 pcheck = FALSE;
1074 fast = FALSE;
1075 large = FALSE;
1076 num_scbs = 0;
1077
1078 if (ahc_ext_scbram_present(ahc) == 0)
1079 goto done;
1080
1081 /*
1082 * Probe for the best parameters to use.
1083 */
1084 ahc_scbram_config(ahc, /*enable*/TRUE, pcheck, fast, large);
1085 num_scbs = ahc_probe_scbs(ahc);
1086 if (num_scbs == 0) {
1087 /* The SRAM wasn't really present. */
1088 goto done;
1089 }
1090 enable = TRUE;
1091
1092 /*
1093 * Clear any outstanding parity error
1094 * and ensure that parity error reporting
1095 * is enabled.
1096 */
1097 ahc_outb(ahc, SEQCTL, 0);
1098 ahc_outb(ahc, CLRINT, CLRPARERR);
1099 ahc_outb(ahc, CLRINT, CLRBRKADRINT);
1100
1101 /* Now see if we can do parity */
1102 ahc_scbram_config(ahc, enable, /*pcheck*/TRUE, fast, large);
1103 num_scbs = ahc_probe_scbs(ahc);
1104 if ((ahc_inb(ahc, INTSTAT) & BRKADRINT) == 0
1105 || (ahc_inb(ahc, ERROR) & MPARERR) == 0)
1106 pcheck = TRUE;
1107
1108 /* Clear any resulting parity error */
1109 ahc_outb(ahc, CLRINT, CLRPARERR);
1110 ahc_outb(ahc, CLRINT, CLRBRKADRINT);
1111
1112 /* Now see if we can do fast timing */
1113 ahc_scbram_config(ahc, enable, pcheck, /*fast*/TRUE, large);
1114 test_num_scbs = ahc_probe_scbs(ahc);
1115 if (test_num_scbs == num_scbs
1116 && ((ahc_inb(ahc, INTSTAT) & BRKADRINT) == 0
1117 || (ahc_inb(ahc, ERROR) & MPARERR) == 0))
1118 fast = TRUE;
1119
1120 /*
1121 * See if we can use large SCBs and still maintain
1122 * the same overall count of SCBs.
1123 */
1124 if ((ahc->features & AHC_LARGE_SCBS) != 0) {
1125 ahc_scbram_config(ahc, enable, pcheck, fast, /*large*/TRUE);
1126 test_num_scbs = ahc_probe_scbs(ahc);
1127 if (test_num_scbs >= num_scbs) {
1128 large = TRUE;
1129 num_scbs = test_num_scbs;
1130 if (num_scbs >= 64) {
1131 /*
1132 * We have enough space to move the
1133 * "busy targets table" into SCB space
1134 * and make it qualify all the way to the
1135 * lun level.
1136 */
1137 ahc->flags |= AHC_SCB_BTT;
1138 }
1139 }
1140 }
1141 done:
1142 /*
1143 * Disable parity error reporting until we
1144 * can load instruction ram.
1145 */
1146 ahc_outb(ahc, SEQCTL, PERRORDIS|FAILDIS);
1147 /* Clear any latched parity error */
1148 ahc_outb(ahc, CLRINT, CLRPARERR);
1149 ahc_outb(ahc, CLRINT, CLRBRKADRINT);
1150 if (bootverbose && enable) {
1151 printk("%s: External SRAM, %s access%s, %dbytes/SCB\n",
1152 ahc_name(ahc), fast ? "fast" : "slow",
1153 pcheck ? ", parity checking enabled" : "",
1154 large ? 64 : 32);
1155 }
1156 ahc_scbram_config(ahc, enable, pcheck, fast, large);
1157 }
1158
1159 /*
1160 * Perform some simple tests that should catch situations where
1161 * our registers are invalidly mapped.
1162 */
1163 int
ahc_pci_test_register_access(struct ahc_softc * ahc)1164 ahc_pci_test_register_access(struct ahc_softc *ahc)
1165 {
1166 int error;
1167 u_int status1;
1168 uint32_t cmd;
1169 uint8_t hcntrl;
1170
1171 error = EIO;
1172
1173 /*
1174 * Enable PCI error interrupt status, but suppress NMIs
1175 * generated by SERR raised due to target aborts.
1176 */
1177 cmd = ahc_pci_read_config(ahc->dev_softc, PCIR_COMMAND, /*bytes*/2);
1178 ahc_pci_write_config(ahc->dev_softc, PCIR_COMMAND,
1179 cmd & ~PCIM_CMD_SERRESPEN, /*bytes*/2);
1180
1181 /*
1182 * First a simple test to see if any
1183 * registers can be read. Reading
1184 * HCNTRL has no side effects and has
1185 * at least one bit that is guaranteed to
1186 * be zero so it is a good register to
1187 * use for this test.
1188 */
1189 hcntrl = ahc_inb(ahc, HCNTRL);
1190
1191 if (hcntrl == 0xFF)
1192 goto fail;
1193
1194 if ((hcntrl & CHIPRST) != 0) {
1195 /*
1196 * The chip has not been initialized since
1197 * PCI/EISA/VLB bus reset. Don't trust
1198 * "left over BIOS data".
1199 */
1200 ahc->flags |= AHC_NO_BIOS_INIT;
1201 }
1202
1203 /*
1204 * Next create a situation where write combining
1205 * or read prefetching could be initiated by the
1206 * CPU or host bridge. Our device does not support
1207 * either, so look for data corruption and/or flagged
1208 * PCI errors. First pause without causing another
1209 * chip reset.
1210 */
1211 hcntrl &= ~CHIPRST;
1212 ahc_outb(ahc, HCNTRL, hcntrl|PAUSE);
1213 while (ahc_is_paused(ahc) == 0)
1214 ;
1215
1216 /* Clear any PCI errors that occurred before our driver attached. */
1217 status1 = ahc_pci_read_config(ahc->dev_softc,
1218 PCIR_STATUS + 1, /*bytes*/1);
1219 ahc_pci_write_config(ahc->dev_softc, PCIR_STATUS + 1,
1220 status1, /*bytes*/1);
1221 ahc_outb(ahc, CLRINT, CLRPARERR);
1222
1223 ahc_outb(ahc, SEQCTL, PERRORDIS);
1224 ahc_outb(ahc, SCBPTR, 0);
1225 ahc_outl(ahc, SCB_BASE, 0x5aa555aa);
1226 if (ahc_inl(ahc, SCB_BASE) != 0x5aa555aa)
1227 goto fail;
1228
1229 status1 = ahc_pci_read_config(ahc->dev_softc,
1230 PCIR_STATUS + 1, /*bytes*/1);
1231 if ((status1 & STA) != 0)
1232 goto fail;
1233
1234 error = 0;
1235
1236 fail:
1237 /* Silently clear any latched errors. */
1238 status1 = ahc_pci_read_config(ahc->dev_softc,
1239 PCIR_STATUS + 1, /*bytes*/1);
1240 ahc_pci_write_config(ahc->dev_softc, PCIR_STATUS + 1,
1241 status1, /*bytes*/1);
1242 ahc_outb(ahc, CLRINT, CLRPARERR);
1243 ahc_outb(ahc, SEQCTL, PERRORDIS|FAILDIS);
1244 ahc_pci_write_config(ahc->dev_softc, PCIR_COMMAND, cmd, /*bytes*/2);
1245 return (error);
1246 }
1247
1248 /*
1249 * Check the external port logic for a serial eeprom
1250 * and termination/cable detection contrls.
1251 */
1252 static void
check_extport(struct ahc_softc * ahc,u_int * sxfrctl1)1253 check_extport(struct ahc_softc *ahc, u_int *sxfrctl1)
1254 {
1255 struct seeprom_descriptor sd;
1256 struct seeprom_config *sc;
1257 int have_seeprom;
1258 int have_autoterm;
1259
1260 sd.sd_ahc = ahc;
1261 sd.sd_control_offset = SEECTL;
1262 sd.sd_status_offset = SEECTL;
1263 sd.sd_dataout_offset = SEECTL;
1264 sc = ahc->seep_config;
1265
1266 /*
1267 * For some multi-channel devices, the c46 is simply too
1268 * small to work. For the other controller types, we can
1269 * get our information from either SEEPROM type. Set the
1270 * type to start our probe with accordingly.
1271 */
1272 if (ahc->flags & AHC_LARGE_SEEPROM)
1273 sd.sd_chip = C56_66;
1274 else
1275 sd.sd_chip = C46;
1276
1277 sd.sd_MS = SEEMS;
1278 sd.sd_RDY = SEERDY;
1279 sd.sd_CS = SEECS;
1280 sd.sd_CK = SEECK;
1281 sd.sd_DO = SEEDO;
1282 sd.sd_DI = SEEDI;
1283
1284 have_seeprom = ahc_acquire_seeprom(ahc, &sd);
1285 if (have_seeprom) {
1286
1287 if (bootverbose)
1288 printk("%s: Reading SEEPROM...", ahc_name(ahc));
1289
1290 for (;;) {
1291 u_int start_addr;
1292
1293 start_addr = 32 * (ahc->channel - 'A');
1294
1295 have_seeprom = ahc_read_seeprom(&sd, (uint16_t *)sc,
1296 start_addr,
1297 sizeof(*sc)/2);
1298
1299 if (have_seeprom)
1300 have_seeprom = ahc_verify_cksum(sc);
1301
1302 if (have_seeprom != 0 || sd.sd_chip == C56_66) {
1303 if (bootverbose) {
1304 if (have_seeprom == 0)
1305 printk ("checksum error\n");
1306 else
1307 printk ("done.\n");
1308 }
1309 break;
1310 }
1311 sd.sd_chip = C56_66;
1312 }
1313 ahc_release_seeprom(&sd);
1314
1315 /* Remember the SEEPROM type for later */
1316 if (sd.sd_chip == C56_66)
1317 ahc->flags |= AHC_LARGE_SEEPROM;
1318 }
1319
1320 if (!have_seeprom) {
1321 /*
1322 * Pull scratch ram settings and treat them as
1323 * if they are the contents of an seeprom if
1324 * the 'ADPT' signature is found in SCB2.
1325 * We manually compose the data as 16bit values
1326 * to avoid endian issues.
1327 */
1328 ahc_outb(ahc, SCBPTR, 2);
1329 if (ahc_inb(ahc, SCB_BASE) == 'A'
1330 && ahc_inb(ahc, SCB_BASE + 1) == 'D'
1331 && ahc_inb(ahc, SCB_BASE + 2) == 'P'
1332 && ahc_inb(ahc, SCB_BASE + 3) == 'T') {
1333 uint16_t *sc_data;
1334 int i;
1335
1336 sc_data = (uint16_t *)sc;
1337 for (i = 0; i < 32; i++, sc_data++) {
1338 int j;
1339
1340 j = i * 2;
1341 *sc_data = ahc_inb(ahc, SRAM_BASE + j)
1342 | ahc_inb(ahc, SRAM_BASE + j + 1) << 8;
1343 }
1344 have_seeprom = ahc_verify_cksum(sc);
1345 if (have_seeprom)
1346 ahc->flags |= AHC_SCB_CONFIG_USED;
1347 }
1348 /*
1349 * Clear any SCB parity errors in case this data and
1350 * its associated parity was not initialized by the BIOS
1351 */
1352 ahc_outb(ahc, CLRINT, CLRPARERR);
1353 ahc_outb(ahc, CLRINT, CLRBRKADRINT);
1354 }
1355
1356 if (!have_seeprom) {
1357 if (bootverbose)
1358 printk("%s: No SEEPROM available.\n", ahc_name(ahc));
1359 ahc->flags |= AHC_USEDEFAULTS;
1360 kfree(ahc->seep_config);
1361 ahc->seep_config = NULL;
1362 sc = NULL;
1363 } else {
1364 ahc_parse_pci_eeprom(ahc, sc);
1365 }
1366
1367 /*
1368 * Cards that have the external logic necessary to talk to
1369 * a SEEPROM, are almost certain to have the remaining logic
1370 * necessary for auto-termination control. This assumption
1371 * hasn't failed yet...
1372 */
1373 have_autoterm = have_seeprom;
1374
1375 /*
1376 * Some low-cost chips have SEEPROM and auto-term control built
1377 * in, instead of using a GAL. They can tell us directly
1378 * if the termination logic is enabled.
1379 */
1380 if ((ahc->features & AHC_SPIOCAP) != 0) {
1381 if ((ahc_inb(ahc, SPIOCAP) & SSPIOCPS) == 0)
1382 have_autoterm = FALSE;
1383 }
1384
1385 if (have_autoterm) {
1386 ahc->flags |= AHC_HAS_TERM_LOGIC;
1387 ahc_acquire_seeprom(ahc, &sd);
1388 configure_termination(ahc, &sd, sc->adapter_control, sxfrctl1);
1389 ahc_release_seeprom(&sd);
1390 } else if (have_seeprom) {
1391 *sxfrctl1 &= ~STPWEN;
1392 if ((sc->adapter_control & CFSTERM) != 0)
1393 *sxfrctl1 |= STPWEN;
1394 if (bootverbose)
1395 printk("%s: Low byte termination %sabled\n",
1396 ahc_name(ahc),
1397 (*sxfrctl1 & STPWEN) ? "en" : "dis");
1398 }
1399 }
1400
1401 static void
ahc_parse_pci_eeprom(struct ahc_softc * ahc,struct seeprom_config * sc)1402 ahc_parse_pci_eeprom(struct ahc_softc *ahc, struct seeprom_config *sc)
1403 {
1404 /*
1405 * Put the data we've collected down into SRAM
1406 * where ahc_init will find it.
1407 */
1408 int i;
1409 int max_targ = sc->max_targets & CFMAXTARG;
1410 u_int scsi_conf;
1411 uint16_t discenable;
1412 uint16_t ultraenb;
1413
1414 discenable = 0;
1415 ultraenb = 0;
1416 if ((sc->adapter_control & CFULTRAEN) != 0) {
1417 /*
1418 * Determine if this adapter has a "newstyle"
1419 * SEEPROM format.
1420 */
1421 for (i = 0; i < max_targ; i++) {
1422 if ((sc->device_flags[i] & CFSYNCHISULTRA) != 0) {
1423 ahc->flags |= AHC_NEWEEPROM_FMT;
1424 break;
1425 }
1426 }
1427 }
1428
1429 for (i = 0; i < max_targ; i++) {
1430 u_int scsirate;
1431 uint16_t target_mask;
1432
1433 target_mask = 0x01 << i;
1434 if (sc->device_flags[i] & CFDISC)
1435 discenable |= target_mask;
1436 if ((ahc->flags & AHC_NEWEEPROM_FMT) != 0) {
1437 if ((sc->device_flags[i] & CFSYNCHISULTRA) != 0)
1438 ultraenb |= target_mask;
1439 } else if ((sc->adapter_control & CFULTRAEN) != 0) {
1440 ultraenb |= target_mask;
1441 }
1442 if ((sc->device_flags[i] & CFXFER) == 0x04
1443 && (ultraenb & target_mask) != 0) {
1444 /* Treat 10MHz as a non-ultra speed */
1445 sc->device_flags[i] &= ~CFXFER;
1446 ultraenb &= ~target_mask;
1447 }
1448 if ((ahc->features & AHC_ULTRA2) != 0) {
1449 u_int offset;
1450
1451 if (sc->device_flags[i] & CFSYNCH)
1452 offset = MAX_OFFSET_ULTRA2;
1453 else
1454 offset = 0;
1455 ahc_outb(ahc, TARG_OFFSET + i, offset);
1456
1457 /*
1458 * The ultra enable bits contain the
1459 * high bit of the ultra2 sync rate
1460 * field.
1461 */
1462 scsirate = (sc->device_flags[i] & CFXFER)
1463 | ((ultraenb & target_mask) ? 0x8 : 0x0);
1464 if (sc->device_flags[i] & CFWIDEB)
1465 scsirate |= WIDEXFER;
1466 } else {
1467 scsirate = (sc->device_flags[i] & CFXFER) << 4;
1468 if (sc->device_flags[i] & CFSYNCH)
1469 scsirate |= SOFS;
1470 if (sc->device_flags[i] & CFWIDEB)
1471 scsirate |= WIDEXFER;
1472 }
1473 ahc_outb(ahc, TARG_SCSIRATE + i, scsirate);
1474 }
1475 ahc->our_id = sc->brtime_id & CFSCSIID;
1476
1477 scsi_conf = (ahc->our_id & 0x7);
1478 if (sc->adapter_control & CFSPARITY)
1479 scsi_conf |= ENSPCHK;
1480 if (sc->adapter_control & CFRESETB)
1481 scsi_conf |= RESET_SCSI;
1482
1483 ahc->flags |= (sc->adapter_control & CFBOOTCHAN) >> CFBOOTCHANSHIFT;
1484
1485 if (sc->bios_control & CFEXTEND)
1486 ahc->flags |= AHC_EXTENDED_TRANS_A;
1487
1488 if (sc->bios_control & CFBIOSEN)
1489 ahc->flags |= AHC_BIOS_ENABLED;
1490 if (ahc->features & AHC_ULTRA
1491 && (ahc->flags & AHC_NEWEEPROM_FMT) == 0) {
1492 /* Should we enable Ultra mode? */
1493 if (!(sc->adapter_control & CFULTRAEN))
1494 /* Treat us as a non-ultra card */
1495 ultraenb = 0;
1496 }
1497
1498 if (sc->signature == CFSIGNATURE
1499 || sc->signature == CFSIGNATURE2) {
1500 uint32_t devconfig;
1501
1502 /* Honor the STPWLEVEL settings */
1503 devconfig = ahc_pci_read_config(ahc->dev_softc,
1504 DEVCONFIG, /*bytes*/4);
1505 devconfig &= ~STPWLEVEL;
1506 if ((sc->bios_control & CFSTPWLEVEL) != 0)
1507 devconfig |= STPWLEVEL;
1508 ahc_pci_write_config(ahc->dev_softc, DEVCONFIG,
1509 devconfig, /*bytes*/4);
1510 }
1511 /* Set SCSICONF info */
1512 ahc_outb(ahc, SCSICONF, scsi_conf);
1513 ahc_outb(ahc, DISC_DSB, ~(discenable & 0xff));
1514 ahc_outb(ahc, DISC_DSB + 1, ~((discenable >> 8) & 0xff));
1515 ahc_outb(ahc, ULTRA_ENB, ultraenb & 0xff);
1516 ahc_outb(ahc, ULTRA_ENB + 1, (ultraenb >> 8) & 0xff);
1517 }
1518
1519 static void
configure_termination(struct ahc_softc * ahc,struct seeprom_descriptor * sd,u_int adapter_control,u_int * sxfrctl1)1520 configure_termination(struct ahc_softc *ahc,
1521 struct seeprom_descriptor *sd,
1522 u_int adapter_control,
1523 u_int *sxfrctl1)
1524 {
1525 uint8_t brddat;
1526
1527 brddat = 0;
1528
1529 /*
1530 * Update the settings in sxfrctl1 to match the
1531 * termination settings
1532 */
1533 *sxfrctl1 = 0;
1534
1535 /*
1536 * SEECS must be on for the GALS to latch
1537 * the data properly. Be sure to leave MS
1538 * on or we will release the seeprom.
1539 */
1540 SEEPROM_OUTB(sd, sd->sd_MS | sd->sd_CS);
1541 if ((adapter_control & CFAUTOTERM) != 0
1542 || (ahc->features & AHC_NEW_TERMCTL) != 0) {
1543 int internal50_present;
1544 int internal68_present;
1545 int externalcable_present;
1546 int eeprom_present;
1547 int enableSEC_low;
1548 int enableSEC_high;
1549 int enablePRI_low;
1550 int enablePRI_high;
1551 int sum;
1552
1553 enableSEC_low = 0;
1554 enableSEC_high = 0;
1555 enablePRI_low = 0;
1556 enablePRI_high = 0;
1557 if ((ahc->features & AHC_NEW_TERMCTL) != 0) {
1558 ahc_new_term_detect(ahc, &enableSEC_low,
1559 &enableSEC_high,
1560 &enablePRI_low,
1561 &enablePRI_high,
1562 &eeprom_present);
1563 if ((adapter_control & CFSEAUTOTERM) == 0) {
1564 if (bootverbose)
1565 printk("%s: Manual SE Termination\n",
1566 ahc_name(ahc));
1567 enableSEC_low = (adapter_control & CFSELOWTERM);
1568 enableSEC_high =
1569 (adapter_control & CFSEHIGHTERM);
1570 }
1571 if ((adapter_control & CFAUTOTERM) == 0) {
1572 if (bootverbose)
1573 printk("%s: Manual LVD Termination\n",
1574 ahc_name(ahc));
1575 enablePRI_low = (adapter_control & CFSTERM);
1576 enablePRI_high = (adapter_control & CFWSTERM);
1577 }
1578 /* Make the table calculations below happy */
1579 internal50_present = 0;
1580 internal68_present = 1;
1581 externalcable_present = 1;
1582 } else if ((ahc->features & AHC_SPIOCAP) != 0) {
1583 aic785X_cable_detect(ahc, &internal50_present,
1584 &externalcable_present,
1585 &eeprom_present);
1586 /* Can never support a wide connector. */
1587 internal68_present = 0;
1588 } else {
1589 aic787X_cable_detect(ahc, &internal50_present,
1590 &internal68_present,
1591 &externalcable_present,
1592 &eeprom_present);
1593 }
1594
1595 if ((ahc->features & AHC_WIDE) == 0)
1596 internal68_present = 0;
1597
1598 if (bootverbose
1599 && (ahc->features & AHC_ULTRA2) == 0) {
1600 printk("%s: internal 50 cable %s present",
1601 ahc_name(ahc),
1602 internal50_present ? "is":"not");
1603
1604 if ((ahc->features & AHC_WIDE) != 0)
1605 printk(", internal 68 cable %s present",
1606 internal68_present ? "is":"not");
1607 printk("\n%s: external cable %s present\n",
1608 ahc_name(ahc),
1609 externalcable_present ? "is":"not");
1610 }
1611 if (bootverbose)
1612 printk("%s: BIOS eeprom %s present\n",
1613 ahc_name(ahc), eeprom_present ? "is" : "not");
1614
1615 if ((ahc->flags & AHC_INT50_SPEEDFLEX) != 0) {
1616 /*
1617 * The 50 pin connector is a separate bus,
1618 * so force it to always be terminated.
1619 * In the future, perform current sensing
1620 * to determine if we are in the middle of
1621 * a properly terminated bus.
1622 */
1623 internal50_present = 0;
1624 }
1625
1626 /*
1627 * Now set the termination based on what
1628 * we found.
1629 * Flash Enable = BRDDAT7
1630 * Secondary High Term Enable = BRDDAT6
1631 * Secondary Low Term Enable = BRDDAT5 (7890)
1632 * Primary High Term Enable = BRDDAT4 (7890)
1633 */
1634 if ((ahc->features & AHC_ULTRA2) == 0
1635 && (internal50_present != 0)
1636 && (internal68_present != 0)
1637 && (externalcable_present != 0)) {
1638 printk("%s: Illegal cable configuration!!. "
1639 "Only two connectors on the "
1640 "adapter may be used at a "
1641 "time!\n", ahc_name(ahc));
1642
1643 /*
1644 * Pretend there are no cables in the hope
1645 * that having all of the termination on
1646 * gives us a more stable bus.
1647 */
1648 internal50_present = 0;
1649 internal68_present = 0;
1650 externalcable_present = 0;
1651 }
1652
1653 if ((ahc->features & AHC_WIDE) != 0
1654 && ((externalcable_present == 0)
1655 || (internal68_present == 0)
1656 || (enableSEC_high != 0))) {
1657 brddat |= BRDDAT6;
1658 if (bootverbose) {
1659 if ((ahc->flags & AHC_INT50_SPEEDFLEX) != 0)
1660 printk("%s: 68 pin termination "
1661 "Enabled\n", ahc_name(ahc));
1662 else
1663 printk("%s: %sHigh byte termination "
1664 "Enabled\n", ahc_name(ahc),
1665 enableSEC_high ? "Secondary "
1666 : "");
1667 }
1668 }
1669
1670 sum = internal50_present + internal68_present
1671 + externalcable_present;
1672 if (sum < 2 || (enableSEC_low != 0)) {
1673 if ((ahc->features & AHC_ULTRA2) != 0)
1674 brddat |= BRDDAT5;
1675 else
1676 *sxfrctl1 |= STPWEN;
1677 if (bootverbose) {
1678 if ((ahc->flags & AHC_INT50_SPEEDFLEX) != 0)
1679 printk("%s: 50 pin termination "
1680 "Enabled\n", ahc_name(ahc));
1681 else
1682 printk("%s: %sLow byte termination "
1683 "Enabled\n", ahc_name(ahc),
1684 enableSEC_low ? "Secondary "
1685 : "");
1686 }
1687 }
1688
1689 if (enablePRI_low != 0) {
1690 *sxfrctl1 |= STPWEN;
1691 if (bootverbose)
1692 printk("%s: Primary Low Byte termination "
1693 "Enabled\n", ahc_name(ahc));
1694 }
1695
1696 /*
1697 * Setup STPWEN before setting up the rest of
1698 * the termination per the tech note on the U160 cards.
1699 */
1700 ahc_outb(ahc, SXFRCTL1, *sxfrctl1);
1701
1702 if (enablePRI_high != 0) {
1703 brddat |= BRDDAT4;
1704 if (bootverbose)
1705 printk("%s: Primary High Byte "
1706 "termination Enabled\n",
1707 ahc_name(ahc));
1708 }
1709
1710 write_brdctl(ahc, brddat);
1711
1712 } else {
1713 if ((adapter_control & CFSTERM) != 0) {
1714 *sxfrctl1 |= STPWEN;
1715
1716 if (bootverbose)
1717 printk("%s: %sLow byte termination Enabled\n",
1718 ahc_name(ahc),
1719 (ahc->features & AHC_ULTRA2) ? "Primary "
1720 : "");
1721 }
1722
1723 if ((adapter_control & CFWSTERM) != 0
1724 && (ahc->features & AHC_WIDE) != 0) {
1725 brddat |= BRDDAT6;
1726 if (bootverbose)
1727 printk("%s: %sHigh byte termination Enabled\n",
1728 ahc_name(ahc),
1729 (ahc->features & AHC_ULTRA2)
1730 ? "Secondary " : "");
1731 }
1732
1733 /*
1734 * Setup STPWEN before setting up the rest of
1735 * the termination per the tech note on the U160 cards.
1736 */
1737 ahc_outb(ahc, SXFRCTL1, *sxfrctl1);
1738
1739 if ((ahc->features & AHC_WIDE) != 0)
1740 write_brdctl(ahc, brddat);
1741 }
1742 SEEPROM_OUTB(sd, sd->sd_MS); /* Clear CS */
1743 }
1744
1745 static void
ahc_new_term_detect(struct ahc_softc * ahc,int * enableSEC_low,int * enableSEC_high,int * enablePRI_low,int * enablePRI_high,int * eeprom_present)1746 ahc_new_term_detect(struct ahc_softc *ahc, int *enableSEC_low,
1747 int *enableSEC_high, int *enablePRI_low,
1748 int *enablePRI_high, int *eeprom_present)
1749 {
1750 uint8_t brdctl;
1751
1752 /*
1753 * BRDDAT7 = Eeprom
1754 * BRDDAT6 = Enable Secondary High Byte termination
1755 * BRDDAT5 = Enable Secondary Low Byte termination
1756 * BRDDAT4 = Enable Primary high byte termination
1757 * BRDDAT3 = Enable Primary low byte termination
1758 */
1759 brdctl = read_brdctl(ahc);
1760 *eeprom_present = brdctl & BRDDAT7;
1761 *enableSEC_high = (brdctl & BRDDAT6);
1762 *enableSEC_low = (brdctl & BRDDAT5);
1763 *enablePRI_high = (brdctl & BRDDAT4);
1764 *enablePRI_low = (brdctl & BRDDAT3);
1765 }
1766
1767 static void
aic787X_cable_detect(struct ahc_softc * ahc,int * internal50_present,int * internal68_present,int * externalcable_present,int * eeprom_present)1768 aic787X_cable_detect(struct ahc_softc *ahc, int *internal50_present,
1769 int *internal68_present, int *externalcable_present,
1770 int *eeprom_present)
1771 {
1772 uint8_t brdctl;
1773
1774 /*
1775 * First read the status of our cables.
1776 * Set the rom bank to 0 since the
1777 * bank setting serves as a multiplexor
1778 * for the cable detection logic.
1779 * BRDDAT5 controls the bank switch.
1780 */
1781 write_brdctl(ahc, 0);
1782
1783 /*
1784 * Now read the state of the internal
1785 * connectors. BRDDAT6 is INT50 and
1786 * BRDDAT7 is INT68.
1787 */
1788 brdctl = read_brdctl(ahc);
1789 *internal50_present = (brdctl & BRDDAT6) ? 0 : 1;
1790 *internal68_present = (brdctl & BRDDAT7) ? 0 : 1;
1791
1792 /*
1793 * Set the rom bank to 1 and determine
1794 * the other signals.
1795 */
1796 write_brdctl(ahc, BRDDAT5);
1797
1798 /*
1799 * Now read the state of the external
1800 * connectors. BRDDAT6 is EXT68 and
1801 * BRDDAT7 is EPROMPS.
1802 */
1803 brdctl = read_brdctl(ahc);
1804 *externalcable_present = (brdctl & BRDDAT6) ? 0 : 1;
1805 *eeprom_present = (brdctl & BRDDAT7) ? 1 : 0;
1806 }
1807
1808 static void
aic785X_cable_detect(struct ahc_softc * ahc,int * internal50_present,int * externalcable_present,int * eeprom_present)1809 aic785X_cable_detect(struct ahc_softc *ahc, int *internal50_present,
1810 int *externalcable_present, int *eeprom_present)
1811 {
1812 uint8_t brdctl;
1813 uint8_t spiocap;
1814
1815 spiocap = ahc_inb(ahc, SPIOCAP);
1816 spiocap &= ~SOFTCMDEN;
1817 spiocap |= EXT_BRDCTL;
1818 ahc_outb(ahc, SPIOCAP, spiocap);
1819 ahc_outb(ahc, BRDCTL, BRDRW|BRDCS);
1820 ahc_flush_device_writes(ahc);
1821 ahc_delay(500);
1822 ahc_outb(ahc, BRDCTL, 0);
1823 ahc_flush_device_writes(ahc);
1824 ahc_delay(500);
1825 brdctl = ahc_inb(ahc, BRDCTL);
1826 *internal50_present = (brdctl & BRDDAT5) ? 0 : 1;
1827 *externalcable_present = (brdctl & BRDDAT6) ? 0 : 1;
1828 *eeprom_present = (ahc_inb(ahc, SPIOCAP) & EEPROM) ? 1 : 0;
1829 }
1830
1831 int
ahc_acquire_seeprom(struct ahc_softc * ahc,struct seeprom_descriptor * sd)1832 ahc_acquire_seeprom(struct ahc_softc *ahc, struct seeprom_descriptor *sd)
1833 {
1834 int wait;
1835
1836 if ((ahc->features & AHC_SPIOCAP) != 0
1837 && (ahc_inb(ahc, SPIOCAP) & SEEPROM) == 0)
1838 return (0);
1839
1840 /*
1841 * Request access of the memory port. When access is
1842 * granted, SEERDY will go high. We use a 1 second
1843 * timeout which should be near 1 second more than
1844 * is needed. Reason: after the chip reset, there
1845 * should be no contention.
1846 */
1847 SEEPROM_OUTB(sd, sd->sd_MS);
1848 wait = 1000; /* 1 second timeout in msec */
1849 while (--wait && ((SEEPROM_STATUS_INB(sd) & sd->sd_RDY) == 0)) {
1850 ahc_delay(1000); /* delay 1 msec */
1851 }
1852 if ((SEEPROM_STATUS_INB(sd) & sd->sd_RDY) == 0) {
1853 SEEPROM_OUTB(sd, 0);
1854 return (0);
1855 }
1856 return(1);
1857 }
1858
1859 void
ahc_release_seeprom(struct seeprom_descriptor * sd)1860 ahc_release_seeprom(struct seeprom_descriptor *sd)
1861 {
1862 /* Release access to the memory port and the serial EEPROM. */
1863 SEEPROM_OUTB(sd, 0);
1864 }
1865
1866 static void
write_brdctl(struct ahc_softc * ahc,uint8_t value)1867 write_brdctl(struct ahc_softc *ahc, uint8_t value)
1868 {
1869 uint8_t brdctl;
1870
1871 if ((ahc->chip & AHC_CHIPID_MASK) == AHC_AIC7895) {
1872 brdctl = BRDSTB;
1873 if (ahc->channel == 'B')
1874 brdctl |= BRDCS;
1875 } else if ((ahc->features & AHC_ULTRA2) != 0) {
1876 brdctl = 0;
1877 } else {
1878 brdctl = BRDSTB|BRDCS;
1879 }
1880 ahc_outb(ahc, BRDCTL, brdctl);
1881 ahc_flush_device_writes(ahc);
1882 brdctl |= value;
1883 ahc_outb(ahc, BRDCTL, brdctl);
1884 ahc_flush_device_writes(ahc);
1885 if ((ahc->features & AHC_ULTRA2) != 0)
1886 brdctl |= BRDSTB_ULTRA2;
1887 else
1888 brdctl &= ~BRDSTB;
1889 ahc_outb(ahc, BRDCTL, brdctl);
1890 ahc_flush_device_writes(ahc);
1891 if ((ahc->features & AHC_ULTRA2) != 0)
1892 brdctl = 0;
1893 else
1894 brdctl &= ~BRDCS;
1895 ahc_outb(ahc, BRDCTL, brdctl);
1896 }
1897
1898 static uint8_t
read_brdctl(struct ahc_softc * ahc)1899 read_brdctl(struct ahc_softc *ahc)
1900 {
1901 uint8_t brdctl;
1902 uint8_t value;
1903
1904 if ((ahc->chip & AHC_CHIPID_MASK) == AHC_AIC7895) {
1905 brdctl = BRDRW;
1906 if (ahc->channel == 'B')
1907 brdctl |= BRDCS;
1908 } else if ((ahc->features & AHC_ULTRA2) != 0) {
1909 brdctl = BRDRW_ULTRA2;
1910 } else {
1911 brdctl = BRDRW|BRDCS;
1912 }
1913 ahc_outb(ahc, BRDCTL, brdctl);
1914 ahc_flush_device_writes(ahc);
1915 value = ahc_inb(ahc, BRDCTL);
1916 ahc_outb(ahc, BRDCTL, 0);
1917 return (value);
1918 }
1919
1920 static void
ahc_pci_intr(struct ahc_softc * ahc)1921 ahc_pci_intr(struct ahc_softc *ahc)
1922 {
1923 u_int error;
1924 u_int status1;
1925
1926 error = ahc_inb(ahc, ERROR);
1927 if ((error & PCIERRSTAT) == 0)
1928 return;
1929
1930 status1 = ahc_pci_read_config(ahc->dev_softc,
1931 PCIR_STATUS + 1, /*bytes*/1);
1932
1933 printk("%s: PCI error Interrupt at seqaddr = 0x%x\n",
1934 ahc_name(ahc),
1935 ahc_inb(ahc, SEQADDR0) | (ahc_inb(ahc, SEQADDR1) << 8));
1936
1937 if (status1 & DPE) {
1938 ahc->pci_target_perr_count++;
1939 printk("%s: Data Parity Error Detected during address "
1940 "or write data phase\n", ahc_name(ahc));
1941 }
1942 if (status1 & SSE) {
1943 printk("%s: Signal System Error Detected\n", ahc_name(ahc));
1944 }
1945 if (status1 & RMA) {
1946 printk("%s: Received a Master Abort\n", ahc_name(ahc));
1947 }
1948 if (status1 & RTA) {
1949 printk("%s: Received a Target Abort\n", ahc_name(ahc));
1950 }
1951 if (status1 & STA) {
1952 printk("%s: Signaled a Target Abort\n", ahc_name(ahc));
1953 }
1954 if (status1 & DPR) {
1955 printk("%s: Data Parity Error has been reported via PERR#\n",
1956 ahc_name(ahc));
1957 }
1958
1959 /* Clear latched errors. */
1960 ahc_pci_write_config(ahc->dev_softc, PCIR_STATUS + 1,
1961 status1, /*bytes*/1);
1962
1963 if ((status1 & (DPE|SSE|RMA|RTA|STA|DPR)) == 0) {
1964 printk("%s: Latched PCIERR interrupt with "
1965 "no status bits set\n", ahc_name(ahc));
1966 } else {
1967 ahc_outb(ahc, CLRINT, CLRPARERR);
1968 }
1969
1970 if (ahc->pci_target_perr_count > AHC_PCI_TARGET_PERR_THRESH) {
1971 printk(
1972 "%s: WARNING WARNING WARNING WARNING\n"
1973 "%s: Too many PCI parity errors observed as a target.\n"
1974 "%s: Some device on this bus is generating bad parity.\n"
1975 "%s: This is an error *observed by*, not *generated by*, this controller.\n"
1976 "%s: PCI parity error checking has been disabled.\n"
1977 "%s: WARNING WARNING WARNING WARNING\n",
1978 ahc_name(ahc), ahc_name(ahc), ahc_name(ahc),
1979 ahc_name(ahc), ahc_name(ahc), ahc_name(ahc));
1980 ahc->seqctl |= FAILDIS;
1981 ahc_outb(ahc, SEQCTL, ahc->seqctl);
1982 }
1983 ahc_unpause(ahc);
1984 }
1985
1986 static int
ahc_pci_chip_init(struct ahc_softc * ahc)1987 ahc_pci_chip_init(struct ahc_softc *ahc)
1988 {
1989 ahc_outb(ahc, DSCOMMAND0, ahc->bus_softc.pci_softc.dscommand0);
1990 ahc_outb(ahc, DSPCISTATUS, ahc->bus_softc.pci_softc.dspcistatus);
1991 if ((ahc->features & AHC_DT) != 0) {
1992 u_int sfunct;
1993
1994 sfunct = ahc_inb(ahc, SFUNCT) & ~ALT_MODE;
1995 ahc_outb(ahc, SFUNCT, sfunct | ALT_MODE);
1996 ahc_outb(ahc, OPTIONMODE, ahc->bus_softc.pci_softc.optionmode);
1997 ahc_outw(ahc, TARGCRCCNT, ahc->bus_softc.pci_softc.targcrccnt);
1998 ahc_outb(ahc, SFUNCT, sfunct);
1999 ahc_outb(ahc, CRCCONTROL1,
2000 ahc->bus_softc.pci_softc.crccontrol1);
2001 }
2002 if ((ahc->features & AHC_MULTI_FUNC) != 0)
2003 ahc_outb(ahc, SCBBADDR, ahc->bus_softc.pci_softc.scbbaddr);
2004
2005 if ((ahc->features & AHC_ULTRA2) != 0)
2006 ahc_outb(ahc, DFF_THRSH, ahc->bus_softc.pci_softc.dff_thrsh);
2007
2008 return (ahc_chip_init(ahc));
2009 }
2010
2011 #ifdef CONFIG_PM
2012 void
ahc_pci_resume(struct ahc_softc * ahc)2013 ahc_pci_resume(struct ahc_softc *ahc)
2014 {
2015 /*
2016 * We assume that the OS has restored our register
2017 * mappings, etc. Just update the config space registers
2018 * that the OS doesn't know about and rely on our chip
2019 * reset handler to handle the rest.
2020 */
2021 ahc_pci_write_config(ahc->dev_softc, DEVCONFIG,
2022 ahc->bus_softc.pci_softc.devconfig, /*bytes*/4);
2023 ahc_pci_write_config(ahc->dev_softc, PCIR_COMMAND,
2024 ahc->bus_softc.pci_softc.command, /*bytes*/1);
2025 ahc_pci_write_config(ahc->dev_softc, CSIZE_LATTIME,
2026 ahc->bus_softc.pci_softc.csize_lattime, /*bytes*/1);
2027 if ((ahc->flags & AHC_HAS_TERM_LOGIC) != 0) {
2028 struct seeprom_descriptor sd;
2029 u_int sxfrctl1;
2030
2031 sd.sd_ahc = ahc;
2032 sd.sd_control_offset = SEECTL;
2033 sd.sd_status_offset = SEECTL;
2034 sd.sd_dataout_offset = SEECTL;
2035
2036 ahc_acquire_seeprom(ahc, &sd);
2037 configure_termination(ahc, &sd,
2038 ahc->seep_config->adapter_control,
2039 &sxfrctl1);
2040 ahc_release_seeprom(&sd);
2041 }
2042 }
2043 #endif
2044
2045 static int
ahc_aic785X_setup(struct ahc_softc * ahc)2046 ahc_aic785X_setup(struct ahc_softc *ahc)
2047 {
2048 ahc_dev_softc_t pci;
2049 uint8_t rev;
2050
2051 pci = ahc->dev_softc;
2052 ahc->channel = 'A';
2053 ahc->chip = AHC_AIC7850;
2054 ahc->features = AHC_AIC7850_FE;
2055 ahc->bugs |= AHC_TMODE_WIDEODD_BUG|AHC_CACHETHEN_BUG|AHC_PCI_MWI_BUG;
2056 rev = ahc_pci_read_config(pci, PCIR_REVID, /*bytes*/1);
2057 if (rev >= 1)
2058 ahc->bugs |= AHC_PCI_2_1_RETRY_BUG;
2059 ahc->instruction_ram_size = 512;
2060 return (0);
2061 }
2062
2063 static int
ahc_aic7860_setup(struct ahc_softc * ahc)2064 ahc_aic7860_setup(struct ahc_softc *ahc)
2065 {
2066 ahc_dev_softc_t pci;
2067 uint8_t rev;
2068
2069 pci = ahc->dev_softc;
2070 ahc->channel = 'A';
2071 ahc->chip = AHC_AIC7860;
2072 ahc->features = AHC_AIC7860_FE;
2073 ahc->bugs |= AHC_TMODE_WIDEODD_BUG|AHC_CACHETHEN_BUG|AHC_PCI_MWI_BUG;
2074 rev = ahc_pci_read_config(pci, PCIR_REVID, /*bytes*/1);
2075 if (rev >= 1)
2076 ahc->bugs |= AHC_PCI_2_1_RETRY_BUG;
2077 ahc->instruction_ram_size = 512;
2078 return (0);
2079 }
2080
2081 static int
ahc_apa1480_setup(struct ahc_softc * ahc)2082 ahc_apa1480_setup(struct ahc_softc *ahc)
2083 {
2084 int error;
2085
2086 error = ahc_aic7860_setup(ahc);
2087 if (error != 0)
2088 return (error);
2089 ahc->features |= AHC_REMOVABLE;
2090 return (0);
2091 }
2092
2093 static int
ahc_aic7870_setup(struct ahc_softc * ahc)2094 ahc_aic7870_setup(struct ahc_softc *ahc)
2095 {
2096
2097 ahc->channel = 'A';
2098 ahc->chip = AHC_AIC7870;
2099 ahc->features = AHC_AIC7870_FE;
2100 ahc->bugs |= AHC_TMODE_WIDEODD_BUG|AHC_CACHETHEN_BUG|AHC_PCI_MWI_BUG;
2101 ahc->instruction_ram_size = 512;
2102 return (0);
2103 }
2104
2105 static int
ahc_aic7870h_setup(struct ahc_softc * ahc)2106 ahc_aic7870h_setup(struct ahc_softc *ahc)
2107 {
2108 int error = ahc_aic7870_setup(ahc);
2109
2110 ahc->features |= AHC_HVD;
2111
2112 return error;
2113 }
2114
2115 static int
ahc_aha394X_setup(struct ahc_softc * ahc)2116 ahc_aha394X_setup(struct ahc_softc *ahc)
2117 {
2118 int error;
2119
2120 error = ahc_aic7870_setup(ahc);
2121 if (error == 0)
2122 error = ahc_aha394XX_setup(ahc);
2123 return (error);
2124 }
2125
2126 static int
ahc_aha394Xh_setup(struct ahc_softc * ahc)2127 ahc_aha394Xh_setup(struct ahc_softc *ahc)
2128 {
2129 int error = ahc_aha394X_setup(ahc);
2130
2131 ahc->features |= AHC_HVD;
2132
2133 return error;
2134 }
2135
2136 static int
ahc_aha398X_setup(struct ahc_softc * ahc)2137 ahc_aha398X_setup(struct ahc_softc *ahc)
2138 {
2139 int error;
2140
2141 error = ahc_aic7870_setup(ahc);
2142 if (error == 0)
2143 error = ahc_aha398XX_setup(ahc);
2144 return (error);
2145 }
2146
2147 static int
ahc_aha494X_setup(struct ahc_softc * ahc)2148 ahc_aha494X_setup(struct ahc_softc *ahc)
2149 {
2150 int error;
2151
2152 error = ahc_aic7870_setup(ahc);
2153 if (error == 0)
2154 error = ahc_aha494XX_setup(ahc);
2155 return (error);
2156 }
2157
2158 static int
ahc_aha494Xh_setup(struct ahc_softc * ahc)2159 ahc_aha494Xh_setup(struct ahc_softc *ahc)
2160 {
2161 int error = ahc_aha494X_setup(ahc);
2162
2163 ahc->features |= AHC_HVD;
2164
2165 return error;
2166 }
2167
2168 static int
ahc_aic7880_setup(struct ahc_softc * ahc)2169 ahc_aic7880_setup(struct ahc_softc *ahc)
2170 {
2171 ahc_dev_softc_t pci;
2172 uint8_t rev;
2173
2174 pci = ahc->dev_softc;
2175 ahc->channel = 'A';
2176 ahc->chip = AHC_AIC7880;
2177 ahc->features = AHC_AIC7880_FE;
2178 ahc->bugs |= AHC_TMODE_WIDEODD_BUG;
2179 rev = ahc_pci_read_config(pci, PCIR_REVID, /*bytes*/1);
2180 if (rev >= 1) {
2181 ahc->bugs |= AHC_PCI_2_1_RETRY_BUG;
2182 } else {
2183 ahc->bugs |= AHC_CACHETHEN_BUG|AHC_PCI_MWI_BUG;
2184 }
2185 ahc->instruction_ram_size = 512;
2186 return (0);
2187 }
2188
2189 static int
ahc_aic7880h_setup(struct ahc_softc * ahc)2190 ahc_aic7880h_setup(struct ahc_softc *ahc)
2191 {
2192 int error = ahc_aic7880_setup(ahc);
2193
2194 ahc->features |= AHC_HVD;
2195
2196 return error;
2197 }
2198
2199
2200 static int
ahc_aha2940Pro_setup(struct ahc_softc * ahc)2201 ahc_aha2940Pro_setup(struct ahc_softc *ahc)
2202 {
2203
2204 ahc->flags |= AHC_INT50_SPEEDFLEX;
2205 return (ahc_aic7880_setup(ahc));
2206 }
2207
2208 static int
ahc_aha394XU_setup(struct ahc_softc * ahc)2209 ahc_aha394XU_setup(struct ahc_softc *ahc)
2210 {
2211 int error;
2212
2213 error = ahc_aic7880_setup(ahc);
2214 if (error == 0)
2215 error = ahc_aha394XX_setup(ahc);
2216 return (error);
2217 }
2218
2219 static int
ahc_aha394XUh_setup(struct ahc_softc * ahc)2220 ahc_aha394XUh_setup(struct ahc_softc *ahc)
2221 {
2222 int error = ahc_aha394XU_setup(ahc);
2223
2224 ahc->features |= AHC_HVD;
2225
2226 return error;
2227 }
2228
2229 static int
ahc_aha398XU_setup(struct ahc_softc * ahc)2230 ahc_aha398XU_setup(struct ahc_softc *ahc)
2231 {
2232 int error;
2233
2234 error = ahc_aic7880_setup(ahc);
2235 if (error == 0)
2236 error = ahc_aha398XX_setup(ahc);
2237 return (error);
2238 }
2239
2240 static int
ahc_aic7890_setup(struct ahc_softc * ahc)2241 ahc_aic7890_setup(struct ahc_softc *ahc)
2242 {
2243 ahc_dev_softc_t pci;
2244 uint8_t rev;
2245
2246 pci = ahc->dev_softc;
2247 ahc->channel = 'A';
2248 ahc->chip = AHC_AIC7890;
2249 ahc->features = AHC_AIC7890_FE;
2250 ahc->flags |= AHC_NEWEEPROM_FMT;
2251 rev = ahc_pci_read_config(pci, PCIR_REVID, /*bytes*/1);
2252 if (rev == 0)
2253 ahc->bugs |= AHC_AUTOFLUSH_BUG|AHC_CACHETHEN_BUG;
2254 ahc->instruction_ram_size = 768;
2255 return (0);
2256 }
2257
2258 static int
ahc_aic7892_setup(struct ahc_softc * ahc)2259 ahc_aic7892_setup(struct ahc_softc *ahc)
2260 {
2261
2262 ahc->channel = 'A';
2263 ahc->chip = AHC_AIC7892;
2264 ahc->features = AHC_AIC7892_FE;
2265 ahc->flags |= AHC_NEWEEPROM_FMT;
2266 ahc->bugs |= AHC_SCBCHAN_UPLOAD_BUG;
2267 ahc->instruction_ram_size = 1024;
2268 return (0);
2269 }
2270
2271 static int
ahc_aic7895_setup(struct ahc_softc * ahc)2272 ahc_aic7895_setup(struct ahc_softc *ahc)
2273 {
2274 ahc_dev_softc_t pci;
2275 uint8_t rev;
2276
2277 pci = ahc->dev_softc;
2278 ahc->channel = ahc_get_pci_function(pci) == 1 ? 'B' : 'A';
2279 /*
2280 * The 'C' revision of the aic7895 has a few additional features.
2281 */
2282 rev = ahc_pci_read_config(pci, PCIR_REVID, /*bytes*/1);
2283 if (rev >= 4) {
2284 ahc->chip = AHC_AIC7895C;
2285 ahc->features = AHC_AIC7895C_FE;
2286 } else {
2287 u_int command;
2288
2289 ahc->chip = AHC_AIC7895;
2290 ahc->features = AHC_AIC7895_FE;
2291
2292 /*
2293 * The BIOS disables the use of MWI transactions
2294 * since it does not have the MWI bug work around
2295 * we have. Disabling MWI reduces performance, so
2296 * turn it on again.
2297 */
2298 command = ahc_pci_read_config(pci, PCIR_COMMAND, /*bytes*/1);
2299 command |= PCIM_CMD_MWRICEN;
2300 ahc_pci_write_config(pci, PCIR_COMMAND, command, /*bytes*/1);
2301 ahc->bugs |= AHC_PCI_MWI_BUG;
2302 }
2303 /*
2304 * XXX Does CACHETHEN really not work??? What about PCI retry?
2305 * on C level chips. Need to test, but for now, play it safe.
2306 */
2307 ahc->bugs |= AHC_TMODE_WIDEODD_BUG|AHC_PCI_2_1_RETRY_BUG
2308 | AHC_CACHETHEN_BUG;
2309
2310 #if 0
2311 uint32_t devconfig;
2312
2313 /*
2314 * Cachesize must also be zero due to stray DAC
2315 * problem when sitting behind some bridges.
2316 */
2317 ahc_pci_write_config(pci, CSIZE_LATTIME, 0, /*bytes*/1);
2318 devconfig = ahc_pci_read_config(pci, DEVCONFIG, /*bytes*/1);
2319 devconfig |= MRDCEN;
2320 ahc_pci_write_config(pci, DEVCONFIG, devconfig, /*bytes*/1);
2321 #endif
2322 ahc->flags |= AHC_NEWEEPROM_FMT;
2323 ahc->instruction_ram_size = 512;
2324 return (0);
2325 }
2326
2327 static int
ahc_aic7895h_setup(struct ahc_softc * ahc)2328 ahc_aic7895h_setup(struct ahc_softc *ahc)
2329 {
2330 int error = ahc_aic7895_setup(ahc);
2331
2332 ahc->features |= AHC_HVD;
2333
2334 return error;
2335 }
2336
2337 static int
ahc_aic7896_setup(struct ahc_softc * ahc)2338 ahc_aic7896_setup(struct ahc_softc *ahc)
2339 {
2340 ahc_dev_softc_t pci;
2341
2342 pci = ahc->dev_softc;
2343 ahc->channel = ahc_get_pci_function(pci) == 1 ? 'B' : 'A';
2344 ahc->chip = AHC_AIC7896;
2345 ahc->features = AHC_AIC7896_FE;
2346 ahc->flags |= AHC_NEWEEPROM_FMT;
2347 ahc->bugs |= AHC_CACHETHEN_DIS_BUG;
2348 ahc->instruction_ram_size = 768;
2349 return (0);
2350 }
2351
2352 static int
ahc_aic7899_setup(struct ahc_softc * ahc)2353 ahc_aic7899_setup(struct ahc_softc *ahc)
2354 {
2355 ahc_dev_softc_t pci;
2356
2357 pci = ahc->dev_softc;
2358 ahc->channel = ahc_get_pci_function(pci) == 1 ? 'B' : 'A';
2359 ahc->chip = AHC_AIC7899;
2360 ahc->features = AHC_AIC7899_FE;
2361 ahc->flags |= AHC_NEWEEPROM_FMT;
2362 ahc->bugs |= AHC_SCBCHAN_UPLOAD_BUG;
2363 ahc->instruction_ram_size = 1024;
2364 return (0);
2365 }
2366
2367 static int
ahc_aha29160C_setup(struct ahc_softc * ahc)2368 ahc_aha29160C_setup(struct ahc_softc *ahc)
2369 {
2370 int error;
2371
2372 error = ahc_aic7899_setup(ahc);
2373 if (error != 0)
2374 return (error);
2375 ahc->features |= AHC_REMOVABLE;
2376 return (0);
2377 }
2378
2379 static int
ahc_raid_setup(struct ahc_softc * ahc)2380 ahc_raid_setup(struct ahc_softc *ahc)
2381 {
2382 printk("RAID functionality unsupported\n");
2383 return (ENXIO);
2384 }
2385
2386 static int
ahc_aha394XX_setup(struct ahc_softc * ahc)2387 ahc_aha394XX_setup(struct ahc_softc *ahc)
2388 {
2389 ahc_dev_softc_t pci;
2390
2391 pci = ahc->dev_softc;
2392 switch (ahc_get_pci_slot(pci)) {
2393 case AHC_394X_SLOT_CHANNEL_A:
2394 ahc->channel = 'A';
2395 break;
2396 case AHC_394X_SLOT_CHANNEL_B:
2397 ahc->channel = 'B';
2398 break;
2399 default:
2400 printk("adapter at unexpected slot %d\n"
2401 "unable to map to a channel\n",
2402 ahc_get_pci_slot(pci));
2403 ahc->channel = 'A';
2404 }
2405 return (0);
2406 }
2407
2408 static int
ahc_aha398XX_setup(struct ahc_softc * ahc)2409 ahc_aha398XX_setup(struct ahc_softc *ahc)
2410 {
2411 ahc_dev_softc_t pci;
2412
2413 pci = ahc->dev_softc;
2414 switch (ahc_get_pci_slot(pci)) {
2415 case AHC_398X_SLOT_CHANNEL_A:
2416 ahc->channel = 'A';
2417 break;
2418 case AHC_398X_SLOT_CHANNEL_B:
2419 ahc->channel = 'B';
2420 break;
2421 case AHC_398X_SLOT_CHANNEL_C:
2422 ahc->channel = 'C';
2423 break;
2424 default:
2425 printk("adapter at unexpected slot %d\n"
2426 "unable to map to a channel\n",
2427 ahc_get_pci_slot(pci));
2428 ahc->channel = 'A';
2429 break;
2430 }
2431 ahc->flags |= AHC_LARGE_SEEPROM;
2432 return (0);
2433 }
2434
2435 static int
ahc_aha494XX_setup(struct ahc_softc * ahc)2436 ahc_aha494XX_setup(struct ahc_softc *ahc)
2437 {
2438 ahc_dev_softc_t pci;
2439
2440 pci = ahc->dev_softc;
2441 switch (ahc_get_pci_slot(pci)) {
2442 case AHC_494X_SLOT_CHANNEL_A:
2443 ahc->channel = 'A';
2444 break;
2445 case AHC_494X_SLOT_CHANNEL_B:
2446 ahc->channel = 'B';
2447 break;
2448 case AHC_494X_SLOT_CHANNEL_C:
2449 ahc->channel = 'C';
2450 break;
2451 case AHC_494X_SLOT_CHANNEL_D:
2452 ahc->channel = 'D';
2453 break;
2454 default:
2455 printk("adapter at unexpected slot %d\n"
2456 "unable to map to a channel\n",
2457 ahc_get_pci_slot(pci));
2458 ahc->channel = 'A';
2459 }
2460 ahc->flags |= AHC_LARGE_SEEPROM;
2461 return (0);
2462 }
2463
