1# SPDX-License-Identifier: GPL-2.0-only
2#
3# SPI driver configuration
4#
5menuconfig SPI
6	bool "SPI support"
7	depends on HAS_IOMEM
8	help
9	  The "Serial Peripheral Interface" is a low level synchronous
10	  protocol.  Chips that support SPI can have data transfer rates
11	  up to several tens of Mbit/sec.  Chips are addressed with a
12	  controller and a chipselect.  Most SPI slaves don't support
13	  dynamic device discovery; some are even write-only or read-only.
14
15	  SPI is widely used by microcontrollers to talk with sensors,
16	  eeprom and flash memory, codecs and various other controller
17	  chips, analog to digital (and d-to-a) converters, and more.
18	  MMC and SD cards can be accessed using SPI protocol; and for
19	  DataFlash cards used in MMC sockets, SPI must always be used.
20
21	  SPI is one of a family of similar protocols using a four wire
22	  interface (select, clock, data in, data out) including Microwire
23	  (half duplex), SSP, SSI, and PSP.  This driver framework should
24	  work with most such devices and controllers.
25
26if SPI
27
28config SPI_DEBUG
29	bool "Debug support for SPI drivers"
30	depends on DEBUG_KERNEL
31	help
32	  Say "yes" to enable debug messaging (like dev_dbg and pr_debug),
33	  sysfs, and debugfs support in SPI controller and protocol drivers.
34
35#
36# MASTER side ... talking to discrete SPI slave chips including microcontrollers
37#
38
39config SPI_MASTER
40#	bool "SPI Master Support"
41	bool
42	default SPI
43	help
44	  If your system has an master-capable SPI controller (which
45	  provides the clock and chipselect), you can enable that
46	  controller and the protocol drivers for the SPI slave chips
47	  that are connected.
48
49if SPI_MASTER
50
51config SPI_MEM
52	bool "SPI memory extension"
53	help
54	  Enable this option if you want to enable the SPI memory extension.
55	  This extension is meant to simplify interaction with SPI memories
56	  by providing a high-level interface to send memory-like commands.
57
58comment "SPI Master Controller Drivers"
59
60config SPI_ALTERA
61	tristate "Altera SPI Controller"
62	help
63	  This is the driver for the Altera SPI Controller.
64
65config SPI_ATH79
66	tristate "Atheros AR71XX/AR724X/AR913X SPI controller driver"
67	depends on ATH79 || COMPILE_TEST
68	select SPI_BITBANG
69	help
70	  This enables support for the SPI controller present on the
71	  Atheros AR71XX/AR724X/AR913X SoCs.
72
73config SPI_ARMADA_3700
74	tristate "Marvell Armada 3700 SPI Controller"
75	depends on (ARCH_MVEBU && OF) || COMPILE_TEST
76	help
77	  This enables support for the SPI controller present on the
78	  Marvell Armada 3700 SoCs.
79
80config SPI_ATMEL
81	tristate "Atmel SPI Controller"
82	depends on ARCH_AT91 || COMPILE_TEST
83	help
84	  This selects a driver for the Atmel SPI Controller, present on
85	  many AT91 ARM chips.
86
87config SPI_AT91_USART
88	tristate "Atmel USART Controller SPI driver"
89	depends on (ARCH_AT91 || COMPILE_TEST)
90	depends on MFD_AT91_USART
91	help
92	  This selects a driver for the AT91 USART Controller as SPI Master,
93	  present on AT91 and SAMA5 SoC series.
94
95config SPI_ATMEL_QUADSPI
96	tristate "Atmel Quad SPI Controller"
97	depends on ARCH_AT91 || (ARM && COMPILE_TEST && !ARCH_EBSA110)
98	depends on OF && HAS_IOMEM
99	help
100	  This enables support for the Quad SPI controller in master mode.
101	  This driver does not support generic SPI. The implementation only
102	  supports spi-mem interface.
103
104config SPI_AU1550
105	tristate "Au1550/Au1200/Au1300 SPI Controller"
106	depends on MIPS_ALCHEMY
107	select SPI_BITBANG
108	help
109	  If you say yes to this option, support will be included for the
110	  PSC SPI controller found on Au1550, Au1200 and Au1300 series.
111
112config SPI_AXI_SPI_ENGINE
113	tristate "Analog Devices AXI SPI Engine controller"
114	depends on HAS_IOMEM
115	help
116	  This enables support for the Analog Devices AXI SPI Engine SPI controller.
117	  It is part of the SPI Engine framework that is used in some Analog Devices
118	  reference designs for FPGAs.
119
120config SPI_BCM2835
121	tristate "BCM2835 SPI controller"
122	depends on GPIOLIB
123	depends on ARCH_BCM2835 || ARCH_BRCMSTB || COMPILE_TEST
124	help
125	  This selects a driver for the Broadcom BCM2835 SPI master.
126
127	  The BCM2835 contains two types of SPI master controller; the
128	  "universal SPI master", and the regular SPI controller. This driver
129	  is for the regular SPI controller. Slave mode operation is not also
130	  not supported.
131
132config SPI_BCM2835AUX
133	tristate "BCM2835 SPI auxiliary controller"
134	depends on ((ARCH_BCM2835 || ARCH_BRCMSTB) && GPIOLIB) || COMPILE_TEST
135	help
136	  This selects a driver for the Broadcom BCM2835 SPI aux master.
137
138	  The BCM2835 contains two types of SPI master controller; the
139	  "universal SPI master", and the regular SPI controller.
140	  This driver is for the universal/auxiliary SPI controller.
141
142config SPI_BCM63XX
143	tristate "Broadcom BCM63xx SPI controller"
144	depends on BCM63XX || COMPILE_TEST
145	help
146          Enable support for the SPI controller on the Broadcom BCM63xx SoCs.
147
148config SPI_BCM63XX_HSSPI
149	tristate "Broadcom BCM63XX HS SPI controller driver"
150	depends on BCM63XX || ARCH_BCM_63XX || COMPILE_TEST
151	help
152	  This enables support for the High Speed SPI controller present on
153	  newer Broadcom BCM63XX SoCs.
154
155config SPI_BCM_QSPI
156	tristate "Broadcom BSPI and MSPI controller support"
157	depends on ARCH_BRCMSTB || ARCH_BCM || ARCH_BCM_IPROC || \
158			BMIPS_GENERIC || COMPILE_TEST
159	default ARCH_BCM_IPROC
160	help
161	  Enables support for the Broadcom SPI flash and MSPI controller.
162	  Select this option for any one of BRCMSTB, iProc NSP and NS2 SoCs
163	  based platforms. This driver works for both SPI master for spi-nor
164	  flash device as well as MSPI device.
165
166config SPI_BITBANG
167	tristate "Utilities for Bitbanging SPI masters"
168	help
169	  With a few GPIO pins, your system can bitbang the SPI protocol.
170	  Select this to get SPI support through I/O pins (GPIO, parallel
171	  port, etc).  Or, some systems' SPI master controller drivers use
172	  this code to manage the per-word or per-transfer accesses to the
173	  hardware shift registers.
174
175	  This is library code, and is automatically selected by drivers that
176	  need it.  You only need to select this explicitly to support driver
177	  modules that aren't part of this kernel tree.
178
179config SPI_BUTTERFLY
180	tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)"
181	depends on PARPORT
182	select SPI_BITBANG
183	help
184	  This uses a custom parallel port cable to connect to an AVR
185	  Butterfly <http://www.atmel.com/products/avr/butterfly>, an
186	  inexpensive battery powered microcontroller evaluation board.
187	  This same cable can be used to flash new firmware.
188
189config SPI_CADENCE
190	tristate "Cadence SPI controller"
191	help
192	  This selects the Cadence SPI controller master driver
193	  used by Xilinx Zynq and ZynqMP.
194
195config SPI_CLPS711X
196	tristate "CLPS711X host SPI controller"
197	depends on ARCH_CLPS711X || COMPILE_TEST
198	help
199	  This enables dedicated general purpose SPI/Microwire1-compatible
200	  master mode interface (SSI1) for CLPS711X-based CPUs.
201
202config SPI_COLDFIRE_QSPI
203	tristate "Freescale Coldfire QSPI controller"
204	depends on (M520x || M523x || M5249 || M525x || M527x || M528x || M532x)
205	help
206	  This enables support for the Coldfire QSPI controller in master
207	  mode.
208
209config SPI_DAVINCI
210	tristate "Texas Instruments DaVinci/DA8x/OMAP-L/AM1x SoC SPI controller"
211	depends on ARCH_DAVINCI || ARCH_KEYSTONE
212	select SPI_BITBANG
213	help
214	  SPI master controller for DaVinci/DA8x/OMAP-L/AM1x SPI modules.
215
216config SPI_DESIGNWARE
217	tristate "DesignWare SPI controller core support"
218	help
219	  general driver for SPI controller core from DesignWare
220
221config SPI_DW_PCI
222	tristate "PCI interface driver for DW SPI core"
223	depends on SPI_DESIGNWARE && PCI
224
225config SPI_DW_MID_DMA
226	bool "DMA support for DW SPI controller on Intel MID platform"
227	depends on SPI_DW_PCI && DW_DMAC_PCI
228
229config SPI_DW_MMIO
230	tristate "Memory-mapped io interface driver for DW SPI core"
231	depends on SPI_DESIGNWARE
232
233config SPI_DLN2
234       tristate "Diolan DLN-2 USB SPI adapter"
235       depends on MFD_DLN2
236       help
237         If you say yes to this option, support will be included for Diolan
238         DLN2, a USB to SPI interface.
239
240         This driver can also be built as a module.  If so, the module
241         will be called spi-dln2.
242
243config SPI_EFM32
244	tristate "EFM32 SPI controller"
245	depends on OF && ARM && (ARCH_EFM32 || COMPILE_TEST)
246	select SPI_BITBANG
247	help
248	  Driver for the spi controller found on Energy Micro's EFM32 SoCs.
249
250config SPI_EP93XX
251	tristate "Cirrus Logic EP93xx SPI controller"
252	depends on ARCH_EP93XX || COMPILE_TEST
253	help
254	  This enables using the Cirrus EP93xx SPI controller in master
255	  mode.
256
257config SPI_FALCON
258	bool "Falcon SPI controller support"
259	depends on SOC_FALCON
260	help
261	  The external bus unit (EBU) found on the FALC-ON SoC has SPI
262	  emulation that is designed for serial flash access. This driver
263	  has only been tested with m25p80 type chips. The hardware has no
264	  support for other types of SPI peripherals.
265
266config SPI_FSL_LPSPI
267	tristate "Freescale i.MX LPSPI controller"
268	depends on ARCH_MXC || COMPILE_TEST
269	help
270	  This enables Freescale i.MX LPSPI controllers in master mode.
271
272config SPI_FSL_QUADSPI
273	tristate "Freescale QSPI controller"
274	depends on ARCH_MXC || SOC_LS1021A || ARCH_LAYERSCAPE || COMPILE_TEST
275	depends on HAS_IOMEM
276	help
277	  This enables support for the Quad SPI controller in master mode.
278	  Up to four flash chips can be connected on two buses with two
279	  chipselects each.
280	  This controller does not support generic SPI messages. It only
281	  supports the high-level SPI memory interface.
282
283config SPI_NXP_FLEXSPI
284	tristate "NXP Flex SPI controller"
285	depends on ARCH_LAYERSCAPE || HAS_IOMEM
286	help
287	  This enables support for the Flex SPI controller in master mode.
288	  Up to four slave devices can be connected on two buses with two
289	  chipselects each.
290	  This controller does not support generic SPI messages and only
291	  supports the high-level SPI memory interface.
292
293config SPI_GPIO
294	tristate "GPIO-based bitbanging SPI Master"
295	depends on GPIOLIB || COMPILE_TEST
296	select SPI_BITBANG
297	help
298	  This simple GPIO bitbanging SPI master uses the arch-neutral GPIO
299	  interface to manage MOSI, MISO, SCK, and chipselect signals.  SPI
300	  slaves connected to a bus using this driver are configured as usual,
301	  except that the spi_board_info.controller_data holds the GPIO number
302	  for the chipselect used by this controller driver.
303
304	  Note that this driver often won't achieve even 1 Mbit/sec speeds,
305	  making it unusually slow for SPI.  If your platform can inline
306	  GPIO operations, you should be able to leverage that for better
307	  speed with a custom version of this driver; see the source code.
308
309config SPI_IMG_SPFI
310	tristate "IMG SPFI controller"
311	depends on MIPS || COMPILE_TEST
312	help
313	  This enables support for the SPFI master controller found on
314	  IMG SoCs.
315
316config SPI_IMX
317	tristate "Freescale i.MX SPI controllers"
318	depends on ARCH_MXC || COMPILE_TEST
319	select SPI_BITBANG
320	help
321	  This enables support for the Freescale i.MX SPI controllers.
322
323config SPI_JCORE
324	tristate "J-Core SPI Master"
325	depends on OF && (SUPERH || COMPILE_TEST)
326	help
327	  This enables support for the SPI master controller in the J-Core
328	  synthesizable, open source SoC.
329
330config SPI_LM70_LLP
331	tristate "Parallel port adapter for LM70 eval board (DEVELOPMENT)"
332	depends on PARPORT
333	select SPI_BITBANG
334	help
335	  This driver supports the NS LM70 LLP Evaluation Board,
336	  which interfaces to an LM70 temperature sensor using
337	  a parallel port.
338
339config SPI_LP8841_RTC
340	tristate "ICP DAS LP-8841 SPI Controller for RTC"
341	depends on MACH_PXA27X_DT || COMPILE_TEST
342	help
343	  This driver provides an SPI master device to drive Maxim
344	  DS-1302 real time clock.
345
346	  Say N here unless you plan to run the kernel on an ICP DAS
347	  LP-8x4x industrial computer.
348
349config SPI_MPC52xx
350	tristate "Freescale MPC52xx SPI (non-PSC) controller support"
351	depends on PPC_MPC52xx
352	help
353	  This drivers supports the MPC52xx SPI controller in master SPI
354	  mode.
355
356config SPI_MPC52xx_PSC
357	tristate "Freescale MPC52xx PSC SPI controller"
358	depends on PPC_MPC52xx
359	help
360	  This enables using the Freescale MPC52xx Programmable Serial
361	  Controller in master SPI mode.
362
363config SPI_MPC512x_PSC
364	tristate "Freescale MPC512x PSC SPI controller"
365	depends on PPC_MPC512x
366	help
367	  This enables using the Freescale MPC5121 Programmable Serial
368	  Controller in SPI master mode.
369
370config SPI_FSL_LIB
371	tristate
372	depends on OF
373
374config SPI_FSL_CPM
375	tristate
376	depends on FSL_SOC
377
378config SPI_FSL_SPI
379	tristate "Freescale SPI controller and Aeroflex Gaisler GRLIB SPI controller"
380	depends on OF
381	select SPI_FSL_LIB
382	select SPI_FSL_CPM if FSL_SOC
383	help
384	  This enables using the Freescale SPI controllers in master mode.
385	  MPC83xx platform uses the controller in cpu mode or CPM/QE mode.
386	  MPC8569 uses the controller in QE mode, MPC8610 in cpu mode.
387	  This also enables using the Aeroflex Gaisler GRLIB SPI controller in
388	  master mode.
389
390config SPI_FSL_DSPI
391	tristate "Freescale DSPI controller"
392	select REGMAP_MMIO
393	depends on SOC_VF610 || SOC_LS1021A || ARCH_LAYERSCAPE || M5441x || COMPILE_TEST
394	help
395	  This enables support for the Freescale DSPI controller in master
396	  mode. VF610, LS1021A and ColdFire platforms uses the controller.
397
398config SPI_FSL_ESPI
399	tristate "Freescale eSPI controller"
400	depends on FSL_SOC
401	help
402	  This enables using the Freescale eSPI controllers in master mode.
403	  From MPC8536, 85xx platform uses the controller, and all P10xx,
404	  P20xx, P30xx,P40xx, P50xx uses this controller.
405
406config SPI_MESON_SPICC
407	tristate "Amlogic Meson SPICC controller"
408	depends on ARCH_MESON || COMPILE_TEST
409	help
410	  This enables master mode support for the SPICC (SPI communication
411	  controller) available in Amlogic Meson SoCs.
412
413config SPI_MESON_SPIFC
414	tristate "Amlogic Meson SPIFC controller"
415	depends on ARCH_MESON || COMPILE_TEST
416	select REGMAP_MMIO
417	help
418	  This enables master mode support for the SPIFC (SPI flash
419	  controller) available in Amlogic Meson SoCs.
420
421config SPI_MT65XX
422	tristate "MediaTek SPI controller"
423	depends on ARCH_MEDIATEK || COMPILE_TEST
424	help
425	  This selects the MediaTek(R) SPI bus driver.
426	  If you want to use MediaTek(R) SPI interface,
427	  say Y or M here.If you are not sure, say N.
428	  SPI drivers for Mediatek MT65XX and MT81XX series ARM SoCs.
429
430config SPI_MT7621
431	tristate "MediaTek MT7621 SPI Controller"
432	depends on RALINK || COMPILE_TEST
433	help
434	  This selects a driver for the MediaTek MT7621 SPI Controller.
435
436config SPI_NPCM_FIU
437	tristate "Nuvoton NPCM FLASH Interface Unit"
438	depends on ARCH_NPCM || COMPILE_TEST
439	depends on OF && HAS_IOMEM
440	help
441	  This enables support for the Flash Interface Unit SPI controller
442	  in master mode.
443	  This driver does not support generic SPI. The implementation only
444	  supports spi-mem interface.
445
446config SPI_NPCM_PSPI
447	tristate "Nuvoton NPCM PSPI Controller"
448	depends on ARCH_NPCM || COMPILE_TEST
449	help
450	  This driver provides support for Nuvoton NPCM BMC
451	  Peripheral SPI controller in master mode.
452
453config SPI_LANTIQ_SSC
454	tristate "Lantiq SSC SPI controller"
455	depends on LANTIQ || COMPILE_TEST
456	help
457	  This driver supports the Lantiq SSC SPI controller in master
458	  mode. This controller is found on Intel (former Lantiq) SoCs like
459	  the Danube, Falcon, xRX200, xRX300.
460
461config SPI_OC_TINY
462	tristate "OpenCores tiny SPI"
463	depends on GPIOLIB || COMPILE_TEST
464	select SPI_BITBANG
465	help
466	  This is the driver for OpenCores tiny SPI master controller.
467
468config SPI_OCTEON
469	tristate "Cavium OCTEON SPI controller"
470	depends on CAVIUM_OCTEON_SOC
471	help
472	  SPI host driver for the hardware found on some Cavium OCTEON
473	  SOCs.
474
475config SPI_OMAP_UWIRE
476	tristate "OMAP1 MicroWire"
477	depends on ARCH_OMAP1
478	select SPI_BITBANG
479	help
480	  This hooks up to the MicroWire controller on OMAP1 chips.
481
482config SPI_OMAP24XX
483	tristate "McSPI driver for OMAP"
484	depends on ARCH_OMAP2PLUS || ARCH_K3 || COMPILE_TEST
485	select SG_SPLIT
486	help
487	  SPI master controller for OMAP24XX and later Multichannel SPI
488	  (McSPI) modules.
489
490config SPI_TI_QSPI
491	tristate "DRA7xxx QSPI controller support"
492	depends on ARCH_OMAP2PLUS || COMPILE_TEST
493	help
494	  QSPI master controller for DRA7xxx used for flash devices.
495	  This device supports single, dual and quad read support, while
496	  it only supports single write mode.
497
498config SPI_OMAP_100K
499	tristate "OMAP SPI 100K"
500	depends on ARCH_OMAP850 || ARCH_OMAP730 || COMPILE_TEST
501	help
502	  OMAP SPI 100K master controller for omap7xx boards.
503
504config SPI_ORION
505	tristate "Orion SPI master"
506	depends on PLAT_ORION || ARCH_MVEBU || COMPILE_TEST
507	help
508	  This enables using the SPI master controller on the Orion
509	  and MVEBU chips.
510
511config SPI_PIC32
512	tristate "Microchip PIC32 series SPI"
513	depends on MACH_PIC32 || COMPILE_TEST
514	help
515	  SPI driver for Microchip PIC32 SPI master controller.
516
517config SPI_PIC32_SQI
518	tristate "Microchip PIC32 Quad SPI driver"
519	depends on MACH_PIC32 || COMPILE_TEST
520	help
521	  SPI driver for PIC32 Quad SPI controller.
522
523config SPI_PL022
524	tristate "ARM AMBA PL022 SSP controller"
525	depends on ARM_AMBA
526	default y if MACH_U300
527	default y if ARCH_REALVIEW
528	default y if INTEGRATOR_IMPD1
529	default y if ARCH_VERSATILE
530	help
531	  This selects the ARM(R) AMBA(R) PrimeCell PL022 SSP
532	  controller. If you have an embedded system with an AMBA(R)
533	  bus and a PL022 controller, say Y or M here.
534
535config SPI_PPC4xx
536	tristate "PPC4xx SPI Controller"
537	depends on PPC32 && 4xx
538	select SPI_BITBANG
539	help
540	  This selects a driver for the PPC4xx SPI Controller.
541
542config SPI_PXA2XX
543	tristate "PXA2xx SSP SPI master"
544	depends on (ARCH_PXA || ARCH_MMP || PCI || ACPI)
545	select PXA_SSP if ARCH_PXA || ARCH_MMP
546	help
547	  This enables using a PXA2xx or Sodaville SSP port as a SPI master
548	  controller. The driver can be configured to use any SSP port and
549	  additional documentation can be found a Documentation/spi/pxa2xx.rst.
550
551config SPI_PXA2XX_PCI
552	def_tristate SPI_PXA2XX && PCI && COMMON_CLK
553
554config SPI_ROCKCHIP
555	tristate "Rockchip SPI controller driver"
556	help
557	  This selects a driver for Rockchip SPI controller.
558
559	  If you say yes to this option, support will be included for
560	  RK3066, RK3188 and RK3288 families of SPI controller.
561	  Rockchip SPI controller support DMA transport and PIO mode.
562	  The main usecase of this controller is to use spi flash as boot
563	  device.
564
565config SPI_RB4XX
566	tristate "Mikrotik RB4XX SPI master"
567	depends on SPI_MASTER && ATH79
568	help
569	  SPI controller driver for the Mikrotik RB4xx series boards.
570
571config SPI_RSPI
572	tristate "Renesas RSPI/QSPI controller"
573	depends on SUPERH || ARCH_RENESAS || COMPILE_TEST
574	help
575	  SPI driver for Renesas RSPI and QSPI blocks.
576
577config SPI_QCOM_QSPI
578	tristate "QTI QSPI controller"
579	depends on ARCH_QCOM
580	help
581	  QSPI(Quad SPI) driver for Qualcomm QSPI controller.
582
583config SPI_QUP
584	tristate "Qualcomm SPI controller with QUP interface"
585	depends on ARCH_QCOM || (ARM && COMPILE_TEST)
586	help
587	  Qualcomm Universal Peripheral (QUP) core is an AHB slave that
588	  provides a common data path (an output FIFO and an input FIFO)
589	  for serial peripheral interface (SPI) mini-core. SPI in master
590	  mode supports up to 50MHz, up to four chip selects, programmable
591	  data path from 4 bits to 32 bits and numerous protocol variants.
592
593	  This driver can also be built as a module.  If so, the module
594	  will be called spi_qup.
595
596config SPI_QCOM_GENI
597	tristate "Qualcomm GENI based SPI controller"
598	depends on QCOM_GENI_SE
599	help
600	  This driver supports GENI serial engine based SPI controller in
601	  master mode on the Qualcomm Technologies Inc.'s SoCs. If you say
602	  yes to this option, support will be included for the built-in SPI
603	  interface on the Qualcomm Technologies Inc.'s SoCs.
604
605	  This driver can also be built as a module.  If so, the module
606	  will be called spi-geni-qcom.
607
608config SPI_S3C24XX
609	tristate "Samsung S3C24XX series SPI"
610	depends on ARCH_S3C24XX
611	select SPI_BITBANG
612	help
613	  SPI driver for Samsung S3C24XX series ARM SoCs
614
615config SPI_S3C24XX_FIQ
616	bool "S3C24XX driver with FIQ pseudo-DMA"
617	depends on SPI_S3C24XX
618	select FIQ
619	help
620	  Enable FIQ support for the S3C24XX SPI driver to provide pseudo
621	  DMA by using the fast-interrupt request framework, This allows
622	  the driver to get DMA-like performance when there are either
623	  no free DMA channels, or when doing transfers that required both
624	  TX and RX data paths.
625
626config SPI_S3C64XX
627	tristate "Samsung S3C64XX series type SPI"
628	depends on (PLAT_SAMSUNG || ARCH_EXYNOS || COMPILE_TEST)
629	help
630	  SPI driver for Samsung S3C64XX and newer SoCs.
631
632config SPI_SC18IS602
633	tristate "NXP SC18IS602/602B/603 I2C to SPI bridge"
634	depends on I2C
635	help
636	  SPI driver for NXP SC18IS602/602B/603 I2C to SPI bridge.
637
638config SPI_SH_MSIOF
639	tristate "SuperH MSIOF SPI controller"
640	depends on HAVE_CLK
641	depends on ARCH_SHMOBILE || ARCH_RENESAS || COMPILE_TEST
642	help
643	  SPI driver for SuperH and SH Mobile MSIOF blocks.
644
645config SPI_SH
646	tristate "SuperH SPI controller"
647	depends on SUPERH || COMPILE_TEST
648	help
649	  SPI driver for SuperH SPI blocks.
650
651config SPI_SH_SCI
652	tristate "SuperH SCI SPI controller"
653	depends on SUPERH
654	select SPI_BITBANG
655	help
656	  SPI driver for SuperH SCI blocks.
657
658config SPI_SH_HSPI
659	tristate "SuperH HSPI controller"
660	depends on ARCH_RENESAS || COMPILE_TEST
661	help
662	  SPI driver for SuperH HSPI blocks.
663
664config SPI_SIFIVE
665	tristate "SiFive SPI controller"
666	depends on HAS_IOMEM
667	help
668	  This exposes the SPI controller IP from SiFive.
669
670config SPI_SIRF
671	tristate "CSR SiRFprimaII SPI controller"
672	depends on SIRF_DMA
673	select SPI_BITBANG
674	help
675	  SPI driver for CSR SiRFprimaII SoCs
676
677config SPI_SLAVE_MT27XX
678	tristate "MediaTek SPI slave device"
679	depends on ARCH_MEDIATEK || COMPILE_TEST
680	depends on SPI_SLAVE
681	help
682	  This selects the MediaTek(R) SPI slave device driver.
683	  If you want to use MediaTek(R) SPI slave interface,
684	  say Y or M here.If you are not sure, say N.
685	  SPI slave drivers for Mediatek MT27XX series ARM SoCs.
686
687config SPI_SPRD
688	tristate "Spreadtrum SPI controller"
689	depends on ARCH_SPRD || COMPILE_TEST
690	help
691	  SPI driver for Spreadtrum SoCs.
692
693config SPI_SPRD_ADI
694	tristate "Spreadtrum ADI controller"
695	depends on ARCH_SPRD || COMPILE_TEST
696	depends on HWSPINLOCK || (COMPILE_TEST && !HWSPINLOCK)
697	help
698	  ADI driver based on SPI for Spreadtrum SoCs.
699
700config SPI_STM32
701	tristate "STMicroelectronics STM32 SPI controller"
702	depends on ARCH_STM32 || COMPILE_TEST
703	help
704	  SPI driver for STMicroelectronics STM32 SoCs.
705
706	  STM32 SPI controller supports DMA and PIO modes. When DMA
707	  is not available, the driver automatically falls back to
708	  PIO mode.
709
710config SPI_STM32_QSPI
711	tristate "STMicroelectronics STM32 QUAD SPI controller"
712	depends on ARCH_STM32 || COMPILE_TEST
713	depends on OF
714	help
715	  This enables support for the Quad SPI controller in master mode.
716	  This driver does not support generic SPI. The implementation only
717	  supports spi-mem interface.
718
719config SPI_ST_SSC4
720	tristate "STMicroelectronics SPI SSC-based driver"
721	depends on ARCH_STI || COMPILE_TEST
722	help
723	  STMicroelectronics SoCs support for SPI. If you say yes to
724	  this option, support will be included for the SSC driven SPI.
725
726config SPI_SUN4I
727	tristate "Allwinner A10 SoCs SPI controller"
728	depends on ARCH_SUNXI || COMPILE_TEST
729	help
730	  SPI driver for Allwinner sun4i, sun5i and sun7i SoCs
731
732config SPI_SUN6I
733	tristate "Allwinner A31 SPI controller"
734	depends on ARCH_SUNXI || COMPILE_TEST
735	depends on RESET_CONTROLLER
736	help
737	  This enables using the SPI controller on the Allwinner A31 SoCs.
738
739config SPI_SYNQUACER
740	tristate "Socionext's SynQuacer HighSpeed SPI controller"
741	depends on ARCH_SYNQUACER || COMPILE_TEST
742	help
743	  SPI driver for Socionext's High speed SPI controller which provides
744	  various operating modes for interfacing to serial peripheral devices
745	  that use the de-facto standard SPI protocol.
746
747	  It also supports the new dual-bit and quad-bit SPI protocol.
748
749config SPI_MXIC
750        tristate "Macronix MX25F0A SPI controller"
751        depends on SPI_MASTER
752        help
753          This selects the Macronix MX25F0A SPI controller driver.
754
755config SPI_MXS
756	tristate "Freescale MXS SPI controller"
757	depends on ARCH_MXS
758	select STMP_DEVICE
759	help
760	  SPI driver for Freescale MXS devices.
761
762config SPI_TEGRA114
763	tristate "NVIDIA Tegra114 SPI Controller"
764	depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
765	depends on RESET_CONTROLLER
766	help
767	  SPI driver for NVIDIA Tegra114 SPI Controller interface. This controller
768	  is different than the older SoCs SPI controller and also register interface
769	  get changed with this controller.
770
771config SPI_TEGRA20_SFLASH
772	tristate "Nvidia Tegra20 Serial flash Controller"
773	depends on ARCH_TEGRA || COMPILE_TEST
774	depends on RESET_CONTROLLER
775	help
776	  SPI driver for Nvidia Tegra20 Serial flash Controller interface.
777	  The main usecase of this controller is to use spi flash as boot
778	  device.
779
780config SPI_TEGRA20_SLINK
781	tristate "Nvidia Tegra20/Tegra30 SLINK Controller"
782	depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
783	depends on RESET_CONTROLLER
784	help
785	  SPI driver for Nvidia Tegra20/Tegra30 SLINK Controller interface.
786
787config SPI_THUNDERX
788	tristate "Cavium ThunderX SPI controller"
789	depends on PCI && 64BIT && (ARM64 || COMPILE_TEST)
790	help
791	  SPI host driver for the hardware found on Cavium ThunderX
792	  SOCs.
793
794config SPI_TOPCLIFF_PCH
795	tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) SPI"
796	depends on PCI && (X86_32 || MIPS || COMPILE_TEST)
797	help
798	  SPI driver for the Topcliff PCH (Platform Controller Hub) SPI bus
799	  used in some x86 embedded processors.
800
801	  This driver also supports the ML7213/ML7223/ML7831, a companion chip
802	  for the Atom E6xx series and compatible with the Intel EG20T PCH.
803
804config SPI_TXX9
805	tristate "Toshiba TXx9 SPI controller"
806	depends on GPIOLIB && (CPU_TX49XX || COMPILE_TEST)
807	help
808	  SPI driver for Toshiba TXx9 MIPS SoCs
809
810config SPI_UNIPHIER
811	tristate "Socionext UniPhier SPI Controller"
812	depends on (ARCH_UNIPHIER || COMPILE_TEST) && OF
813	help
814	  This enables a driver for the Socionext UniPhier SoC SCSSI SPI controller.
815
816	  UniPhier SoCs have SCSSI and MCSSI SPI controllers.
817	  Every UniPhier SoC has SCSSI which supports single channel.
818	  Older UniPhier Pro4/Pro5 also has MCSSI which support multiple channels.
819	  This driver supports SCSSI only.
820
821	  If your SoC supports SCSSI, say Y here.
822
823config SPI_XCOMM
824	tristate "Analog Devices AD-FMCOMMS1-EBZ SPI-I2C-bridge driver"
825	depends on I2C
826	help
827	  Support for the SPI-I2C bridge found on the Analog Devices
828	  AD-FMCOMMS1-EBZ board.
829
830config SPI_XILINX
831	tristate "Xilinx SPI controller common module"
832	depends on HAS_IOMEM
833	select SPI_BITBANG
834	help
835	  This exposes the SPI controller IP from the Xilinx EDK.
836
837	  See the "OPB Serial Peripheral Interface (SPI) (v1.00e)"
838	  Product Specification document (DS464) for hardware details.
839
840	  Or for the DS570, see "XPS Serial Peripheral Interface (SPI) (v2.00b)"
841
842config SPI_XLP
843	tristate "Netlogic XLP SPI controller driver"
844	depends on CPU_XLP || ARCH_THUNDER2 || COMPILE_TEST
845	help
846	  Enable support for the SPI controller on the Netlogic XLP SoCs.
847	  Currently supported XLP variants are XLP8XX, XLP3XX, XLP2XX, XLP9XX
848	  and XLP5XX.
849
850	  If you have a Netlogic XLP platform say Y here.
851	  If unsure, say N.
852
853config SPI_XTENSA_XTFPGA
854	tristate "Xtensa SPI controller for xtfpga"
855	depends on (XTENSA && XTENSA_PLATFORM_XTFPGA) || COMPILE_TEST
856	select SPI_BITBANG
857	help
858	  SPI driver for xtfpga SPI master controller.
859
860	  This simple SPI master controller is built into xtfpga bitstreams
861	  and is used to control daughterboard audio codec. It always transfers
862	  16 bit words in SPI mode 0, automatically asserting CS on transfer
863	  start and deasserting on end.
864
865config SPI_ZYNQ_QSPI
866	tristate "Xilinx Zynq QSPI controller"
867	depends on ARCH_ZYNQ || COMPILE_TEST
868	help
869	  This enables support for the Zynq Quad SPI controller
870	  in master mode.
871	  This controller only supports SPI memory interface.
872
873config SPI_ZYNQMP_GQSPI
874	tristate "Xilinx ZynqMP GQSPI controller"
875	depends on (SPI_MASTER && HAS_DMA) || COMPILE_TEST
876	help
877	  Enables Xilinx GQSPI controller driver for Zynq UltraScale+ MPSoC.
878
879#
880# Add new SPI master controllers in alphabetical order above this line
881#
882
883#
884# There are lots of SPI device types, with sensors and memory
885# being probably the most widely used ones.
886#
887comment "SPI Protocol Masters"
888
889config SPI_SPIDEV
890	tristate "User mode SPI device driver support"
891	help
892	  This supports user mode SPI protocol drivers.
893
894	  Note that this application programming interface is EXPERIMENTAL
895	  and hence SUBJECT TO CHANGE WITHOUT NOTICE while it stabilizes.
896
897config SPI_LOOPBACK_TEST
898	tristate "spi loopback test framework support"
899	depends on m
900	help
901	  This enables the SPI loopback testing framework driver
902
903	  primarily used for development of spi_master drivers
904	  and to detect regressions
905
906config SPI_TLE62X0
907	tristate "Infineon TLE62X0 (for power switching)"
908	depends on SYSFS
909	help
910	  SPI driver for Infineon TLE62X0 series line driver chips,
911	  such as the TLE6220, TLE6230 and TLE6240.  This provides a
912	  sysfs interface, with each line presented as a kind of GPIO
913	  exposing both switch control and diagnostic feedback.
914
915#
916# Add new SPI protocol masters in alphabetical order above this line
917#
918
919endif # SPI_MASTER
920
921#
922# SLAVE side ... listening to other SPI masters
923#
924
925config SPI_SLAVE
926	bool "SPI slave protocol handlers"
927	help
928	  If your system has a slave-capable SPI controller, you can enable
929	  slave protocol handlers.
930
931if SPI_SLAVE
932
933config SPI_SLAVE_TIME
934	tristate "SPI slave handler reporting boot up time"
935	help
936	  SPI slave handler responding with the time of reception of the last
937	  SPI message.
938
939config SPI_SLAVE_SYSTEM_CONTROL
940	tristate "SPI slave handler controlling system state"
941	help
942	  SPI slave handler to allow remote control of system reboot, power
943	  off, halt, and suspend.
944
945endif # SPI_SLAVE
946
947endif # SPI
948