Lines Matching +full:monitor +full:- +full:interval +full:- +full:ms
1 // SPDX-License-Identifier: GPL-2.0
124 #define XTAL 0xC000 /* b15-14: Crystal selection */
133 #define HSE 0x0080 /* b7: Hi-speed enable */
135 #define DRPD 0x0020 /* b5: D+/- pull down control */
140 #define OVCBIT 0x8000 /* b15-14: Over-current bit */
141 #define OVCMON 0xC000 /* b15-14: Over-current monitor */
142 #define SOFEA 0x0020 /* b5: SOF monitor */
143 #define IDMON 0x0004 /* b3: ID-pin monitor */
144 #define LNST 0x0003 /* b1-0: D+, D- line status */
146 #define FS_KSTS 0x0002 /* Full-Speed K State */
147 #define FS_JSTS 0x0001 /* Full-Speed J State */
148 #define LS_JSTS 0x0002 /* Low-Speed J State */
149 #define LS_KSTS 0x0001 /* Low-Speed K State */
160 #define RHST 0x0007 /* b1-0: Reset handshake status */
162 #define HSMODE 0x0003 /* Hi-Speed mode */
163 #define FSMODE 0x0002 /* Full-Speed mode */
164 #define LSMODE 0x0001 /* Low-Speed mode */
168 #define UTST 0x000F /* b3-0: Test select */
184 #define INTA 0x0001 /* b1: USB INT-pin active */
190 #define DFORM 0x0380 /* b9-7: DMA mode select */
212 #define CURPIPE 0x000F /* b2-0: PIPE select */
218 #define DTLN 0x0FFF /* b11-0: FIFO received data length */
231 #define OVRCRE 0x8000 /* b15: Over-current interrupt */
280 #define SOFMODE 0x000C /* b3-2: SOF pin select */
282 #define SOF_1MS 0x0004 /* SOF OUT 1ms Frame Signal */
295 #define DVSQ 0x0070 /* b6-4: Device state */
305 #define DVSQS 0x0030 /* b5-4: Device state */
307 #define CTSQ 0x0007 /* b2-0: Control transfer stage */
317 #define OVRCR 0x8000 /* b15: Over-current interrupt */
321 #define EOFERR 0x0040 /* b6: EOF-error interrupt */
328 #define FRNM 0x07FF /* b10-0: Frame number */
331 #define UFRNM 0x0007 /* b2-0: Micro frame number */
335 #define DEVSEL 0xF000 /* b15-14: Device address select */
336 #define MAXP 0x007F /* b6-0: Maxpacket size of default control pipe */
341 #define CSCLR 0x2000 /* b13: complete-split status clear */
342 #define CSSTS 0x1000 /* b12: complete-split status */
346 #define SQMON 0x0040 /* b6: Sequence toggle bit monitor */
350 #define PID 0x0003 /* b1-0: Response PID */
357 #define PIPENM 0x0007 /* b2-0: Pipe select */
360 #define R8A66597_TYP 0xC000 /* b15-14: Transfer type */
369 #define R8A66597_EPNUM 0x000F /* b3-0: Eendpoint number select */
372 #define BUFSIZE 0x7C00 /* b14-10: Pipe buffer size */
373 #define BUFNMB 0x007F /* b6-0: Pipe buffer number */
378 #define MXPS 0x07FF /* b10-0: Maxpacket size */
381 #define IFIS 0x1000 /* b12: Isochronous in-buffer flush mode select */
382 #define IITV 0x0007 /* b2-0: Isochronous interval */
386 #define INBUFM 0x4000 /* b14: IN buffer monitor (Only for PIPE1 to 5) */
387 #define CSCLR 0x2000 /* b13: complete-split status clear */
388 #define CSSTS 0x1000 /* b12: complete-split status */
393 #define SQMON 0x0040 /* b6: Sequence toggle bit monitor */
395 #define PID 0x0003 /* b1-0: Response PID */
402 #define TRNCNT 0xFFFF /* b15-0: Transaction counter */
434 #define LBA_WAIT 0x0030 /* b5-4: Local Bus Access Wait */