Lines Matching full:console
14 the console before standard serial driver is probed. The console is
33 bool "Support for console on AMBA serial port"
38 console (the system console is the device which receives all kernel
41 Even if you say Y here, the currently visible framebuffer console
42 (/dev/tty0) will still be used as the system console by default, but
44 "console=ttyAM0". (Try "man bootparam" or see the documentation of
60 bool "Support for console on AMBA serial port"
66 console (the system console is the device which receives all kernel
69 Even if you say Y here, the currently visible framebuffer console
70 (/dev/tty0) will still be used as the system console by default, but
72 "console=ttyAMA0". (Try "man bootparam" or see the documentation of
77 bool "Early console using Arm compatible semihosting"
83 Support for early debug console using Arm compatible semihosting.
84 This enables the console before standard serial driver is probed.
86 The console is enabled when early_param is processed.
89 bool "Early console using RISC-V SBI"
95 Support for early debug console using RISC-V SBI. This enables
96 the console before standard serial driver is probed. This is enabled
97 with "earlycon=sbi" on the kernel command line. The console is
116 bool "Support for console on a BCM1xxx DUART serial port"
122 system console (the system console is the device which receives all
140 bool "Support for console on AT91 serial port"
146 AT91 processor as the system console (the system
147 console is the device which receives all kernel messages and
178 /dev/, and pass "console=ttyATn" to the kernel.
183 bool "Serial console over KGDB NMI debugger port"
187 as a normal console (assuming that the port is attached to KGDB).
191 This is because this console driver processes the input in NMI
194 Note that since the console interprets input and uses polling
197 use raw console.
210 bool "Support for console on meson"
216 system console (the system console is the device which
230 bool "Support for console on CLPS711X serial port"
234 Even if you say Y here, the currently visible virtual console
235 (/dev/tty0) will still be used as the system console by default, but
237 "console=ttyCL1".
260 bool "Support for console on Samsung SoC serial port"
266 an virtual console.
268 Even if you say Y here, the currently visible virtual console
269 (/dev/tty0) will still be used as the system console by default, but
271 "console=ttySACx". (Try "man bootparam" or see the documentation of
297 bool "Support for console on a Tegra TCU serial port"
303 system console (the system console is the device which receives all
340 bool "Support console on DECstation DZ serial driver"
346 system console (the system console is the device which receives all
350 Note that the firmware uses ttyS3 as the serial console on
370 bool "Support for console on a DECstation Z85C30 serial port"
376 system console (the system console is the device which receives all
380 Note that the firmware uses ttyS1 as the serial console on the
395 bool "Console on DC21285 serial port"
400 make it the console by answering Y to this option.
402 Even if you say Y here, the currently visible virtual console
403 (/dev/tty0) will still be used as the system console by default, but
405 "console=ttyFB". (Try "man bootparam" or see the documentation of
427 bool "Console on PXA serial port (DEPRECATED)"
433 CPU you can make it the console by answering Y to this option.
435 Even if you say Y here, the currently visible virtual console
436 (/dev/tty0) will still be used as the system console by default, but
438 "console=ttySA0". (Try "man bootparam" or see the documentation of
457 bool "Console on SA1100 serial port"
462 CPU you can make it the console by answering Y to this option.
464 Even if you say Y here, the currently visible virtual console
465 (/dev/tty0) will still be used as the system console by default, but
467 "console=ttySA0". (Try "man bootparam" or see the documentation of
482 tristate "Console on IMX serial port"
487 CPU you can make it the console by answering Y/M to this option.
489 Even if you say Y/M here, the currently visible virtual console
490 (/dev/tty0) will still be used as the system console by default, but
492 "console=ttymxc0". (Try "man bootparam" or see the documentation of
518 bool "Support for console on Xilinx uartlite serial port"
524 console (the system console is the device which receives all kernel
551 bool "Console on Sun Zilog8530 serial port"
555 on your Sparc system as the console, you can do so by answering
567 bool "Console on Sun SU serial port"
571 on your Sparc system as the console, you can do so by answering
584 software console. The following steps need to be completed to use
590 root on this console.)
591 4. Change the kernel command console parameter to: console=ttyB0
594 bool "Support for console on serial MUX"
608 bool "Console on Sun Siemens SAB82532 serial port"
612 on your Sparc system as the console, you can do so by answering
616 bool "Sun4v Hypervisor Console support"
619 This driver supports the console device found on SUN4V Sparc
631 bool "Console on SGI Zilog8530 serial port"
651 bool "Support for console on SuperH SCI(F)" if EXPERT
657 bool "Support for early console on SuperH SCI(F)" if EXPERT
680 bool "Enable LPC32XX high speed UART serial console"
685 ports on the LPC32XX as the console, you can do so by answering
714 bool "Coldfire serial console support"
718 Enable a ColdFire internal serial port to be the system console.
755 bool "Console on Mac or PowerMac z85c30 serial port"
760 on your (Power)Mac as the console, you can do so by answering
772 bool "Support for console on CPM SCC/SMC serial port"
777 console (the system console is the device which receives all kernel
780 Even if you say Y here, the currently visible framebuffer console
781 (/dev/tty0) will still be used as the system console by default, but
783 "console=ttyCPM0". (Try "man bootparam" or see the documentation of
795 to use a serial port as a console, this must be included in kernel and
799 bool "PIC32 serial console support"
803 If you have a PIC32, this driver supports the putting a console on one
806 Say Y to use the PIC32 console, otherwise say N.
815 for use as console, it must be included in kernel and not as a
819 bool "Console on a Freescale MPC52xx/MPC512x family PSC serial port"
824 of the Freescale MPC52xx family as a console.
831 Select the MPC52xx console baud rate.
833 console baudrate
864 bool "TMPTX39XX/49XX SIO Console support"
894 bool "MSM serial console support"
906 bool "QCOM GENI Serial Console support"
911 Serial console driver for Qualcomm Technologies Inc's GENI based
920 bool "VIA VT8500 serial console support"
937 bool "Console on OMAP serial port"
942 console.
944 Even if you say Y here, the currently visible virtual console
945 (/dev/tty0) will still be used as the system console by default, but
947 "console=ttyOx". (Try "man bootparam" or see the documentation of
962 bool "Console on SiFive UART"
969 system console.
971 Even if you say Y here, the currently visible virtual console
972 (/dev/tty0) will still be used as the system console by default, but
974 "console=ttySIFx". (Try "man bootparam" or see the documentation of
988 bool "Console on Lantiq UART"
994 system console.
1014 bool "Console on SCCNXP serial port"
1018 Support for console on SCCNXP serial ports.
1076 BCM7xxx (STB) - DOCSIS console
1079 bool "Console on BCM63xx serial port"
1085 you can make it the console by answering Y to this option.
1095 bool "Console on GRLIB APBUART serial port"
1099 Support for running a console on the GRLIB APBUART
1108 bool "Altera JTAG UART console support"
1113 Enable a Altera JTAG UART port to be the system console.
1120 Bypass console output and keep going even if there is no
1148 bool "Altera UART console support"
1153 Enable a Altera UART port to be the system console.
1172 bool "Support for console on Intel EG20T PCH UART/OKI SEMICONDUCTOR ML7213 IOH"
1176 Say Y here if you wish to use the PCH UART as the system console
1177 (the system console is the device which receives all kernel messages and
1190 bool "MXS AUART console support"
1194 Enable a MXS AUART port to be the system console.
1205 bool "Cadence UART console support"
1210 Enable a Cadence UART port to be the system console.
1225 bool "Console on AR933X serial port"
1229 Enable a built-in UART port of the AR933X to be the system console.
1240 bool "MPS2 UART console support"
1260 bool "Console on ARC UART"
1265 Enable system Console on ARC UART
1308 bool "Console on Freescale lpuart serial port"
1314 you can make it the console by answering Y to this option.
1324 bool "Console on Freescale LINFlexD UART serial port"
1330 SoCs, you can make it the console by answering Y to this option.
1340 bool "Console on Conexant Digicolor serial port"
1345 SoCs, you can make it the console by answering Y to this option.
1360 bool "Support for console on ST ASC"
1383 bool "Spreadtrum UART console support"
1388 Support for early debug console using Spreadtrum's serial. This enables
1389 the console before standard serial driver is probed. This is enabled
1390 with "earlycon" on the kernel command line. The console is
1407 bool "Support for console on STM32"
1425 bool "Console on Marvell EBU serial port"
1431 Say 'Y' here if you wish to use Armada-3700 UART as the system console.
1432 (the system console is the device which receives all kernel messages
1446 bool "Console on Actions Semi Owl serial port"
1453 as the system console.
1465 bool "Console on RDA Micro serial port"
1472 console. Only earlycon is implemented currently.
1489 bool "Support for console on MILBEAUT USIO/UART serial port"
1496 SoCs as the system console (the system console is the device which
1522 bool "LiteUART serial port console support"
1528 controller from LiteX SoC builder as the system console
1529 (the system console is the device which receives all kernel messages
1546 bool "Console on Sunplus UART"
1552 system console.
1553 Even if you say Y here, the currently visible virtual console
1554 (/dev/tty0) will still be used as the system console by default, but
1556 "console=ttySUPx".
1565 for use as console, it must be included in kernel and not as a
1570 bool "Console on a Nuvotn MA35D1 family UART port"
1575 Nuvoton MA35D1 family as a console.
1576 Even if you say Y here, the currently visible virtual console
1577 (/dev/tty0) will still be used as the system console by default,
1579 "console=ttyNVTx".