Lines Matching +full:flash +full:- +full:leds
1 # SPDX-License-Identifier: GPL-2.0-only
13 LEDs from both userspace and optionally, by kernel events (triggers).
20 This option enables the LED sysfs class in /sys/class/leds. You'll
21 need this to do anything useful with LEDs. If unsure, say Y.
24 tristate "LED Flash Class Support"
27 This option enables the flash LED sysfs class in /sys/class/leds.
28 It wraps LED Class and adds flash LEDs specific sysfs attributes
30 for the flash related features of a LED device. It can be built
37 This option enables the multicolor LED sysfs class in /sys/class/leds.
40 for multicolor LEDs that are grouped together. This class is not
41 intended for single color LEDs. It can be built as a module.
48 for LED sysfs class devices under /sys/class/leds.
50 See Documentation/ABI/testing/sysfs-class-led for details.
59 This option enables support for on-chip LED drivers found on Marvell
66 This option enables support for the AN30259A 3-channel
70 will be called leds-an30259a.
77 This driver makes the PC Engines APU1 front panel LEDs
80 If you're looking for APU2/3, use the pcengines-apu2 driver.
84 module will be called leds-apu.
92 LEDs on Dell Wyse 3020 (Ariel) board via the KB3930 Embedded
104 an I2C interface, up to 36/54/72 LEDs or 12/18/24 RGBs,
108 will be called leds-aw200xx.
114 This option enables support for the AW2013 3-channel
118 will be called leds-aw2013.
126 This option enables support for LEDs connected to the BCM6328
135 This option enables support for LEDs connected to the BCM6358
143 This option enables support for charger and general purpose LEDs
147 will be called leds-cht-wcove.
155 This option enables support for LEDs offered by Motorola's
169 will be called leds-cr0014114.
182 will be called leds-el15203000.
191 This option enables basic support for the LEDs found on the front
192 side of CZ.NIC's Turris Omnia router. There are 12 RGB LEDs on the
221 This option enables support for the LEDs on National Semiconductor /
224 The LEDs can be controlled directly, through PWM input, or by the
225 ambient-light-sensor interface. The chip supports
226 hardware-accelerated blinking with maximum on and off periods of 9.8
234 This option enables support for LEDs connected to LM3642.
235 The LM3642 is a 4MHz fixed-frequency synchronous boost
236 converter plus 1.5A constant current driver for a high-current
252 This option enables support for the LEDs on Sharp Locomo.
253 Zaurus models SL-5500 and SL-5600.
268 This option enables support for on-chip LED drivers found on
280 tristate "LED Support for the WRAP series LEDs"
284 This option enables support for the PCEngines WRAP programmable LEDs.
298 This option enables support for the Cobalt Raq series LEDs.
307 LEDs on the I/O and CPU boards of SunFire UltraSPARC servers.
345 tristate "LED Support for GPIO connected LEDs"
349 This option enables support for the LEDs connected to GPIO
350 outputs. To be useful the particular board must have LEDs
351 and they must be connected to the GPIO lines. The LEDs must be
360 This option enables support for LEDs connected to the National
365 module will be called leds-lp3944.
374 This option enables support for LEDs connected to the Texas
378 module will be called leds-lp3952.
389 module will be called leds-lp50xx.
451 This option enables support for the Keyboard LEDs on the LP8788 PMIC.
460 This option enables support for the display cluster LEDs
470 programs through the LEDs subsystem. This LED has three
473 The driver supports two kinds of interface: using ledtrig-timer
474 or through /sys/class/leds/clevo::mail/brightness. As this LED
493 module will be called leds-clevo-mail.
500 This option enables support for LEDs connected to PCA955x
520 This option enables support for LEDs connected to the PCA963x
529 This option enables support for LEDs connected to PCA995x
534 tristate "LED support for status LEDs on WM831x PMICs"
538 This option enables support for the status LEDs of the WM831x
546 This option enables support for LEDs driven by the Wolfson
554 This option enables support for on-chip LED drivers found
558 tristate "Dialog DA9052/DA9053 LEDS"
562 This option enables support for on-chip LED drivers found
563 on Dialog Semiconductor DA9052-BC and DA9053-AA/Bx PMICs.
571 which can be used to control up to four LEDs.
578 This option enables support for pwm driven LEDs
585 This option enables support for regulator driven LEDs.
599 be called leds-bd2606mvv.
617 drive or power LEDs on the front panel. Using this driver
625 This option enables support for LEDs driven by a Linear Technology
626 LT3593 controller. This controller uses a special one-wire pulse
634 This option enables support for on-chip LED drivers found
638 be called leds-adp5520.
645 This option enables support for on-chip LED drivers found
649 tristate "LED support for Network Space v2 GPIO LEDs"
654 This option enables support for the dual-GPIO LEDs found on the
660 n090401 (Seagate NAS 4-Bay)
663 tristate "LED support for Big Network series LEDs"
669 This option enables support for LEDs found on the LaCie 2Big
670 and 5Big Network v2 boards. The LEDs are wired to a CPLD and are
677 This option enables support for LEDs connected to TC6507
679 Driver support brightness control and hardware-assisted blinking.
693 LEDs driver for MAX77650 family of PMICs from Maxim Integrated.
699 This option enables support for on-chip LED drivers on
707 This option enables support for LEDs connected to LM3554
708 and LM3556. It includes Torch, Flash and Indicator functions.
714 This option enables support for the LEDs on the Bachmann OT200.
715 Say Y to enable LEDs on the Bachmann OT200.
721 Say Y here to include support for the MEN 14F021P00 BMC LEDs.
724 will be called leds-menf21bmc.
731 This option enables support for LEDs connected to ISSI IS31FL319x
736 called leds-is31fl319x.
742 Say Y here to include support for ISSI IS31FL32XX and Si-En SN32xx
743 LED controllers. They are I2C devices with multiple constant-current
744 channels, each with independent 256-level PWM control.
752 LEDs.
755 called leds-sc27xx-bltc.
773 This option enables support for the system LEDs present on
776 will be called leds-powernv.
779 bool "LED support for LEDs on system controllers"
784 This option enables support for the LEDs on syscon type
801 This option enables support for the LEDs on the Mellanox
808 This option enables support for the LEDs on the Mellanox Ethernet and
811 module, choose 'M' here: the module will be called leds-mlxreg.
817 This option enables support for userspace LEDs. Say 'y' to enable this
826 This option enables support for the User1 and User2 LEDs on NI
830 will be called leds-nic78bx.
873 It is a single boost converter primarily for white LEDs and
881 This option enables support for the Red and White LEDs of
885 will be called leds-ip30.
894 source "drivers/leds/blink/Kconfig"
896 comment "Flash and Torch LED drivers"
897 source "drivers/leds/flash/Kconfig"
900 source "drivers/leds/rgb/Kconfig"
903 source "drivers/leds/trigger/Kconfig"
906 source "drivers/leds/simple/Kconfig"