Lines Matching full:default

15 /* Vendor ID Low byte, default value: 0x01 */
18 /* Vendor ID High byte, default value: 0x00 */
21 /* Device ID Low byte, default value: 0x60 */
24 /* Device ID High byte, default value: 0x86 */
27 /* Device Revision, default value: 0x10 */
30 /* OTP DBYTE510, default value: 0x00 */
33 /* System Control #1, default value: 0x00 */
44 /* System Control DPD, default value: 0x90 */
54 /* Dual link Control, default value: 0x00 */
65 /* PWD Software Reset, default value: 0x20 */
76 /* AKSV_1, default value: 0x00 */
79 /* Video H Resolution #1, default value: 0x00 */
82 /* Video Mode, default value: 0x00 */
86 /* Video Input Mode, default value: 0xc0 */
96 /* I2C Address reassignment, default value: 0x00 */
101 /* Fast Interrupt Status, default value: 0x00 */
122 /* GPIO Control, default value: 0x15 */
131 /* Interrupt Control, default value: 0x06 */
137 /* Interrupt State, default value: 0x00 */
141 /* Interrupt Source #1, default value: 0x00 */
144 /* Interrupt Source #2, default value: 0x00 */
147 /* Interrupt Source #3, default value: 0x01 */
151 /* Interrupt Source #5, default value: 0x00 */
154 /* Interrupt #1 Mask, default value: 0x00 */
157 /* Interrupt #2 Mask, default value: 0x00 */
160 /* Interrupt #3 Mask, default value: 0x00 */
163 /* Interrupt #5 Mask, default value: 0x00 */
167 /* Hot Plug Connection Control, default value: 0x45 */
178 /* GPIO Control, default value: 0x55 */
189 /* Interrupt Source 7, default value: 0x00 */
192 /* Interrupt Source 8, default value: 0x00 */
195 /* Interrupt #7 Mask, default value: 0x00 */
198 /* Interrupt #8 Mask, default value: 0x00 */
203 /* IEEE, default value: 0x10 */
207 /* TMDS Control #4, default value: 0x02 */
212 /* BIST CNTL, default value: 0x00 */
223 /* BIST DURATION0, default value: 0x00 */
227 /* BIST VIDEO_MODE, default value: 0x00 */
231 /* BIST DURATION0, default value: 0x00 */
234 /* BIST DURATION1, default value: 0x00 */
237 /* BIST DURATION2, default value: 0x00 */
240 /* BIST 8BIT_PATTERN, default value: 0x00 */
243 /* LM DDC, default value: 0x80 */
252 /* DDC I2C Manual, default value: 0x03 */
263 /* DDC I2C Target Slave Address, default value: 0x00 */
267 /* DDC I2C Target Segment Address, default value: 0x00 */
270 /* DDC I2C Target Offset Address, default value: 0x00 */
273 /* DDC I2C Data In count #1, default value: 0x00 */
276 /* DDC I2C Data In count #2, default value: 0x00 */
280 /* DDC I2C Status, default value: 0x04 */
290 /* DDC I2C Command, default value: 0x70 */
301 /* DDC I2C FIFO Data In/Out, default value: 0x00 */
304 /* DDC I2C Data Out Counter, default value: 0x00 */
309 /* DDC I2C Delay Count, default value: 0x14 */
312 /* Test Control, default value: 0x80 */
320 /* CBUS Address, default value: 0x00 */
329 /* USBT CTRL0, default value: 0x00 */
338 /* HSIC RX Control3, default value: 0x07 */
349 /* TDM TX NUMBITS, default value: 0x0c */
355 /* TDM TX NUMSPISYM, default value: 0x04 */
358 /* TDM TX NUMHSICSYM, default value: 0x14 */
361 /* TDM TX NUMTOTSYM, default value: 0x18 */
364 /* TDM TX INT Low, default value: 0x00 */
375 /* TDM TX INT High, default value: 0x00 */
386 /* TDM RX Control, default value: 0x1c */
392 /* TDM RX NUMSPISYM, default value: 0x04 */
395 /* TDM RX NUMHSICSYM, default value: 0x14 */
398 /* TDM RX NUMTOTSYM, default value: 0x18 */
401 /* TDM RX Status 2nd, default value: 0x00 */
406 /* TDM RX INT Low, default value: 0x00 */
409 /* TDM RX INT High, default value: 0x00 */
414 /* TDM RX INTMASK High, default value: 0x00 */
417 /* HSIC TX CRTL, default value: 0x00 */
425 /* HSIC TX INT Low, default value: 0x00 */
428 /* HSIC TX INT High, default value: 0x00 */
431 /* HSIC Keeper, default value: 0x00 */
437 /* HSIC Flow Control General, default value: 0x02 */
442 /* HSIC Flow Control CTR13, default value: 0xfc */
445 /* HSIC Flow Control CTR14, default value: 0xff */
448 /* HSIC Flow Control CTR15, default value: 0xff */
451 /* HSIC Flow Control CTR50, default value: 0x03 */
454 /* HSIC Flow Control INTR0, default value: 0x00 */
464 /* TDM Low Latency, default value: 0x20 */
472 /* TMDS 0 Clock Control, default value: 0x10 */
477 /* TMDS Clock Enable, default value: 0x00 */
481 /* TMDS Channel Enable, default value: 0x00 */
486 /* BGR_BIAS, default value: 0x07 */
491 /* TMDS 0 Digital I2C BW, default value: 0x0a */
494 /* TMDS 0 Digital Zone Control, default value: 0xe0 */
501 /* TMDS 0 Digital PLL Mode Control, default value: 0x00 */
506 /* MHL Tx Control 6th, default value: 0xa0 */
511 /* Packet Filter0, default value: 0x00 */
522 /* Packet Filter1, default value: 0x00 */
531 /* TMDS Clock Status, default value: 0x10 */
541 /* RX_HDMI Control, default value: 0x10 */
550 /* RX_HDMI Control, default value: 0x38 */
557 /* RX_HDMI Control, default value: 0x0f */
561 /* rx_hdmi Clear Buffer, default value: 0x00 */
571 /* RX_HDMI VSI Header1, default value: 0x00 */
574 /* RX_HDMI VSI MHL Monitor, default value: 0x3c */
580 /* Interrupt Source 9, default value: 0x00 */
586 /* Interrupt 9 Mask, default value: 0x00 */
589 /* TPI CBUS Start, default value: 0x00 */
600 /* EDID Control, default value: 0x10 */
611 /* EDID FIFO Addr, default value: 0x00 */
614 /* EDID FIFO Write Data, default value: 0x00 */
617 /* EDID/DEVCAP FIFO Internal Addr, default value: 0x00 */
620 /* EDID FIFO Read Data, default value: 0x00 */
623 /* EDID DDC Segment Pointer, default value: 0x00 */
626 /* TX IP BIST CNTL and Status, default value: 0x00 */
636 /* TX IP BIST INST LOW, default value: 0x00 */
640 /* TX IP BIST PATTERN LOW, default value: 0x00 */
644 /* TX IP BIST CONFIGURE LOW, default value: 0x00 */
648 /* E-MSC General Control, default value: 0x80 */
659 /* E-MSC Comma ErrorCNT, default value: 0x03 */
664 /* E-MSC RFIFO ByteCnt, default value: 0x00 */
668 /* SPI Burst Cnt Status, default value: 0x00 */
671 /* SPI Burst Status and SWRST, default value: 0x00 */
678 /* E-MSC 1st Interrupt, default value: 0x00 */
689 /* E-MSC Interrupt Mask, default value: 0x00 */
692 /* I2C E-MSC XMIT FIFO Write Port, default value: 0x00 */
695 /* I2C E-MSC RCV FIFO Write Port, default value: 0x00 */
698 /* E-MSC 2nd Interrupt, default value: 0x00 */
702 /* E-MSC Interrupt Mask, default value: 0x00 */
706 /* MHL Top Ctl, default value: 0x00 */
712 /* MHL DataPath 1st Ctl, default value: 0xbc */
718 /* MHL DataPath 2nd Ctl, default value: 0xbb */
723 /* MHL DataPath 3rd Ctl, default value: 0x2f */
730 /* MHL DataPath 4th Ctl, default value: 0x48 */
735 /* MHL DataPath 5th Ctl, default value: 0x48 */
740 /* MHL DataPath 6th Ctl, default value: 0x3f */
748 /* MHL PLL 1st Ctl, default value: 0x05 */
771 /* MHL PLL 3rd Ctl, default value: 0x80 */
778 /* MHL CBUS 1st Ctl, default value: 0x12 */
796 /* MHL CBUS 2nd Ctl, default value: 0x03 */
803 /* MHL CoC 1st Ctl, default value: 0xc3 */
809 /* MHL CoC 2nd Ctl, default value: 0x87 */
814 /* MHL CoC 4th Ctl, default value: 0x00 */
818 /* MHL CoC 5th Ctl, default value: 0x28 */
823 /* MHL CoC 6th Ctl, default value: 0x0d */
826 /* MHL DoC 1st Ctl, default value: 0x18 */
833 /* MHL DataPath 7th Ctl, default value: 0x2a */
842 /* MHL DataPath 8th Ctl, default value: 0x06 */
849 /* Tx Zone Ctl1, default value: 0x00 */
853 /* MHL3 Tx Zone Ctl, default value: 0x00 */
863 /* HDCP Polling Control and Status, default value: 0x70 */
873 /* HDCP Interrupt 0, default value: 0x00 */
876 /* HDCP Interrupt 0 Mask, default value: 0x00 */
879 /* HDCP General Control 0, default value: 0x02 */
890 /* HDCP General Control 1, default value: 0x08 */
898 /* HDCP Misc Control, default value: 0x00 */
906 /* HDCP RPT SMNG K, default value: 0x00 */
909 /* HDCP RPT SMNG In, default value: 0x00 */
912 /* HDCP Auth Status, default value: 0x00 */
915 /* HDCP RPT RCVID Out, default value: 0x00 */
918 /* HDCP TP1, default value: 0x62 */
921 /* HDCP GP Out 0, default value: 0x00 */
924 /* HDCP Repeater RCVR ID 0, default value: 0x00 */
927 /* HDCP DDCM Status, default value: 0x00 */
932 /* HDMI2MHL3 Control, default value: 0x0a */
947 /* HDMI2MHL3 Port0 Control, default value: 0x04 */
959 /* HDMI2MHL3 Scramble Control, default value: 0x41 */
964 /* HSIC Div Ctl, default value: 0x05 */
969 /* MHL Capability 1st Byte, default value: 0x00 */
972 /* MHL Interrupt 1st Byte, default value: 0x00 */
975 /* Device Status 1st byte, default value: 0x00 */
978 /* CBUS Scratch Pad 1st Byte, default value: 0x00 */
981 /* MHL Extended Capability 1st Byte, default value: 0x00 */
984 /* Device Extended Status 1st byte, default value: 0x00 */
987 /* TPI DTD Byte2, default value: 0x00 */
999 /* Input Format, default value: 0x00 */
1006 /* Output Format, default value: 0x00 */
1012 /* TPI AVI Check Sum, default value: 0x00 */
1015 /* TPI System Control, default value: 0x00 */
1026 /* TPI COPP Query Data, default value: 0x00 */
1040 /* TPI COPP Control Data, default value: 0x00 */
1049 /* TPI Interrupt Enable, default value: 0x00 */
1052 /* TPI Interrupt Status Low Byte, default value: 0x00 */
1062 /* TPI DS BCAPS Status, default value: 0x00 */
1065 /* TPI BStatus1, default value: 0x00 */
1070 /* TPI BStatus2, default value: 0x10 */
1077 /* TPI HW Optimization Control #3, default value: 0x00 */
1084 /* TPI Info Frame Select, default value: 0x00 */
1098 /* TPI Info Byte #0, default value: 0x00 */
1101 /* CoC Status, default value: 0x00 */
1112 /* CoC 1st Ctl, default value: 0x40 */
1115 /* CoC 2nd Ctl, default value: 0x0a */
1120 /* CoC 3rd Ctl, default value: 0x14 */
1125 /* CoC 4th Ctl, default value: 0x40 */
1130 /* CoC 7th Ctl, default value: 0x00 */
1136 /* CoC 8th Ctl, default value: 0x06 */
1144 /* CoC 10th Ctl, default value: 0x00 */
1147 /* CoC 11th Ctl, default value: 0x00 */
1150 /* CoC 12th Ctl, default value: 0x00 */
1153 /* CoC 13th Ctl, default value: 0x0f */
1156 /* CoC 14th Ctl, default value: 0x0a */
1161 /* CoC 15th Ctl, default value: 0x0a */
1166 /* CoC 16th Ctl, default value: 0x00 */
1171 /* CoC 18th Ctl, default value: 0x32 */
1176 /* CoC 21st Ctl, default value: 0x00 */
1181 /* CoC 22nd Ctl, default value: 0x00 */
1187 /* CoC Interrupt, default value: 0x00 */
1190 /* CoC Interrupt Mask, default value: 0x00 */
1195 /* CoC Misc Ctl, default value: 0x00 */
1199 /* CoC 24th Ctl, default value: 0x00 */
1204 /* CoC 25th Ctl, default value: 0x00 */
1209 /* CoC 26th Ctl, default value: 0x00 */
1214 /* CoC 27th Ctl, default value: 0x00 */
1219 /* DoC 9th Status, default value: 0x00 */
1222 /* DoC 10th Status, default value: 0x00 */
1225 /* DoC 5th CFG, default value: 0x00 */
1229 /* DoC 1st Ctl, default value: 0x40 */
1232 /* DoC 7th Ctl, default value: 0x00 */
1239 /* DoC 8th Ctl, default value: 0x00 */
1247 /* DoC 9th Ctl, default value: 0x00 */
1254 /* DoC 10th Ctl, default value: 0x00 */
1257 /* DoC 11th Ctl, default value: 0x00 */
1260 /* DoC 15th Ctl, default value: 0x00 */
1267 /* Interrupt Mask 1st, default value: 0x00 */
1270 /* Interrupt Mask 2nd, default value: 0x00 */
1273 /* Interrupt Mask 3rd, default value: 0x00 */
1276 /* Interrupt Mask 4th, default value: 0x00 */
1279 /* MDT Receive Time Out, default value: 0x00 */
1282 /* MDT Transmit Time Out, default value: 0x00 */
1285 /* MDT Receive Control, default value: 0x00 */
1295 /* MDT Receive Read Port, default value: 0x00 */
1298 /* MDT Transmit Control, default value: 0x70 */
1309 /* MDT Receive WRITE Port, default value: 0x00 */
1312 /* MDT RFIFO Status, default value: 0x00 */
1317 /* MDT XFIFO Status, default value: 0x80 */
1323 /* MDT Interrupt 0, default value: 0x0c */
1329 /* MDT Interrupt 0 Mask, default value: 0x00 */
1332 /* MDT Interrupt 1, default value: 0x00 */
1341 /* MDT Interrupt 1 Mask, default value: 0x00 */
1344 /* CBUS Vendor ID, default value: 0x01 */
1347 /* CBUS Connection Status, default value: 0x00 */
1355 /* CBUS Interrupt 1st, default value: 0x00 */
1366 /* CBUS Interrupt Mask 1st, default value: 0x00 */
1369 /* CBUS Interrupt 2nd, default value: 0x00 */
1376 /* CBUS Interrupt Mask 2nd, default value: 0x00 */
1379 /* CBUS DDC Abort Interrupt, default value: 0x00 */
1382 /* CBUS DDC Abort Interrupt Mask, default value: 0x00 */
1385 /* CBUS MSC Requester Abort Interrupt, default value: 0x00 */
1388 /* CBUS MSC Requester Abort Interrupt Mask, default value: 0x00 */
1391 /* CBUS MSC Responder Abort Interrupt, default value: 0x00 */
1394 /* CBUS MSC Responder Abort Interrupt Mask, default value: 0x00 */
1397 /* CBUS RX DISCOVERY interrupt, default value: 0x00 */
1400 /* CBUS RX DISCOVERY Interrupt Mask, default value: 0x00 */
1403 /* CBUS_Link_Layer Control #8, default value: 0x00 */
1406 /* MDT State Machine Status, default value: 0x00 */
1411 /* CBUS MSC command trigger, default value: 0x00 */
1420 /* CBUS MSC Command/Offset, default value: 0x00 */
1435 /* CBUS MSC Heartbeat Control, default value: 0x27 */
1441 /* CBUS MSC Compatibility Control, default value: 0x02 */
1449 /* CBUS3 Converter Control, default value: 0x24 */
1456 /* Discovery Control1, default value: 0x24 */
1468 /* Discovery Control4, default value: 0x80 */
1474 /* Discovery Control5, default value: 0x03 */
1479 /* Discovery Control8, default value: 0x81 */
1484 /* Discovery Control9, default value: 0x54 */
1494 /* Discovery Status1, default value: 0x00 */
1499 /* Discovery Status2, default value: 0x00 */
1517 /* Interrupt CBUS_reg1 INTR0, default value: 0x00 */
1529 /* Interrupt CBUS_reg1 INTR0 Mask, default value: 0x00 */