Lines Matching +full:hi +full:- +full:z
1 // SPDX-License-Identifier: GPL-2.0-only
3 * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
5 /dts-v1/;
8 #include <dt-bindings/interrupt-controller/irq.h>
12 compatible = "ti,am335x-evm", "ti,am33xx";
16 cpu0-supply = <&vdd1_reg>;
26 stdout-path = &uart0;
30 compatible = "regulator-fixed";
31 regulator-name = "vbat";
32 regulator-min-microvolt = <5000000>;
33 regulator-max-microvolt = <5000000>;
34 regulator-boot-on;
38 compatible = "regulator-fixed";
39 regulator-name = "lis3_reg";
40 regulator-boot-on;
44 compatible = "regulator-fixed";
45 regulator-name = "wlan-en-regulator";
46 regulator-min-microvolt = <1800000>;
47 regulator-max-microvolt = <1800000>;
49 /* WLAN_EN GPIO for this board - Bank1, pin16 */
53 startup-delay-us = <70000>;
54 enable-active-high;
58 v1_8d_reg: fixedregulator-v1_8d {
59 compatible = "regulator-fixed";
60 regulator-name = "v1_8d";
61 vin-supply = <&vbat>;
62 regulator-min-microvolt = <1800000>;
63 regulator-max-microvolt = <1800000>;
67 v3_3d_reg: fixedregulator-v3_3d {
68 compatible = "regulator-fixed";
69 regulator-name = "v3_3d";
70 vin-supply = <&vbat>;
71 regulator-min-microvolt = <3300000>;
72 regulator-max-microvolt = <3300000>;
76 compatible = "gpio-matrix-keypad";
77 debounce-delay-ms = <5>;
78 col-scan-delay-us = <2>;
80 row-gpios = <&gpio1 25 GPIO_ACTIVE_HIGH /* Bank1, pin25 */
84 col-gpios = <&gpio1 21 GPIO_ACTIVE_HIGH /* Bank1, pin21 */
95 gpio_keys: volume-keys {
96 compatible = "gpio-keys";
99 switch-9 {
100 label = "volume-up";
103 wakeup-source;
106 switch-10 {
107 label = "volume-down";
110 wakeup-source;
115 compatible = "pwm-backlight";
117 brightness-levels = <0 51 53 56 62 75 101 152 255>;
118 default-brightness-level = <8>;
122 compatible = "tfc,s9700rtwv43tr-01b";
124 pinctrl-names = "default";
125 pinctrl-0 = <&lcd_pins_s0>;
130 remote-endpoint = <&lcdc_0>;
136 compatible = "simple-audio-card";
137 simple-audio-card,name = "AM335x-EVM";
138 simple-audio-card,widgets =
141 simple-audio-card,routing =
146 simple-audio-card,format = "dsp_b";
147 simple-audio-card,bitclock-master = <&sound_master>;
148 simple-audio-card,frame-master = <&sound_master>;
149 simple-audio-card,bitclock-inversion;
151 simple-audio-card,cpu {
152 sound-dai = <&mcasp1>;
155 sound_master: simple-audio-card,codec {
156 sound-dai = <&tlv320aic3106>;
157 system-clock-frequency = <12000000>;
163 pinctrl-names = "default";
164 pinctrl-0 = <&matrix_keypad_s0 &volume_keys_s0 &clkout2_pin>;
166 matrix_keypad_s0: matrix-keypad-s0-pins {
167 pinctrl-single,pins = <
176 volume_keys_s0: volume-keys-s0-pins {
177 pinctrl-single,pins = <
183 i2c0_pins: i2c0-pins {
184 pinctrl-single,pins = <
190 i2c1_pins: i2c1-pins {
191 pinctrl-single,pins = <
197 uart0_pins: uart0-pins {
198 pinctrl-single,pins = <
204 uart1_pins: uart1-pins {
205 pinctrl-single,pins = <
213 clkout2_pin: clkout2-pins {
214 pinctrl-single,pins = <
219 nandflash_pins_s0: nandflash-s0-pins {
220 pinctrl-single,pins = <
239 ecap0_pins: backlight-pins {
240 pinctrl-single,pins = <
245 cpsw_default: cpsw-default-pins {
246 pinctrl-single,pins = <
263 cpsw_sleep: cpsw-sleep-pins {
264 pinctrl-single,pins = <
281 davinci_mdio_default: davinci-mdio-default-pins {
282 pinctrl-single,pins = <
289 davinci_mdio_sleep: davinci-mdio-sleep-pins {
290 pinctrl-single,pins = <
297 mmc1_pins: mmc1-pins {
298 pinctrl-single,pins = <
310 mmc3_pins: mmc3-pins {
311 pinctrl-single,pins = <
321 wlan_pins: wlan-pins {
322 pinctrl-single,pins = <
329 lcd_pins_s0: lcd-s0-pins {
330 pinctrl-single,pins = <
362 mcasp1_pins: mcasp1-pins {
363 pinctrl-single,pins = <
371 mcasp1_pins_sleep: mcasp1-sleep-pins {
372 pinctrl-single,pins = <
380 dcan1_pins_default: dcan1-default-pins {
381 pinctrl-single,pins = <
389 pinctrl-names = "default";
390 pinctrl-0 = <&uart0_pins>;
396 pinctrl-names = "default";
397 pinctrl-0 = <&uart1_pins>;
403 pinctrl-names = "default";
404 pinctrl-0 = <&i2c0_pins>;
407 clock-frequency = <400000>;
419 pinctrl-names = "default";
420 pinctrl-0 = <&i2c1_pins>;
423 clock-frequency = <100000>;
428 Vdd-supply = <&lis3_reg>;
429 Vdd_IO-supply = <&lis3_reg>;
431 st,click-single-x;
432 st,click-single-y;
433 st,click-single-z;
434 st,click-thresh-x = <10>;
435 st,click-thresh-y = <10>;
436 st,click-thresh-z = <10>;
437 st,irq1-click;
438 st,irq2-click;
439 st,wakeup-x-lo;
440 st,wakeup-x-hi;
441 st,wakeup-y-lo;
442 st,wakeup-y-hi;
443 st,wakeup-z-lo;
444 st,wakeup-z-hi;
445 st,min-limit-x = <120>;
446 st,min-limit-y = <120>;
447 st,min-limit-z = <140>;
448 st,max-limit-x = <550>;
449 st,max-limit-y = <550>;
450 st,max-limit-z = <750>;
464 #sound-dai-cells = <0>;
470 AVDD-supply = <&v3_3d_reg>;
471 IOVDD-supply = <&v3_3d_reg>;
472 DRVDD-supply = <&v3_3d_reg>;
473 DVDD-supply = <&v1_8d_reg>;
480 blue-and-red-wiring = "crossed";
484 remote-endpoint = <&panel_0>;
498 pinctrl-names = "default";
499 pinctrl-0 = <&ecap0_pins>;
505 pinctrl-names = "default";
506 pinctrl-0 = <&nandflash_pins_s0>;
509 compatible = "ti,omap2-nand";
511 interrupt-parent = <&gpmc>;
514 rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
515 ti,nand-xfer-type = "prefetch-dma";
516 ti,nand-ecc-opt = "bch8";
517 ti,elm-id = <&elm>;
518 nand-bus-width = <8>;
519 gpmc,device-width = <1>;
520 gpmc,sync-clk-ps = <0>;
521 gpmc,cs-on-ns = <0>;
522 gpmc,cs-rd-off-ns = <44>;
523 gpmc,cs-wr-off-ns = <44>;
524 gpmc,adv-on-ns = <6>;
525 gpmc,adv-rd-off-ns = <34>;
526 gpmc,adv-wr-off-ns = <44>;
527 gpmc,we-on-ns = <0>;
528 gpmc,we-off-ns = <40>;
529 gpmc,oe-on-ns = <0>;
530 gpmc,oe-off-ns = <54>;
531 gpmc,access-ns = <64>;
532 gpmc,rd-cycle-ns = <82>;
533 gpmc,wr-cycle-ns = <82>;
534 gpmc,bus-turnaround-ns = <0>;
535 gpmc,cycle2cycle-delay-ns = <0>;
536 gpmc,clk-activation-ns = <0>;
537 gpmc,wr-access-ns = <40>;
538 gpmc,wr-data-mux-bus-ns = <0>;
540 /* All SPL-* partitions are sized to minimal length
542 * NAND flash this is equal to size of erase-block */
543 #address-cells = <1>;
544 #size-cells = <1>;
562 label = "NAND.u-boot-spl-os";
566 label = "NAND.u-boot";
570 label = "NAND.u-boot-env";
574 label = "NAND.u-boot-env.backup1";
582 label = "NAND.file-system";
591 #sound-dai-cells = <0>;
592 pinctrl-names = "default", "sleep";
593 pinctrl-0 = <&mcasp1_pins>;
594 pinctrl-1 = <&mcasp1_pins_sleep>;
598 op-mode = <0>; /* MCASP_IIS_MODE */
599 tdm-slots = <2>;
601 serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
604 tx-num-evt = <32>;
605 rx-num-evt = <32>;
609 vcc1-supply = <&vbat>;
610 vcc2-supply = <&vbat>;
611 vcc3-supply = <&vbat>;
612 vcc4-supply = <&vbat>;
613 vcc5-supply = <&vbat>;
614 vcc6-supply = <&vbat>;
615 vcc7-supply = <&vbat>;
616 vccio-supply = <&vbat>;
620 regulator-always-on;
624 regulator-always-on;
628 /* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
629 regulator-name = "vdd_mpu";
630 regulator-min-microvolt = <912500>;
631 regulator-max-microvolt = <1351500>;
632 regulator-boot-on;
633 regulator-always-on;
637 /* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
638 regulator-name = "vdd_core";
639 regulator-min-microvolt = <912500>;
640 regulator-max-microvolt = <1150000>;
641 regulator-boot-on;
642 regulator-always-on;
646 regulator-always-on;
650 regulator-always-on;
654 regulator-always-on;
658 regulator-always-on;
662 regulator-always-on;
666 regulator-always-on;
670 regulator-always-on;
674 regulator-always-on;
678 regulator-min-microvolt = <1800000>;
679 regulator-max-microvolt = <3300000>;
680 regulator-always-on;
686 pinctrl-names = "default", "sleep";
687 pinctrl-0 = <&cpsw_default>;
688 pinctrl-1 = <&cpsw_sleep>;
693 pinctrl-names = "default", "sleep";
694 pinctrl-0 = <&davinci_mdio_default>;
695 pinctrl-1 = <&davinci_mdio_sleep>;
697 ethphy0: ethernet-phy@0 {
703 phy-handle = <ðphy0>;
704 phy-mode = "rgmii-id";
705 ti,dual-emac-pvid = <1>;
716 ti,x-plate-resistance = <200>;
717 ti,coordinate-readouts = <5>;
718 ti,wire-config = <0x00 0x11 0x22 0x33>;
719 ti,charge-delay = <0x400>;
723 ti,adc-channels = <4 5 6 7>;
729 vmmc-supply = <&vmmc_reg>;
730 bus-width = <4>;
731 pinctrl-names = "default";
732 pinctrl-0 = <&mmc1_pins>;
733 cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
738 xbar-event-map element */
741 dma-names = "tx", "rx";
743 vmmc-supply = <&wlan_en_reg>;
744 bus-width = <4>;
745 pinctrl-names = "default";
746 pinctrl-0 = <&mmc3_pins &wlan_pins>;
747 non-removable;
748 cap-power-off-card;
749 keep-power-in-suspend;
751 #address-cells = <1>;
752 #size-cells = <0>;
756 interrupt-parent = <&gpio3>;
771 pinctrl-names = "default";
772 pinctrl-0 = <&dcan1_pins_default>;
777 clock-names = "ext-clk", "int-clk";
785 firmware-name = "am335x-evm-scale-data.bin";