Lines Matching +full:7 +full:b
23 * <15> :: VDM type ( 1b == structured, 0b == unstructured )
26 * <10:8> :: object position (1-7 valid ... used for enter/exit mode only)
27 * <7:6> :: command type (SVDM only?)
69 #define VDO_CMD_FLASH_WRITE VDO_CMD_VENDOR(7)
110 * <26> :: modal operation supported (1b == yes)
177 * <23:22> :: Connector type (10b == receptacle, 11b == captive plug)
180 * <7> :: Vconn required (AMA only, 0b == no, 1b == yes)
181 * <6> :: Vbus required (AMA only, 0b == yes, 1b == no)
231 | ((vcpwr) & 0x7) << 8 | (vcr) << 7 | (vbr) << 6 | ((alt) & 0x7) << 3 \
240 * <23:22> :: Connector type (10b == receptacle, 11b == captive plug)
263 * <19:18> :: type-C to Type-A/B/C/Captive (00b == A, 01 == B, 10 == C, 11 == Captive)
266 * <12:11> :: cable termination type (11b == both ends active VCONN req)
267 * <10> :: SSTX1 Directionality support (0b == fixed, 1b == cfgable)
270 * <7> :: SSRX2 Directionality support
271 * <6:5> :: Vbus current handling capability (01b == 3A, 10b == 5A)
272 * <4> :: Vbus through cable (0b == no, 1b == yes)
273 * <3> :: SOP" controller present? (0b == no, 1b == yes)
282 * <19:18> :: Type-C to Type-C/Captive (10b == C, 11b == Captive)
285 * <12:11> :: cable termination type (10b == Vconn not req, 01b == Vconn req)
286 * <10:9> :: Maximum Vbus voltage (00b == 20V, 01b == 30V, 10b == 40V, 11b == 50V)
287 * <8:7> :: Reserved, Shall be set to zero
288 * <6:5> :: Vbus current handling capability (01b == 3A, 10b == 5A)
298 * <19:18> :: Connector type (10b == C, 11b == Captive)
301 * <12:11> :: cable termination type (10b == one end active, 11b == both ends active VCONN req)
302 * <10:9> :: Maximum Vbus voltage (00b == 20V, 01b == 30V, 10b == 40V, 11b == 50V)
303 * <8> :: SBU supported (0b == supported, 1b == not supported)
304 * <7> :: SBU type (0b == passive, 1b == active)
305 * <6:5> :: Vbus current handling capability (01b == 3A, 10b == 5A)
306 * <4> :: Vbus through cable (0b == no, 1b == yes)
307 * <3> :: SOP" controller present? (0b == no, 1b == yes)
327 #define CABLE_LATENCY_7M 7
367 | (tx2d) << 9 | (rx1d) << 8 | (rx2d) << 7 | ((cur) & 0x3) << 5 \
376 | ((vbm) & 0x3) << 9 | (sbu) << 8 | (sbut) << 7 | ((cur) & 0x3) << 5 \
388 * <11> :: U3 to U0 transition mode (0b == direct, 1b == through U3S)
389 * <10> :: Physical connection (0b == copper, 1b == optical)
390 * <9> :: Active element (0b == redriver, 1b == retimer)
391 * <8> :: USB4 supported (0b == yes, 1b == no)
392 * <7:6> :: USB2 hub hops consumed
393 * <5> :: USB2 supported (0b == yes, 1b == no)
394 * <4> :: USB3.2 supported (0b == yes, 1b == no)
395 * <3> :: USB lanes supported (0b == one lane, 1b == two lanes)
396 * <2> :: Optically isolated active cable (0b == no, 1b == yes)
398 * <0> :: USB gen (0b == gen1, 1b == gen2+)
441 * <11> :: SSTX1 Directionality support (0b == fixed, 1b == cfgable)
445 * <7:5> :: Vconn power
471 * <16:15> :: Maximum Vbus voltage (00b == 20V, 01b == 30V, 10b == 40V, 11b == 50V)
472 * <14> :: Charge through current support (0b == 3A, 1b == 5A)
474 * <12:7> :: Vbus impedance
476 * <0> :: Charge through support (0b == no, 1b == yes)
490 | ((vbm) & 0x3) << 15 | (curr) << 14 | ((vbi) & 0x3f) << 7 \