Lines Matching +full:chip +full:- +full:select
1 # SPDX-License-Identifier: GPL-2.0
19 comment "Non-8250 serial port support"
24 select SERIAL_CORE
35 select SERIAL_CORE_CONSOLE
51 select SERIAL_CORE
62 select SERIAL_CORE_CONSOLE
63 select SERIAL_EARLYCON
79 select SERIAL_CORE
80 select SERIAL_CORE_CONSOLE
81 select SERIAL_EARLYCON
89 bool "Early console using RISC-V SBI"
91 select SERIAL_CORE
92 select SERIAL_CORE_CONSOLE
93 select SERIAL_EARLYCON
95 Support for early debug console using RISC-V SBI. This enables
101 tristate "BCM1xxx on-chip DUART serial support"
103 select SERIAL_CORE
107 the BCM1250 and derived System-On-a-Chip (SOC) devices. Note that
113 the module will be called sb1250-duart.
118 select SERIAL_CORE_CONSOLE
129 bool "AT91 on-chip serial port support"
132 select SERIAL_CORE
133 select SERIAL_MCTRL_GPIO if GPIOLIB
134 select MFD_AT91_USART
136 This enables the driver for the on-chip UARTs of the Atmel
142 select SERIAL_CORE_CONSOLE
143 select SERIAL_EARLYCON
145 Say Y here if you wish to use an on-chip UART on a Atmel
204 select SERIAL_CORE
206 This enables the driver for the on-chip UARTs of the Amlogic
212 select SERIAL_CORE_CONSOLE
213 select SERIAL_EARLYCON
223 select SERIAL_CORE
224 select SERIAL_MCTRL_GPIO if GPIOLIB
226 This enables the driver for the on-chip UARTs of the Cirrus
232 select SERIAL_CORE_CONSOLE
242 select SERIAL_CORE
244 Support for the on-chip UARTs on the Samsung
263 Select the number of available UART ports for the Samsung S3C
269 select SERIAL_CORE_CONSOLE
270 select SERIAL_EARLYCON
272 Allow selection of the S3C24XX on-board serial ports for use as
285 select SERIAL_CORE
287 Support for the on-chip UARTs on the NVIDIA Tegra series SOCs
297 select SERIAL_CORE
299 Support for the mailbox-based TCU (Tegra Combined UART) serial port.
306 select SERIAL_CORE_CONSOLE
319 select SERIAL_CORE
321 MAX3100 chip support
326 select SERIAL_CORE
327 select REGMAP_SPI if SPI_MASTER
328 select REGMAP_I2C if I2C
333 that can be controlled through I2C or high-speed SPI.
340 select SERIAL_CORE
343 DZ11-family serial controllers for DECstations and VAXstations,
349 select SERIAL_CORE_CONSOLE
365 select SERIAL_CORE
379 select SERIAL_CORE_CONSOLE
395 select SERIAL_CORE
404 select SERIAL_CORE_CONSOLE
419 select SERIAL_CORE
420 select SERIAL_8250_PXA if SERIAL_8250=y
421 select SERIAL_PXA_NON8250 if !SERIAL_8250=y
436 select SERIAL_CORE_CONSOLE
437 select SERIAL_8250_CONSOLE if SERIAL_8250=y
455 select SERIAL_CORE
456 select SERIAL_MCTRL_GPIO if GPIOLIB
466 select SERIAL_CORE_CONSOLE
481 select SERIAL_CORE
482 select RATIONAL
483 select SERIAL_MCTRL_GPIO if GPIOLIB
491 select SERIAL_CORE_CONSOLE
506 select SERIAL_CORE
507 select SERIAL_EARLYCON
508 select SERIAL_CORE_CONSOLE
517 select SERIAL_CORE
527 select SERIAL_CORE_CONSOLE
528 select SERIAL_EARLYCON
546 select SERIAL_CORE
547 select SERIAL_CORE_CONSOLE
584 select SERIAL_CORE
603 select SERIAL_CORE_CONSOLE
632 select SERIAL_CORE
640 select SERIAL_CORE_CONSOLE
645 select SERIAL_CORE
646 select SERIAL_MCTRL_GPIO if GPIOLIB
660 select SERIAL_CORE_CONSOLE
666 select SERIAL_CORE_CONSOLE
667 select SERIAL_EARLYCON
679 select SERIAL_CORE
689 select SERIAL_CORE_CONSOLE
707 select SERIAL_CORE
723 select SERIAL_CORE_CONSOLE
730 select SERIAL_CORE
740 The pmac_zilog driver for the z85C30 chip on many powermacs
748 the pmac_zilog and 8250 drivers to co-exist, but may cause
750 access the built-in serial ports on powermacs will need to
755 unable to use the 8250 module for PCMCIA or other 16C550-style
764 select SERIAL_CORE_CONSOLE
773 select SERIAL_CORE
781 select SERIAL_CORE_CONSOLE
797 select SERIAL_CORE
808 select SERIAL_CORE_CONSOLE
818 select SERIAL_CORE
828 select SERIAL_CORE_CONSOLE
830 Select this options if you'd like to use one of the PSC serial port
838 Select the MPC52xx console baud rate.
846 select SERIAL_CORE
847 select FW_LOADER
859 select SERIAL_CORE
873 select SERIAL_CORE_CONSOLE
882 select SERIAL_CORE
887 box, for instance in order to become a dial-in server. This driver
896 tristate "MSM on-chip serial port support"
898 select SERIAL_CORE
903 select SERIAL_CORE_CONSOLE
904 select SERIAL_EARLYCON
907 tristate "QCOM on-chip GENI based serial port support"
910 select SERIAL_CORE
915 select SERIAL_CORE_CONSOLE
916 select SERIAL_EARLYCON
922 bool "VIA VT8500 on-chip serial port support"
924 select SERIAL_CORE
929 select SERIAL_CORE_CONSOLE
934 select SERIAL_CORE
940 with the omap-serial driver. DMA support can be enabled from platform
946 select SERIAL_CORE_CONSOLE
948 Select this option if you would like to use omap serial port as
961 select SERIAL_CORE
963 Select this option if you are building a kernel for a device that
970 select SERIAL_CORE_CONSOLE
971 select SERIAL_EARLYCON
973 Select this option if you would like to use a SiFive UART as the
986 select SERIAL_CORE
989 To compile this driver as a module, select M here. The
995 select SERIAL_CORE_CONSOLE
996 select SERIAL_EARLYCON
998 Select this option if you would like to use a Lantiq UART as the
1004 select SERIAL_CORE
1005 select FW_LOADER
1012 select SERIAL_CORE
1021 select SERIAL_CORE_CONSOLE
1030 select SERIAL_CORE
1035 SC16IS760 and SC16IS762. Select supported buses using options below.
1041 select SERIAL_SC16IS7XX_CORE if SERIAL_SC16IS7XX
1042 select REGMAP_I2C if I2C
1048 You must select at least one bus for the driver to be built.
1054 select SERIAL_SC16IS7XX_CORE if SERIAL_SC16IS7XX
1055 select REGMAP_SPI if SPI_MASTER
1060 You must select at least one bus for the driver to be built.
1064 select SERIAL_CORE
1071 select SERIAL_CORE
1081 BCM7xxx (STB) - DOCSIS console
1086 select SERIAL_CORE_CONSOLE
1087 select SERIAL_EARLYCON
1095 select SERIAL_CORE
1102 select SERIAL_CORE_CONSOLE
1108 select SERIAL_CORE
1115 select SERIAL_CORE_CONSOLE
1116 select SERIAL_EARLYCON
1123 select SERIAL_CORE_CONSOLE
1130 select SERIAL_CORE
1155 select SERIAL_CORE_CONSOLE
1156 select SERIAL_EARLYCON
1163 select SERIAL_CORE
1171 ML7213 IOH is for IVI(In-Vehicle Infotainment) use, ML7223 IOH is
1173 ML7213/ML7223/ML7831 is companion chip for Intel Atom E6xx series.
1179 select SERIAL_CORE_CONSOLE
1188 select SERIAL_CORE
1189 select SERIAL_MCTRL_GPIO if GPIOLIB
1197 select SERIAL_CORE_CONSOLE
1204 select SERIAL_CORE
1212 select SERIAL_CORE_CONSOLE
1213 select SERIAL_EARLYCON
1220 select SERIAL_CORE
1221 select SERIAL_MCTRL_GPIO if GPIOLIB
1224 built-in UART of the SoC, say Y to this option.
1232 select SERIAL_CORE_CONSOLE
1234 Enable a built-in UART port of the AR933X to be the system console.
1247 select SERIAL_CORE_CONSOLE
1248 select SERIAL_EARLYCON
1253 select SERIAL_CORE
1259 select SERIAL_CORE
1261 Driver for on-chip UART for ARC(Synopsys) for the legacy
1267 select SERIAL_CORE_CONSOLE
1268 select SERIAL_EARLYCON
1284 select SERIAL_CORE
1308 select SERIAL_CORE
1310 Support for the on-chip lpuart on some Freescale SOCs.
1315 select SERIAL_CORE_CONSOLE
1316 select SERIAL_EARLYCON
1324 select SERIAL_CORE
1326 Support for the on-chip LINFlexD UART on some Freescale SOCs.
1331 select SERIAL_CORE_CONSOLE
1332 select SERIAL_EARLYCON
1340 select SERIAL_CORE
1342 Support for the on-chip USART on Conexant Digicolor SoCs.
1347 select SERIAL_CORE_CONSOLE
1354 select SERIAL_CORE
1357 This driver is for the on-chip Asynchronous Serial Controller on
1367 select SERIAL_CORE_CONSOLE
1371 select SERIAL_CORE
1374 Say yes here to enable support for the MEN 16z135 High Speed UART IP-Core
1382 select SERIAL_CORE
1390 select SERIAL_CORE_CONSOLE
1391 select SERIAL_EARLYCON
1400 select SERIAL_CORE
1402 select SERIAL_MCTRL_GPIO if GPIOLIB
1404 This driver is for the on-chip Serial Controller on
1414 select SERIAL_CORE_CONSOLE
1415 select SERIAL_EARLYCON
1421 select SERIAL_CORE
1424 based on the Armada-3700 SoC and wish to use the on-board serial
1432 select SERIAL_CORE_CONSOLE
1433 select SERIAL_EARLYCON
1436 Say 'Y' here if you wish to use Armada-3700 UART as the system console.
1444 select SERIAL_CORE
1447 Say 'Y' here if you wish to use the on-board serial port.
1453 select SERIAL_CORE_CONSOLE
1454 select SERIAL_EARLYCON
1463 select SERIAL_CORE
1466 Say 'Y' here if you wish to use the on-board serial port.
1472 select SERIAL_CORE_CONSOLE
1473 select SERIAL_EARLYCON
1483 select SERIAL_CORE
1488 int "Maximum number of CSIO/UART ports (1-8)"
1497 select SERIAL_CORE_CONSOLE
1498 select SERIAL_EARLYCON
1510 select SERIAL_CORE
1512 This driver is for the FPGA-based LiteUART serial controller from LiteX
1529 select SERIAL_CORE_CONSOLE
1530 select SERIAL_EARLYCON
1532 Say 'Y' or 'M' here if you wish to use the FPGA-based LiteUART serial
1541 select SERIAL_CORE
1543 Select this option if you would like to use Sunplus serial port on
1548 called sunplus-uart.
1553 select SERIAL_CORE_CONSOLE
1554 select SERIAL_EARLYCON
1556 Select this option if you would like to use a Sunplus UART as the