5   Linux Driver for BusLogic MultiMaster and FlashPoint SCSI Host Adapters
90   all BusLogic Host Adapters.
98   all BusLogic Host Adapters.
114   to be checked for potential BusLogic Host Adapters.  It is initialized by
241   multiple host adapters share the same IRQ Channel.
517 		   Some early BusLogic Host Adapters may not recover  in blogic_cmd()
603   SCSI Host Adapters by interrogating the PCI Configuration Space on PCI
605   I/O Addresses.  It returns the number of PCI MultiMaster Host Adapters found.
622 	   Iterate over the MultiMaster PCI Host Adapters.  For each  in blogic_init_mm_probeinfo()
628 	   the Primary I/O Address, then any other PCI host adapters,  in blogic_init_mm_probeinfo()
629 	   and finally any host adapters located at the remaining  in blogic_init_mm_probeinfo()
695 		   ISA Compatible I/O Port. On PCI Host Adapters, the  in blogic_init_mm_probeinfo()
762 			blogic_warn("BusLogic: Too many Host Adapters detected\n", NULL);  in blogic_init_mm_probeinfo()
768 	   MultiMaster BIOS will recognize MultiMaster Host Adapters in  in blogic_init_mm_probeinfo()
772 	   MultiMaster Host Adapters in the order they are enumerated by  in blogic_init_mm_probeinfo()
779 	   Iterate over the older non-compliant MultiMaster PCI Host Adapters,  in blogic_init_mm_probeinfo()
826   Host Adapters by interrogating the PCI Configuration Space.  It returns the
827   number of FlashPoint Host Adapters found.
835 	   Interrogate PCI Configuration Space for any FlashPoint Host Adapters.  in blogic_init_fp_probeinfo()
892 			blogic_warn("BusLogic: Too many Host Adapters detected\n", NULL);  in blogic_init_fp_probeinfo()
900 	   The FlashPoint BIOS will scan for FlashPoint Host Adapters in the order of  in blogic_init_fp_probeinfo()
911   Probe Information to be checked for potential BusLogic SCSI Host Adapters by
914   FlashPoint and PCI MultiMaster Host Adapters are present, this driver will
915   probe for FlashPoint Host Adapters first unless the BIOS primary disk is
917   MultiMaster Host Adapters will be probed first.  The BusLogic Driver Options
926 	   FlashPoint Host Adapters; otherwise, default to the standard  in blogic_init_probeinfo_list()
963 				   Adapters are probed before FlashPoint Host  in blogic_init_probeinfo_list()
964 				   Adapters.  in blogic_init_probeinfo_list()
1017 	   FlashPoint Host Adapters are Probed by the FlashPoint SCCB Manager.  in blogic_probe()
1056 	   an I/O port that responded.  Adaptec Host Adapters do not  in blogic_probe()
1064 	   earlier BusLogic Host Adapters, including the undocumented  in blogic_probe()
1092 	   FlashPoint Host Adapters are Hard Reset by the FlashPoint  in blogic_hwreset()
1201 	   FlashPoint Host Adapters do not require this protection.  in blogic_checkadapter()
1207 	   BusLogic Host Adapters and true clones support this command.  in blogic_checkadapter()
1208 	   Adaptec 1542C series Host Adapters that respond to the Geometry  in blogic_checkadapter()
1249 	   Configuration Information for FlashPoint Host Adapters is  in blogic_rdconfig()
1357 	   BusLogic MultiMaster Host Adapters can be identified by their  in blogic_rdconfig()
1361 	   5.xx       BusLogic "W" Series Host Adapters:  in blogic_rdconfig()
1363 	   4.xx       BusLogic "C" Series Host Adapters:  in blogic_rdconfig()
1365 	   3.xx       BusLogic "S" Series Host Adapters:  in blogic_rdconfig()
1368 	   2.xx       BusLogic "A" Series Host Adapters:  in blogic_rdconfig()
1417 	   and save the DMA Channel for ISA Host Adapters.  in blogic_rdconfig()
1465 	   Termination Information from "W" series MultiMaster Host Adapters.  in blogic_rdconfig()
1485 	   AutoSCSI data from "W" and "C" series MultiMaster Host Adapters.  in blogic_rdconfig()
1524 	   series MultiMaster Host Adapters.  in blogic_rdconfig()
1542 	   supported by this driver for Wide and Narrow Host Adapters.  in blogic_rdconfig()
1556 	   cause a substantial performance penalty.  The host adapters  in blogic_rdconfig()
1589 	   all "W" series MultiMaster Host Adapters, on "C" series  in blogic_rdconfig()
1590 	   MultiMaster Host Adapters with firmware version 4.22 and above,  in blogic_rdconfig()
1591 	   and on "S" series MultiMaster Host Adapters with firmware version  in blogic_rdconfig()
1615 	   BusLogic BT-445S Host Adapters prior to board revision E have a  in blogic_rdconfig()
1618 	   incorrectly.  Only properly functioning BT-445S Host Adapters  in blogic_rdconfig()
1627 	   Host Adapters.  in blogic_rdconfig()
1930 	   FlashPoint Host Adapters do not use Outgoing and Incoming Mailboxes.  in blogic_initadapter()
1985 	   For Host Adapters that support Extended LUN Format CCBs, issue the  in blogic_initadapter()
2037 	   FlashPoint Host Adapters do not provide for Target Device Inquiry.  in blogic_inquiry()
2047 	   Issue the Inquire Target Devices command for host adapters with  in blogic_inquiry()
2049 	   ID 0 to 7 command for older host adapters.  This is necessary to  in blogic_inquiry()
2192   blogic_init probes for BusLogic Host Adapters at the standard
2195   returns the number of BusLogic Host Adapters successfully initialized and
2314 		   BusLogic Host Adapters.  in blogic_init()
2383 			   BusLogic Host Adapters, destroy the CCBs, Release  in blogic_init()
2414 	   FlashPoint Host Adapters must first be released by the FlashPoint  in blogic_deladapter()
2431 	   Host Adapters.  in blogic_deladapter()
2736   Adapters.
3232   may be enabled in AutoSCSI on FlashPoint Host Adapters and on "W" and "C"
3233   series MultiMaster Host Adapters, or by a dip switch setting on "S" and "A"
3234   series MultiMaster Host Adapters.  With Extended Translation enabled, drives
3507   for multiple host adapters may be specified either by separating the option
3511   adapters whereas the remaining options apply individually only to the