Lines Matching +full:usb +full:- +full:based
1 # SPDX-License-Identifier: GPL-2.0-only
3 # USB Network devices configuration
5 comment "Host-side USB support is needed for USB Network Adapter support"
6 depends on !USB && NET
9 tristate "USB Network Adapters"
10 default USB if USB
11 depends on USB && NET
16 tristate "USB CATC NetMate-based Ethernet device support"
19 Say Y if you want to use one of the following 10Mbps USB Ethernet
20 device based on the EL1210A chip. Supported devices are:
35 tristate "USB KLSI KL5USB101-based ethernet device support"
38 USB Ethernet adapters based on the KLSI KL5KUSB101B chipset:
40 ADS USB-10BT
41 ATEN USB Ethernet
42 ASANTE USB To Ethernet Adapter
43 AOX Endpoints USB Ethernet
45 D-Link DSB-650C and DU-E10
47 I-O DATA USB-ET/T
48 Jaton USB Ethernet Device Adapter
49 Kingston Technology USB Ethernet Adapter
51 Mobility USB-Ethernet Adapter
52 NetGear EA-101
56 SMC 2202USB
59 This driver is likely to work with most 10Mbps only USB Ethernet
61 SmartBridges smartNIC or on Belkin F5U111 devices - you should use
74 tristate "USB Pegasus/Pegasus-II based ethernet device support"
77 Say Y here if you know you have Pegasus or Pegasus-II based adapter.
78 If in doubt then look at <file:drivers/net/usb/pegasus.h> for the
82 is Pegasus or Pegasus II based then send me
89 tristate "USB RTL8150 based ethernet device support"
92 Say Y here if you have RTL8150 based usb-ethernet adapter.
100 tristate "Realtek RTL8152/RTL8153 Based USB Ethernet Adapters"
107 This option adds support for Realtek RTL8152 based USB 2.0
108 10/100 Ethernet adapters and RTL8153 based USB 3.0 10/100/1000
115 tristate "Microchip LAN78XX Based USB Ethernet Adapters"
122 This option adds support for Microchip LAN78XX based USB 2
123 & USB 3 10/100/1000 Ethernet adapters.
124 LAN7800 : USB 3 to 10/100/1000 Ethernet adapter
125 LAN7850 : USB 2 to 10/100/1000 Ethernet adapter
126 LAN7801 : USB 3 to 10/100/1000 Ethernet adapter (MAC only)
134 tristate "Multi-purpose USB Networking Framework"
137 This driver supports several kinds of network links over USB,
142 The USB host runs "usbnet", and the other end of the link might be:
144 - Another USB host, when using USB "network" or "data transfer"
149 - An intelligent USB gadget, perhaps embedding a Linux system.
152 CDC-Ethernet specification (including many cable modems).
154 - Network adapter hardware (like those for 10/100 Ethernet) which
158 a two-node link, or "eth0" for most CDC-Ethernet devices. Those
159 two-node links are most easily managed with Ethernet Bridging
162 For more information see <http://www.linux-usb.org/usbnet/>.
168 tristate "ASIX AX88xxx Based USB 2.0 Ethernet Adapters"
176 This option adds support for ASIX AX88xxx based USB 2.0
183 * Billionton Systems, GUSB2AM-1G-B
184 * Buffalo LUA-U2-KTX
185 * Corega FEther USB2-TX
186 * D-Link DUB-E100
190 * Sitecom LN-029
191 * Sitecom LN-028
192 * Intellinet USB 2.0 Ethernet
193 * ST Lab USB 2.0 Ethernet
194 * TrendNet TU2-ET100
200 tristate "ASIX AX88179/178A USB 3.0/2.0 to Gigabit Ethernet"
206 This option adds support for ASIX AX88179 based USB 3.0/2.0
212 * Sitcomm LN-032
225 from <http://www.usb.org/>.
228 that support USB connectivity, used for non-Microsoft USB hosts.
229 The Linux-USB CDC Ethernet Gadget driver is an open implementation.
252 from <http://www.usb.org/>.
266 Device USB Class Specification). The CDC NCM specification is
267 available from <http://www.usb.org/>.
273 * ST-Ericsson M700 LTE FDD/TDD Mobile Broadband Modem (ref. design)
274 * ST-Ericsson M5730 HSPA+ Mobile Broadband Modem (reference design)
275 * ST-Ericsson M570 HSPA+ Mobile Broadband Modem (reference design)
276 * ST-Ericsson M343 HSPA Mobile Broadband Modem (reference design)
285 This driver supports huawei-style NCM devices, that use NCM as a
302 available from <http://www.usb.org/>.
307 through the associated /dev/cdc-wdmx character device.
313 tristate "Davicom DM96xx based USB 10/100 ethernet devices"
318 based USB 10/100 Ethernet adapters.
321 tristate "CoreChip-sz SR9700 based USB 1.1 10/100 ethernet devices"
325 This option adds support for CoreChip-sz SR9700 based USB 1.1
329 tristate "CoreChip-sz SR9800 based USB 2.0 10/100 ethernet devices"
333 Say Y if you want to use one of the following 100Mbps USB Ethernet
334 device based on the CoreChip-sz SR9800 chip.
344 tristate "SMSC LAN75XX based USB 2.0 gigabit ethernet devices"
350 This option adds support for SMSC LAN75XX based USB 2.0
354 tristate "SMSC LAN95XX based USB 2.0 10/100 ethernet devices"
363 This option adds support for SMSC LAN95XX based USB 2.0
367 tristate "GeneSys GL620USB-A based cables"
370 Choose this option if you're using a host-to-host cable,
373 Note that the half-duplex "GL620USB" is not supported.
376 tristate "NetChip 1080 based cables (Laplink, ...)"
380 Choose this option if you're using a host-to-host cable based
385 tristate "Prolific PL-2301/2302/25A1/27A1 based cables"
390 Choose this option if you're using a host-to-host cable
394 tristate "MosChip MCS7830 based Ethernet adapters"
398 adapter based on the MosChip 7830 controller. This includes
406 This option enables hosting "Remote NDIS" USB networking links,
421 tristate "Simple USB Network Links (CDC Ethernet subset)"
425 This driver module supports USB network devices that can work
426 without any device-specific information. Select it if you have
429 Note that while many USB host-to-host cables can work in this mode,
436 bool "ALi M5632 based 'USB 2.0 Data Link' cables"
440 Choose this option if you're using a host-to-host cable
441 based on this design, which supports USB 2.0 high speed.
444 bool "AnchorChips 2720 based cables (Xircom PGUNET, ...)"
448 Choose this option if you're using a host-to-host cable
449 based on this design. Note that AnchorChips is now a
453 bool "eTEK based host-to-host cables (Advance, Belkin, ...)"
458 Choose this option if you're using a host-to-host cable
459 based on this design: two NetChip 2890 chips and an Atmel
468 Choose this option to support the "usb-eth" networking driver
470 such as the SA-11x0 and PXA-25x UDCs, or the tftp capabilities
473 Linux-based "Gumstix" PXA-25x based systems use this protocol
481 bool "Epson 2888 based firmware (DEVELOPMENT)"
485 Choose this option to support the usb networking links used
489 bool "KT Technology KC2190 based cables (InstaNet)"
493 Choose this option if you're using a host-to-host cable
503 Choose this option to support the usb networking links used by
504 Zaurus models like the SL-5000D, SL-5500, SL-5600, A-300, B-500.
508 If you install an alternate image, such as the Linux 2.6 based
510 protocol. Only the "eth-fd" or "net_fd" drivers in these devices
511 really need this non-conformant variant of CDC Ethernet (or in
515 tristate "Conexant CX82310 USB ethernet port"
518 Choose this option if you're using a Conexant CX82310-based ADSL
519 router with USB ethernet port. This driver is for routers only,
523 tristate "Samsung Kalmia based LTE USB modem"
526 Choose this option if you have a Samsung Kalmia based USB modem
527 as Samsung GT-B3730.
533 tristate "QMI WWAN driver for Qualcomm MSM based 3G and LTE modems"
537 Support WWAN LTE/3G devices based on Qualcomm Mobile Data Modem
547 * cdc-wdm: Qualcomm MSM Interface (QMI) protocol on /dev/cdc-wdmx
555 tristate "Option USB High Speed Mobile Devices"
556 depends on USB && RFKILL && TTY
566 tristate "Intellon PLC based usb adapter"
569 Choose this option if you're using a 14Mb USB-based PLC
579 "PC suite" USB profile.
582 tristate "Apple iPhone USB Ethernet driver"
594 tristate "USB-to-WWAN Driver for Sierra Wireless modems"
597 Choose this option if you have a Sierra Wireless USB-to-WWAN device.
607 Select this if you want to use an LG Electronics 4G/LTE usb modem
618 tristate "QingHeng CH9200 USB ethernet support"
622 Choose this option if you have a USB ethernet adapter with a QinHeng
629 tristate "Aquantia AQtion USB to 5/2.5GbE Controllers support"
633 This option adds support for Aquantia AQtion USB
634 Ethernet adapters based on AQC111U/AQC112 chips.
637 * Aquantia AQtion USB to 5GbE