Lines Matching +full:pmic +full:- +full:gpio
1 # SPDX-License-Identifier: GPL-2.0-only
50 See Documentation/ABI/testing/sysfs-class-led for details.
55 tristate "LED Support for Marvell 88PM860x PMIC"
59 This option enables support for on-chip LED drivers found on Marvell
60 Semiconductor 88PM8606 PMIC.
66 This option enables support for the AN30259A 3-channel
70 will be called leds-an30259a.
80 If you're looking for APU2/3, use the pcengines-apu2 driver.
84 module will be called leds-apu.
101 This option enables support for the AW2013 3-channel
105 will be called leds-aw2013.
132 CPCAP PMIC.
145 will be called leds-cr0014114.
158 will be called leds-el15203000.
201 ambient-light-sensor interface. The chip supports
202 hardware-accelerated blinking with maximum on and off periods of 9.8
211 The LM3642 is a 4MHz fixed-frequency synchronous boost
212 converter plus 1.5A constant current driver for a high-current
229 Zaurus models SL-5500 and SL-5600.
240 tristate "LED Support for Mediatek MT6323 PMIC"
244 This option enables support for on-chip LED drivers found on
245 Mediatek MT6323 PMIC.
248 tristate "LED Support for Samsung S3C24XX GPIO LEDs"
252 This option enables support for LEDs connected to GPIO lines
319 bool "Enable GPIO support for PCA9532"
323 Allow unused pins on PCA9532 to be used as gpio.
325 To use a pin as gpio pca9532_type in pca9532_platform data needs to
329 tristate "LED Support for GPIO connected LEDs"
333 This option enables support for the LEDs connected to GPIO
335 and they must be connected to the GPIO lines. The LEDs must be
349 module will be called leds-lp3944.
362 module will be called leds-lp3952.
373 module will be called leds-lp50xx.
431 tristate "LED support for the TI LP8788 PMIC"
435 This option enables support for the Keyboard LEDs on the LP8788 PMIC.
457 The driver supports two kinds of interface: using ledtrig-timer
477 module will be called leds-clevo-mail.
489 bool "Enable GPIO support for PCA955X"
493 Allow unused pins on PCA955X to be used as gpio.
495 To use a pin as gpio the pin type should be set to
517 tristate "LED Support for WM8350 AudioPlus PMIC"
522 Microelectronics WM8350 AudioPlus PMIC.
525 tristate "LED Support for DA9030/DA9034 PMIC"
529 This option enables support for on-chip LED drivers found
537 This option enables support for on-chip LED drivers found
538 on Dialog Semiconductor DA9052-BC and DA9053-AA/Bx PMICs.
587 LT3593 controller. This controller uses a special one-wire pulse
591 tristate "LED Support for ADP5520/ADP5501 PMIC"
595 This option enables support for on-chip LED drivers found
599 be called leds-adp5520.
602 tristate "LED Support for MC13XXX PMIC"
606 This option enables support for on-chip LED drivers found
607 on Freescale Semiconductor MC13783/MC13892/MC34708 PMIC.
610 tristate "LED support for Network Space v2 GPIO LEDs"
615 This option enables support for the dual-GPIO LEDs found on the
621 n090401 (Seagate NAS 4-Bay)
632 controlled through a GPIO extension bus.
641 ASIC3 LED GPIOs are inputs, not outputs, thus the leds-gpio driver
651 Driver support brightness control and hardware-assisted blinking.
662 tristate "LED support for Maxim MAX77650 PMIC"
668 tristate "LED support for MAX8997 PMIC"
671 This option enables support for on-chip LED drivers on
672 MAXIM MAX8997 PMIC.
696 will be called leds-menf21bmc.
708 called leds-is31fl319x.
714 Say Y here to include support for ISSI IS31FL32XX and Si-En SN32xx
715 LED controllers. They are I2C devices with multiple constant-current
716 channels, each with independent 256-level PWM control.
727 called leds-sc27xx-bltc.
748 will be called leds-powernv.
761 tristate "LED Support for the Qualcomm PM8058 PMIC"
766 the Qualcomm PM8058 PMIC.
783 module, choose 'M' here: the module will be called leds-mlxreg.
802 will be called leds-nic78bx.
858 will be called leds-ip30.