Lines Matching +full:pcf857x +full:- +full:compatible
1 # SPDX-License-Identifier: GPL-2.0-only
57 non-sleeping contexts. They can make bitbanged serial protocols
116 tristate "GPIO driver for 74xx-ICs with MMIO access"
120 Say yes here to support GPIO functionality for 74xx-compatible ICs
121 with MMIO access. Compatible models include:
136 If driver is built as a module it will be called gpio-altera.
297 tristate "Generic memory-mapped GPIO controller support (MMIO platform device)"
300 Say yes here to support basic platform_device memory-mapped GPIO controllers.
319 This GPIO controller supports double-edge interrupt and multi-core
338 ICH-based chipsets. Currently supported devices: ICH6, ICH7, ICH8
379 bool "Loongson-2/3 GPIO support"
382 Driver for GPIO functionality on Loongson-2F/3A/3B processors.
418 created by attaching a 16-bit latch to the bus.
469 Say yes here to support the on-chip GPIO lines on the OCTEON
504 tristate "Renesas R-Car and RZ/G GPIO support"
508 Say yes here to support GPIO on Renesas R-Car or RZ/G SoCs.
528 are grouped in four 8-bit wide ports.
535 A 32-bit single register GPIO fixed in/out implementation. This
558 maintain their value during backup/self-refresh.
576 via a SIOX bus and have a number of fixed-direction I/O lines.
584 This is a single-register MMIO GPIO driver for complex cases
655 tristate "TS-4800 DIO blocks and compatibles"
660 This driver support TS-4800 FPGA GPIO controllers.
663 tristate "Cavium ThunderX/OCTEON-TX GPIO"
670 Say yes here to support the on-chip GPIO lines on the ThunderX
671 and OCTEON-TX families of SoCs.
718 bool "APM X-Gene GPIO controller support"
721 This driver is to support the GPIO block within the APM X-Gene SoC
727 tristate "APM X-Gene GPIO standby controller support"
733 This driver supports the GPIO block within the APM X-Gene
776 tristate "ZynqMP ps-mode pin GPIO configuration driver"
780 Say yes here to support the ZynqMP ps-mode pin GPIO configuration
783 This ps-mode pin GPIO driver is based on GPIO framework. PS_MODE
784 is 4-bits boot mode pins. It sets and gets the status of
785 the ps-mode pin. Every pin can be configured as input/output.
795 tristate "GPIO support for AMD Fusion Controller Hub (G-series SOCs)"
798 as found on G-series SOCs (e.g. GX-412TC).
801 needs to be provided with platform-specific configuration.
812 ARMv7-based SoCs.
821 IDT 79RC3243X-based devices like Mikrotik RB532.
824 be called gpio-idt3243x.
828 menu "Port-mapped I/O GPIO drivers"
836 interfaces compatible with the venerable Intel 8255 Programmable
838 in the early 1970s but compatible interfaces are nowadays typically
841 If built as a module its name will be gpio-i8255.
844 tristate "ACCES 104-DIO-48E GPIO support"
850 Enables GPIO support for the ACCES 104-DIO-48E series (104-DIO-48E,
851 104-DIO-24E). The base port addresses for the devices may be
856 tristate "ACCES 104-IDIO-16 GPIO support"
861 Enables GPIO support for the ACCES 104-IDIO-16 family (104-IDIO-16,
862 104-IDIO-16E, 104-IDO-16, 104-IDIO-8, 104-IDIO-8E, 104-IDO-8). The
868 tristate "ACCES 104-IDI-48 GPIO support"
874 Enables GPIO support for the ACCES 104-IDI-48 family (104-IDI-48A,
875 104-IDI-48AC, 104-IDI-48B, 104-IDI-48BC). The base port addresses for
881 tristate "Fintek and Nuvoton Super-I/O GPIO support"
883 This option enables support for GPIOs found on Fintek Super-I/O
885 As well as Nuvoton Super-I/O chip NCT6116D.
888 be called f7188x-gpio.
891 tristate "Diamond Systems GPIO-MM GPIO support"
896 Enables GPIO support for the Diamond Systems GPIO-MM and GPIO-MM-12.
898 The Diamond Systems GPIO-MM device features 48 lines of digital I/O
931 active during S3. The suspend-powered GPIOs can be used to wake the
932 system from the Suspend-to-RAM state.
938 Twenty-one are powered by the core power rail and 9 from the
951 be called gpio-sch311x.
954 tristate "TS-5500 DIO blocks and compatibles"
959 blocks of the TS-5500: DIO1, DIO2 and the LCD port, and the TS-5600
972 boot-time parameter "gpio_winbond.gpios" with a bitmask of GPIO
976 be called gpio-winbond.
994 tristate "Avionic Design N-bit GPIO expander"
1010 Expander. This is used at least on the Cambria GW2358-4.
1016 GPIO driver for Maxim MAX7300 I2C-based GPIO expander.
1019 tristate "MAX7319, MAX7320-7327 I2C Port Expanders"
1021 Say yes here to support the MAX7319, MAX7320-7327 series of I2C
1023 Input (designated by 'I'), Push-Pull Output ('O'), or Open-Drain
1048 Say yes here to provide access to several register-oriented
1049 SMBus I/O expanders, made mostly by NXP or TI. Compatible
1073 tristate "PCA9570 4-Bit I2C GPO expander"
1078 be called gpio-pca9570.
1081 tristate "PCF857x, PCA{85,96}7x, and MAX732[89] I2C GPIO expanders"
1085 Say yes here to provide access to most "quasi-bidirectional" I2C
1088 some of them. Compatible models include:
1102 This driver provides an in-kernel interface to those GPIOs using
1103 platform-neutral GPIO calls.
1106 tristate "TPIC2810 8-Bit I2C GPO expander"
1111 be called gpio-tpic2810.
1119 Series supported include TS-4100, TS-4900, TS-7970 and TS-7990.
1129 This option enables support for on-chip GPIO found
1154 will be called gpio-bd71815.
1166 will be called gpio-bd71828.
1177 will be called gpio-bd9571mwv.
1186 Say Yes if you have a Intel SoC-based tablet with Crystal Cove PMIC
1190 called gpio-crystalcove.
1218 If driver is built as a module it will be called gpio-da9055.
1230 will be called gpio-dln2.
1241 tristate "Janz VMOD-TTL Digital IO Module"
1244 This enables support for the Janz VMOD-TTL Digital IO module.
1256 called gpio-kempld.
1274 called gpio-lp873x.
1284 called gpio-lp87565.
1335 called gpio-sl28cpld.
1368 they are input-only or output-only type.
1371 module will be called gpio-tn48m.
1412 There are 7 GPIOs and few sensor-related GPIOs supported
1418 tristate "TQ-Systems QTMX86 GPIO"
1429 Say yes here to access the GPIO signals of various multi-function
1453 Say Yes if you have an Intel SoC-based tablet with Whiskey Cove PMIC
1457 called gpio-wcove.
1505 This chip can be found on Miro, Hauppauge and STB TV-cards.
1510 Documentation/driver-api/gpio/bt8xxgpio.rst
1542 Hub) which is for IVI (In-Vehicle Infotainment) use.
1559 ML7223/ML7831 is completely compatible for Intel EG20T PCH.
1562 tristate "ACCES PCI-IDIO-16 GPIO support"
1565 Enables GPIO support for the ACCES PCI-IDIO-16. An interrupt is
1571 tristate "ACCES PCIe-IDIO-24 GPIO support"
1574 Enables GPIO support for the ACCES PCIe-IDIO-24 family (PCIe-IDIO-24,
1575 PCIe-IDI-24, PCIe-IDO-24, PCIe-IDIO-12). An interrupt is generated
1581 tristate "RDC R-321x GPIO support"
1602 tristate "74x164 serial-in/parallel-out 8-bits shift register"
1605 Driver for 74x164 compatible serial-in/parallel-out 8-outputs
1614 MAX31953 and MAX31963 industrial serializer, a daisy-chainable
1623 GPIO driver for Maxim MAX7301 SPI-based GPIO expander.
1626 tristate "Freescale MC33880 high-side/low-side switch"
1628 SPI driver for Freescale MC33880 high-side/low-side switch.
1632 tristate "Generic parallel-in/serial-out shift register"
1634 GPIO driver for SPI compatible parallel-in/serial-out shift
1638 tristate "EXAR XRA1403 16-bit GPIO expander"
1641 GPIO driver for EXAR XRA1403 16-bit SPI-based GPIO expander.
1678 - Assign permissions for a collection of GPIO lines to a user,
1679 - Export a collection of GPIO lines to a virtual machine,
1680 - Provide a generic driver for a GPIO-operated device in an
1691 tools/testing/selftests/gpio/gpio-mockup.sh. Reference the usage in
1699 Say Y here to enable guest support for virtio-based GPIO controllers.
1709 This enables the GPIO simulator - a configfs-based GPIO testing