Lines Matching +full:min +full:- +full:output +full:- +full:impedance
1 // SPDX-License-Identifier: GPL-2.0
3 * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
8 /dts-v1/;
10 #include "k3-j721s2-som-p0.dtsi"
11 #include <dt-bindings/net/ti-dp83867.h>
14 compatible = "ti,j721s2-evm", "ti,j721s2";
18 stdout-path = "serial2:115200n8";
32 evm_12v0: fixedregulator-evm12v0 {
34 compatible = "regulator-fixed";
35 regulator-name = "evm_12v0";
36 regulator-min-microvolt = <12000000>;
37 regulator-max-microvolt = <12000000>;
38 regulator-always-on;
39 regulator-boot-on;
42 vsys_3v3: fixedregulator-vsys3v3 {
43 /* Output of LM5140 */
44 compatible = "regulator-fixed";
45 regulator-name = "vsys_3v3";
46 regulator-min-microvolt = <3300000>;
47 regulator-max-microvolt = <3300000>;
48 vin-supply = <&evm_12v0>;
49 regulator-always-on;
50 regulator-boot-on;
53 vsys_5v0: fixedregulator-vsys5v0 {
54 /* Output of LM5140 */
55 compatible = "regulator-fixed";
56 regulator-name = "vsys_5v0";
57 regulator-min-microvolt = <5000000>;
58 regulator-max-microvolt = <5000000>;
59 vin-supply = <&evm_12v0>;
60 regulator-always-on;
61 regulator-boot-on;
64 vdd_mmc1: fixedregulator-sd {
65 /* Output of TPS22918 */
66 compatible = "regulator-fixed";
67 regulator-name = "vdd_mmc1";
68 regulator-min-microvolt = <3300000>;
69 regulator-max-microvolt = <3300000>;
70 regulator-boot-on;
71 enable-active-high;
72 vin-supply = <&vsys_3v3>;
76 vdd_sd_dv: gpio-regulator-TLV71033 {
77 /* Output of TLV71033 */
78 compatible = "regulator-gpio";
79 regulator-name = "tlv71033";
80 pinctrl-names = "default";
81 pinctrl-0 = <&vdd_sd_dv_pins_default>;
82 regulator-min-microvolt = <1800000>;
83 regulator-max-microvolt = <3300000>;
84 regulator-boot-on;
85 vin-supply = <&vsys_5v0>;
91 transceiver1: can-phy1 {
93 #phy-cells = <0>;
94 max-bitrate = <5000000>;
95 pinctrl-names = "default";
96 pinctrl-0 = <&mcu_mcan0_gpio_pins_default>;
97 standby-gpios = <&wkup_gpio0 69 GPIO_ACTIVE_LOW>;
98 enable-gpios = <&wkup_gpio0 0 GPIO_ACTIVE_HIGH>;
101 transceiver2: can-phy2 {
103 #phy-cells = <0>;
104 max-bitrate = <5000000>;
105 pinctrl-names = "default";
106 pinctrl-0 = <&mcu_mcan1_gpio_pins_default>;
107 standby-gpios = <&wkup_gpio0 2 GPIO_ACTIVE_HIGH>;
113 main_uart8_pins_default: main-uart8-pins-default {
114 pinctrl-single,pins = <
122 main_i2c3_pins_default: main-i2c3-pins-default {
123 pinctrl-single,pins = <
129 main_mmc1_pins_default: main-mmc1-pins-default {
130 pinctrl-single,pins = <
142 vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
143 pinctrl-single,pins = <
150 mcu_cpsw_pins_default: mcu-cpsw-pins-default {
151 pinctrl-single,pins = <
167 mcu_mdio_pins_default: mcu-mdio-pins-default {
168 pinctrl-single,pins = <
174 mcu_mcan0_pins_default: mcu-mcan0-pins-default {
175 pinctrl-single,pins = <
181 mcu_mcan1_pins_default: mcu-mcan1-pins-default {
182 pinctrl-single,pins = <
188 mcu_mcan0_gpio_pins_default: mcu-mcan0-gpio-pins-default {
189 pinctrl-single,pins = <
195 mcu_mcan1_gpio_pins_default: mcu-mcan1-gpio-pins-default {
196 pinctrl-single,pins = <
255 pinctrl-names = "default";
256 pinctrl-0 = <&main_uart8_pins_default>;
258 power-domains = <&k3_pds 357 TI_SCI_PD_SHARED>;
266 clock-frequency = <400000>;
271 gpio-controller;
272 #gpio-cells = <2>;
273 gpio-line-names = "PCIE_2L_MODE_SEL", "PCIE_2L_PERSTZ", "PCIE_2L_RC_RSTZ",
283 gpio-controller;
284 #gpio-cells = <2>;
285 gpio-line-names = "APPLE_AUTH_RSTZ", "MLB_RSTZ", "GPIO_USD_PWR_EN", "USBC_PWR_EN",
320 non-removable;
321 ti,driver-strength-ohm = <50>;
322 disable-wp;
327 pinctrl-0 = <&main_mmc1_pins_default>;
328 pinctrl-names = "default";
329 disable-wp;
330 vmmc-supply = <&vdd_mmc1>;
331 vqmmc-supply = <&vdd_sd_dv>;
335 pinctrl-names = "default";
336 pinctrl-0 = <&mcu_cpsw_pins_default &mcu_mdio_pins_default>;
340 phy0: ethernet-phy@0 {
342 ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
343 ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
344 ti,min-output-impedance;
349 phy-mode = "rgmii-rxid";
350 phy-handle = <&phy0>;
354 pinctrl-names = "default";
355 pinctrl-0 = <&mcu_mcan0_pins_default>;
360 pinctrl-names = "default";
361 pinctrl-0 = <&mcu_mcan1_pins_default>;