Lines Matching +full:vdd +full:- +full:buck +full:- +full:supply
1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
14 #include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h>
15 #include <dt-bindings/iio/qcom,spmi-adc7-pmr735a.h>
16 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
17 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
34 wcd9385: audio-codec-1 {
35 compatible = "qcom,wcd9385-codec";
36 pinctrl-names = "default", "sleep";
37 pinctrl-0 = <&wcd_reset_n>, <&us_euro_hs_sel>;
38 pinctrl-1 = <&wcd_reset_n_sleep>, <&us_euro_hs_sel>;
40 reset-gpios = <&tlmm 83 GPIO_ACTIVE_HIGH>;
41 us-euro-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;
43 qcom,rx-device = <&wcd_rx>;
44 qcom,tx-device = <&wcd_tx>;
46 vdd-rxtx-supply = <&vreg_l18b_1p8>;
47 vdd-io-supply = <&vreg_l18b_1p8>;
48 vdd-buck-supply = <&vreg_l17b_1p8>;
49 vdd-mic-bias-supply = <&vreg_bob>;
51 qcom,micbias1-microvolt = <1800000>;
52 qcom,micbias2-microvolt = <1800000>;
53 qcom,micbias3-microvolt = <1800000>;
54 qcom,micbias4-microvolt = <1800000>;
56 qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000
58 qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
59 qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
60 #sound-dai-cells = <1>;
66 compatible = "pwm-backlight";
69 enable-gpios = <&pm8350c_gpios 7 GPIO_ACTIVE_HIGH>;
70 pinctrl-names = "default";
71 pinctrl-0 = <&pmic_edp_bl_en>;
90 pm7325-regulators {
91 compatible = "qcom,pm7325-rpmh-regulators";
92 qcom,pmic-id = "b";
97 regulator-min-microvolt = <1856000>;
98 regulator-max-microvolt = <2040000>;
106 regulator-min-microvolt = <535000>;
107 regulator-max-microvolt = <1120000>;
113 regulator-min-microvolt = <1256000>;
114 regulator-max-microvolt = <1500000>;
119 regulator-min-microvolt = <825000>;
120 regulator-max-microvolt = <925000>;
121 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
126 regulator-min-microvolt = <2700000>;
127 regulator-max-microvolt = <3544000>;
128 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
143 regulator-min-microvolt = <1140000>;
144 regulator-max-microvolt = <1260000>;
145 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
153 regulator-min-microvolt = <2960000>;
154 regulator-max-microvolt = <2960000>;
155 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
159 regulator-min-microvolt = <1700000>;
160 regulator-max-microvolt = <1900000>;
161 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
170 regulator-min-microvolt = <1800000>;
171 regulator-max-microvolt = <2000000>;
172 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
185 regulator-min-microvolt = <1800000>;
186 regulator-max-microvolt = <1800000>;
187 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
191 pm8350c-regulators {
192 compatible = "qcom,pm8350c-rpmh-regulators";
193 qcom,pmic-id = "c";
204 regulator-min-microvolt = <2190000>;
205 regulator-max-microvolt = <2210000>;
210 regulator-min-microvolt = <1010000>;
211 regulator-max-microvolt = <1170000>;
222 regulator-min-microvolt = <1800000>;
223 regulator-max-microvolt = <1980000>;
224 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
228 regulator-min-microvolt = <1620000>;
229 regulator-max-microvolt = <1980000>;
230 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
234 regulator-min-microvolt = <2800000>;
235 regulator-max-microvolt = <3540000>;
236 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
241 regulator-min-microvolt = <1620000>;
242 regulator-max-microvolt = <3300000>;
243 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
248 regulator-min-microvolt = <1620000>;
249 regulator-max-microvolt = <3300000>;
250 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
255 regulator-min-microvolt = <1800000>;
256 regulator-max-microvolt = <2950000>;
257 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
261 regulator-min-microvolt = <3000000>;
262 regulator-max-microvolt = <3544000>;
263 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
267 regulator-min-microvolt = <1620000>;
268 regulator-max-microvolt = <2000000>;
269 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
273 regulator-min-microvolt = <2960000>;
274 regulator-max-microvolt = <2960000>;
275 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
303 regulator-min-microvolt = <720000>;
304 regulator-max-microvolt = <1050000>;
305 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
309 regulator-min-microvolt = <2800000>;
310 regulator-max-microvolt = <3544000>;
311 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
315 regulator-min-microvolt = <1650000>;
316 regulator-max-microvolt = <2000000>;
317 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
321 regulator-min-microvolt = <2700000>;
322 regulator-max-microvolt = <3544000>;
323 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
330 regulator-min-microvolt = <3008000>;
331 regulator-max-microvolt = <3960000>;
332 regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
341 modem-init;
345 vdd-micb-supply = <&vreg_bob>;
350 aux-bus {
352 compatible = "edp-panel";
357 #address-cells = <1>;
358 #size-cells = <0>;
362 remote-endpoint = <&mdss_edp_out>;
371 remote-endpoint = <&edp_panel_in>;
375 vdda-pll-supply = <&vdd_a_edp_0_0p9>;
376 vdda-phy-supply = <&vdd_a_edp_0_1p2>;
380 vdda-phy-supply = <&vreg_l10c_0p88>;
381 vdda-pll-supply = <&vreg_l6b_1p2>;
385 pinctrl-names = "default";
386 pinctrl-0 = <&pmic_edp_bl_pwm>;
390 pmk8350-die-temp@3 {
393 qcom,pre-scaling = <1 1>;
396 pmr735a-die-temp@403 {
399 qcom,pre-scaling = <1 1>;
404 vcc-supply = <&vdd_qfprom>;
409 vmmc-supply = <&vreg_l7b_2p5>;
410 vqmmc-supply = <&vreg_l19b_1p8>;
412 non-removable;
413 no-sd;
414 no-sdio;
421 #sound-dai-cells = <1>;
422 qcom,rx-port-mapping = <1 2 3 4 5>;
430 #sound-dai-cells = <1>;
431 qcom,tx-port-mapping = <1 2 3 4>;
436 compatible = "qcom,geni-debug-uart";
443 /delete-property/ interrupts;
444 interrupts-extended = <&intc GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>,
446 pinctrl-names = "default", "sleep";
447 …pinctrl-1 = <&qup_uart7_sleep_cts>, <&qup_uart7_sleep_rts>, <&qup_uart7_sleep_tx>, <&qup_uart7_sle…
450 compatible = "qcom,wcn6750-bt";
451 pinctrl-names = "default";
452 pinctrl-0 = <&mos_bt_en>;
453 enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>;
454 swctrl-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>;
455 vddaon-supply = <&vreg_s7b_0p952>;
456 vddbtcxmx-supply = <&vreg_s7b_0p952>;
457 vddrfacmn-supply = <&vreg_s7b_0p952>;
458 vddrfa0p8-supply = <&vreg_s7b_0p952>;
459 vddrfa1p7-supply = <&vdd19_pmu_rfa_i>;
460 vddrfa1p2-supply = <&vdd13_pmu_rfa_i>;
461 vddrfa2p2-supply = <&vreg_s1c_2p2>;
462 vddasd-supply = <&vreg_l11c_2p8>;
463 vddio-supply = <&vreg_l18b_1p8>;
464 max-speed = <3200000>;
469 vdda-pll-supply = <&vdd_a_usbhs_core>;
470 vdda33-supply = <&vdd_a_usbhs_3p1>;
471 vdda18-supply = <&vdd_a_usbhs_1p8>;
475 vdda-phy-supply = <&vdd_a_usbssdp_0_1p2>;
476 vdda-pll-supply = <&vdd_a_usbssdp_0_core>;
480 vdda-pll-supply = <&vdd_a_usbhs_core>;
481 vdda33-supply = <&vdd_a_usbhs_3p1>;
482 vdda18-supply = <&vdd_a_usbhs_1p8>;
486 * PINCTRL - ADDITIONS TO NODES IN PARENT DEVICE TREE FILES
494 bias-pull-down;
506 bias-disable;
507 drive-strength = <2>;
513 * Configure a bias-bus-hold on CTS to lower power
519 bias-bus-hold;
525 bias-disable;
526 drive-strength = <2>;
532 bias-disable;
533 drive-strength = <2>;
539 * Configure a pull-up on RX. This is needed to avoid
541 * in tri-state (module powered off or not driving the
544 bias-pull-up;
549 bias-disable;
550 drive-strength = <16>;
554 bias-pull-up;
555 drive-strength = <10>;
559 bias-pull-up;
560 drive-strength = <10>;
564 bias-pull-down;
568 * PINCTRL - QCARD
577 pmic_edp_bl_en: pmic-edp-bl-en-state {
580 bias-disable;
581 qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
584 output-low;
587 pmic_edp_bl_pwm: pmic-edp-bl-pwm-state {
590 bias-disable;
591 qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
592 output-low;
593 power-source = <0>;
598 mos_bt_en: mos-bt-en-pins {
601 drive-strength = <2>;
602 output-low;
606 qup_uart7_sleep_cts: qup-uart7-sleep-cts-pins {
610 * Configure a bias-bus-hold on CTS to lower power
616 bias-bus-hold;
620 qup_uart7_sleep_rts: qup-uart7-sleep-rts-pins {
624 * Configure pull-down on RTS. As RTS is active low
629 bias-pull-down;
633 qup_uart7_sleep_rx: qup-uart7-sleep-rx-pins {
637 * Configure a pull-up on RX. This is needed to avoid
641 bias-pull-up;
645 qup_uart7_sleep_tx: qup-uart7-sleep-tx-pins {
649 * Configure pull-up on TX when it isn't actively driven
652 bias-pull-up;
655 ts_int_conn: ts-int-conn-pins {
658 bias-pull-up;
661 ts_rst_conn: ts-rst-conn-pins {
664 drive-strength = <2>;
667 us_euro_hs_sel: us-euro-hs-sel {
670 bias-pull-down;
671 drive-strength = <2>;
674 wcd_reset_n: wcd-reset-n {
677 drive-strength = <8>;
680 wcd_reset_n_sleep: wcd-reset-n-sleep {
683 drive-strength = <8>;
684 bias-disable;