Lines Matching +full:vdda +full:- +full:pll +full:- +full:supply
1 // SPDX-License-Identifier: BSD-3-Clause
7 /dts-v1/;
9 #include <dt-bindings/gpio/gpio.h>
10 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
11 #include <dt-bindings/spmi/spmi.h>
17 compatible = "qcom,sa8295p-adp", "qcom,sa8540p";
24 stdout-path = "serial0:115200n8";
29 pmm8540-a-regulators {
30 compatible = "qcom,pm8150-rpmh-regulators";
31 qcom,pmic-id = "a";
34 regulator-name = "vreg_l3a";
35 regulator-min-microvolt = <1200000>;
36 regulator-max-microvolt = <1208000>;
37 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
41 regulator-name = "vreg_l5a";
42 regulator-min-microvolt = <912000>;
43 regulator-max-microvolt = <912000>;
44 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
48 regulator-name = "vreg_l7a";
49 regulator-min-microvolt = <1800000>;
50 regulator-max-microvolt = <1800000>;
51 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
55 regulator-name = "vreg_l13a";
56 regulator-min-microvolt = <3072000>;
57 regulator-max-microvolt = <3072000>;
58 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
62 pmm8540-c-regulators {
63 compatible = "qcom,pm8150-rpmh-regulators";
64 qcom,pmic-id = "c";
67 regulator-name = "vreg_l1c";
68 regulator-min-microvolt = <912000>;
69 regulator-max-microvolt = <912000>;
70 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
74 regulator-name = "vreg_l2c";
75 regulator-min-microvolt = <3072000>;
76 regulator-max-microvolt = <3072000>;
77 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
81 regulator-name = "vreg_l3c";
82 regulator-min-microvolt = <1200000>;
83 regulator-max-microvolt = <1200000>;
84 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
85 regulator-allow-set-load;
86 regulator-allowed-modes =
92 regulator-name = "vreg_l4c";
93 regulator-min-microvolt = <1200000>;
94 regulator-max-microvolt = <1208000>;
95 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
99 regulator-name = "vreg_l6c";
100 regulator-min-microvolt = <1200000>;
101 regulator-max-microvolt = <1200000>;
102 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
103 regulator-allow-set-load;
104 regulator-allowed-modes =
110 regulator-name = "vreg_l7c";
111 regulator-min-microvolt = <1800000>;
112 regulator-max-microvolt = <1800000>;
113 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
117 regulator-name = "vreg_l10c";
118 regulator-min-microvolt = <2504000>;
119 regulator-max-microvolt = <2504000>;
120 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
121 regulator-allow-set-load;
122 regulator-allowed-modes =
128 regulator-name = "vreg_l17c";
129 regulator-min-microvolt = <2504000>;
130 regulator-max-microvolt = <2504000>;
131 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
132 regulator-allow-set-load;
133 regulator-allowed-modes =
139 pmm8540-g-regulators {
140 compatible = "qcom,pm8150-rpmh-regulators";
141 qcom,pmic-id = "g";
144 regulator-name = "vreg_l3g";
145 regulator-min-microvolt = <1200000>;
146 regulator-max-microvolt = <1200000>;
147 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
151 regulator-name = "vreg_l7g";
152 regulator-min-microvolt = <1800000>;
153 regulator-max-microvolt = <1800000>;
154 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
158 regulator-name = "vreg_l8g";
159 regulator-min-microvolt = <880000>;
160 regulator-max-microvolt = <880000>;
161 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
171 compatible = "qcom,geni-debug-uart";
176 firmware-name = "qcom/sa8540p/adsp.mbn";
181 firmware-name = "qcom/sa8540p/cdsp.mbn";
186 firmware-name = "qcom/sa8540p/cdsp1.mbn";
192 compatible = "qcom,pm8150", "qcom,spmi-pmic";
194 #address-cells = <1>;
195 #size-cells = <0>;
198 compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
200 gpio-controller;
201 gpio-ranges = <&pm8450a_gpios 0 0 10>;
202 #gpio-cells = <2>;
203 interrupt-controller;
204 #interrupt-cells = <2>;
209 compatible = "qcom,pm8150", "qcom,spmi-pmic";
211 #address-cells = <1>;
212 #size-cells = <0>;
215 compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
217 gpio-controller;
218 gpio-ranges = <&pm8450c_gpios 0 0 10>;
219 #gpio-cells = <2>;
220 interrupt-controller;
221 #interrupt-cells = <2>;
226 compatible = "qcom,pm8150", "qcom,spmi-pmic";
228 #address-cells = <1>;
229 #size-cells = <0>;
232 compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
234 gpio-controller;
235 gpio-ranges = <&pm8450e_gpios 0 0 10>;
236 #gpio-cells = <2>;
237 interrupt-controller;
238 #interrupt-cells = <2>;
243 compatible = "qcom,pm8150", "qcom,spmi-pmic";
245 #address-cells = <1>;
246 #size-cells = <0>;
249 compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
251 gpio-controller;
252 gpio-ranges = <&pm8450g_gpios 0 0 10>;
253 #gpio-cells = <2>;
254 interrupt-controller;
255 #interrupt-cells = <2>;
261 reset-gpios = <&tlmm 228 GPIO_ACTIVE_LOW>;
263 vcc-supply = <&vreg_l17c>;
264 vcc-max-microamp = <800000>;
265 vccq-supply = <&vreg_l6c>;
266 vccq-max-microamp = <900000>;
272 vdda-phy-supply = <&vreg_l8g>;
273 vdda-pll-supply = <&vreg_l3g>;
279 reset-gpios = <&tlmm 229 GPIO_ACTIVE_LOW>;
281 vcc-supply = <&vreg_l10c>;
282 vcc-max-microamp = <800000>;
283 vccq-supply = <&vreg_l3c>;
284 vccq-max-microamp = <900000>;
290 vdda-phy-supply = <&vreg_l8g>;
291 vdda-pll-supply = <&vreg_l3g>;
301 /* TODO: Define USB-C connector properly */
306 vdda-pll-supply = <&vreg_l5a>;
307 vdda18-supply = <&vreg_l7a>;
308 vdda33-supply = <&vreg_l13a>;
314 vdda-phy-supply = <&vreg_l3a>;
315 vdda-pll-supply = <&vreg_l5a>;
325 /* TODO: Define USB-C connector properly */
330 vdda-pll-supply = <&vreg_l1c>;
331 vdda18-supply = <&vreg_l7c>;
332 vdda33-supply = <&vreg_l2c>;
338 vdda-phy-supply = <&vreg_l4c>;
339 vdda-pll-supply = <&vreg_l1c>;
345 vdda-pll-supply = <&vreg_l5a>;
346 vdda18-supply = <&vreg_l7g>;
347 vdda33-supply = <&vreg_l13a>;
353 vdda-pll-supply = <&vreg_l5a>;
354 vdda18-supply = <&vreg_l7g>;
355 vdda33-supply = <&vreg_l13a>;
361 vdda-pll-supply = <&vreg_l5a>;
362 vdda18-supply = <&vreg_l7g>;
363 vdda33-supply = <&vreg_l13a>;
369 vdda-pll-supply = <&vreg_l5a>;
370 vdda18-supply = <&vreg_l7g>;
371 vdda33-supply = <&vreg_l13a>;
377 vdda-phy-supply = <&vreg_l3a>;
378 vdda-pll-supply = <&vreg_l5a>;
384 vdda-phy-supply = <&vreg_l3a>;
385 vdda-pll-supply = <&vreg_l5a>;
391 clock-frequency = <38400000>;