Lines Matching +full:assigned +full:- +full:clock +full:- +full:parents
1 // SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
3 * Copyright 2020-2021 TQ-Systems GmbH
6 /dts-v1/;
8 #include "imx8mm-tqma8mqml.dtsi"
12 model = "TQ-Systems GmbH i.MX8MM TQMa8MxML on MBa8Mx";
13 compatible = "tq,imx8mm-tqma8mqml-mba8mx", "tq,imx8mm-tqma8mqml", "fsl,imx8mm";
24 reg_usdhc2_vmmc: regulator-vmmc {
25 compatible = "regulator-fixed";
26 pinctrl-names = "default";
27 pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
28 regulator-name = "VSD_3V3";
29 regulator-min-microvolt = <3300000>;
30 regulator-max-microvolt = <3300000>;
32 enable-active-high;
33 startup-delay-us = <100>;
34 off-on-delay-us = <12000>;
38 compatible = "gpio-usb-b-connector", "usb-b-connector";
41 pinctrl-names = "default";
42 pinctrl-0 = <&pinctrl_usb1_connector>;
43 id-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
46 #address-cells = <1>;
47 #size-cells = <0>;
52 remote-endpoint = <&usb1_drd_sw>;
63 gpio-controller;
64 #gpio-cells = <2>;
65 vcc-supply = <®_vcc_3v3>;
66 pinctrl-names = "default";
67 pinctrl-0 = <&pinctrl_expander>;
68 interrupt-parent = <&gpio1>;
70 interrupt-controller;
71 #interrupt-cells = <2>;
81 reset-gpio = <&expander0 14 GPIO_ACTIVE_LOW>;
84 clock-names = "pcie", "pcie_aux", "pcie_bus";
85 assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>,
87 assigned-clock-rates = <10000000>, <250000000>;
88 assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>,
94 assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
95 assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
96 clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k", "pll11k";
104 clock-names = "mclk";
109 assigned-clocks = <&clk IMX8MM_CLK_UART1>;
110 assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
114 assigned-clocks = <&clk IMX8MM_CLK_UART2>;
115 assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
119 pinctrl-names = "default";
120 pinctrl-0 = <&pinctrl_usbotg1>;
122 srp-disable;
123 hnp-disable;
124 adp-disable;
125 power-active-high;
126 over-current-active-low;
127 usb-role-switch;
132 remote-endpoint = <&usb_dr_connector>;
139 disable-over-current;
140 vbus-supply = <®_hub_vbus>;
254 pinctrl_usb1_connector: usb1-connectorgrp {
272 pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
282 pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {