Lines Matching +full:pullup +full:- +full:uv
1 // SPDX-License-Identifier: GPL-2.0
11 /dts-v1/;
13 #include <dt-bindings/clock/samsung,s2mps11.h>
14 #include <dt-bindings/gpio/gpio.h>
15 #include <dt-bindings/input/input.h>
16 #include <dt-bindings/interrupt-controller/irq.h>
17 #include <dt-bindings/sound/samsung-i2s.h>
48 stdout-path = &serial_1;
56 gpio-keys {
57 compatible = "gpio-keys";
59 power-key {
63 debounce-interval = <10>;
66 volume-up-key {
69 label = "volume-up key";
70 debounce-interval = <10>;
73 volume-down-key {
76 label = "volume-down key";
77 debounce-interval = <10>;
80 homepage-key {
84 debounce-interval = <10>;
88 i2c_max98504: i2c-gpio-0 {
89 compatible = "i2c-gpio";
90 sda-gpios = <&gpd0 1 GPIO_ACTIVE_HIGH>;
91 scl-gpios = <&gpd0 0 GPIO_ACTIVE_HIGH>;
92 i2c-gpio,delay-us = <2>;
93 #address-cells = <1>;
94 #size-cells = <0>;
99 maxim,rx-path = <1>;
100 maxim,tx-path = <1>;
101 maxim,tx-channel-mask = <3>;
102 maxim,tx-channel-source = <2>;
106 irda_regulator: irda-regulator {
107 compatible = "regulator-fixed";
108 enable-active-high;
110 regulator-name = "irda_regulator";
114 compatible = "samsung,tm2-audio";
115 audio-codec = <&wm5110>, <&hdmi>;
116 i2s-controller = <&i2s0 0>, <&i2s1 0>;
117 audio-amplifier = <&max98504>;
118 mic-bias-gpios = <&gpr3 2 GPIO_ACTIVE_HIGH>;
120 samsung,audio-routing =
138 vdd-supply = <&ldo3_reg>;
141 thermistor-ap {
143 pullup-uv = <1800000>;
144 pullup-ohm = <100000>;
145 pulldown-ohm = <0>;
146 io-channels = <&adc 0>;
149 thermistor-battery {
151 pullup-uv = <1800000>;
152 pullup-ohm = <100000>;
153 pulldown-ohm = <0>;
154 io-channels = <&adc 1>;
155 #thermal-sensor-cells = <0>;
158 thermistor-charger {
160 pullup-uv = <1800000>;
161 pullup-ohm = <100000>;
162 pulldown-ohm = <0>;
163 io-channels = <&adc 2>;
168 devfreq-events = <&ppmu_event0_d0_general>, <&ppmu_event0_d1_general>;
169 vdd-supply = <&buck4_reg>;
170 exynos,saturation-ratio = <10>;
220 assigned-clocks = <&cmu_aud CLK_MOUT_AUD_PLL_USER>,
241 assigned-clock-parents = <&cmu_top CLK_FOUT_AUD_PLL>,
250 assigned-clock-rates = <0>, <0>, <0>, <0>, <0>, <0>, <0>, <0>,
257 assigned-clocks = <&cmu_top CLK_MOUT_SCLK_USBDRD30>,
267 assigned-clock-parents = <&cmu_top CLK_MOUT_BUS_PLL_USER>,
275 assigned-clock-rates = <0>, <0>, <0>, <0>, <0>, <0>, <0>, <0>,
280 assigned-clocks = <&cmu_gscl CLK_MOUT_ACLK_GSCL_111_USER>,
282 assigned-clock-parents = <&cmu_top CLK_ACLK_GSCL_111>,
287 assigned-clocks = <&cmu_mfc CLK_MOUT_ACLK_MFC_400_USER>;
288 assigned-clock-parents = <&cmu_top CLK_ACLK_MFC_400>;
292 assigned-clocks = <&cmu_mif CLK_MOUT_SCLK_DSD_A>, <&cmu_mif CLK_DIV_SCLK_DSD>;
293 assigned-clock-parents = <&cmu_mif CLK_MOUT_MFC_PLL_DIV2>;
294 assigned-clock-rates = <0>, <333000000>;
298 assigned-clocks = <&cmu_mscl CLK_MOUT_ACLK_MSCL_400_USER>,
302 assigned-clock-parents = <&cmu_top CLK_ACLK_MSCL_400>,
309 assigned-clocks = <&cmu_top CLK_FOUT_AUD_PLL>;
310 assigned-clock-rates = <196608001>;
314 cpu-supply = <&buck3_reg>;
318 cpu-supply = <&buck2_reg>;
329 #address-cells = <1>;
330 #size-cells = <0>;
335 remote-endpoint = <&hdmi_to_tv>;
343 vddcore-supply = <&ldo6_reg>;
344 vddio-supply = <&ldo7_reg>;
345 samsung,burst-clock-frequency = <512000000>;
346 samsung,esc-clock-frequency = <16000000>;
347 samsung,pll-clock-frequency = <24000000>;
348 pinctrl-names = "default";
349 pinctrl-0 = <&te_irq>;
353 mali-supply = <&buck6_reg>;
358 hpd-gpios = <&gpa3 0 GPIO_ACTIVE_HIGH>;
360 vdd-supply = <&ldo6_reg>;
361 vdd_osc-supply = <&ldo7_reg>;
362 vdd_pll-supply = <&ldo6_reg>;
365 #address-cells = <1>;
366 #size-cells = <0>;
371 remote-endpoint = <&tv_to_hdmi>;
378 remote-endpoint = <&mhl_to_hdmi>;
386 clock-frequency = <2500000>;
389 compatible = "samsung,s2mps13-pmic";
390 interrupt-parent = <&gpa0>;
393 samsung,s2mps11-wrstbi-ground;
394 wakeup-source;
397 compatible = "samsung,s2mps13-clk";
398 #clock-cells = <1>;
399 clock-output-names = "s2mps13_ap", "s2mps13_cp",
405 regulator-name = "VDD_ALIVE_0.9V_AP";
406 regulator-min-microvolt = <900000>;
407 regulator-max-microvolt = <900000>;
408 regulator-always-on;
412 regulator-name = "VDDQ_MMC2_2.8V_AP";
413 regulator-min-microvolt = <2800000>;
414 regulator-max-microvolt = <2800000>;
415 regulator-always-on;
416 regulator-state-mem {
417 regulator-off-in-suspend;
422 regulator-name = "VDD1_E_1.8V_AP";
423 regulator-min-microvolt = <1800000>;
424 regulator-max-microvolt = <1800000>;
425 regulator-always-on;
429 regulator-name = "VDD10_MIF_PLL_1.0V_AP";
430 regulator-min-microvolt = <1300000>;
431 regulator-max-microvolt = <1300000>;
432 regulator-always-on;
433 regulator-state-mem {
434 regulator-off-in-suspend;
439 regulator-name = "VDD10_DPLL_1.0V_AP";
440 regulator-min-microvolt = <1000000>;
441 regulator-max-microvolt = <1000000>;
442 regulator-always-on;
443 regulator-state-mem {
444 regulator-off-in-suspend;
449 regulator-name = "VDD10_MIPI2L_1.0V_AP";
450 regulator-min-microvolt = <1000000>;
451 regulator-max-microvolt = <1000000>;
452 regulator-state-mem {
453 regulator-off-in-suspend;
458 regulator-name = "VDD18_MIPI2L_1.8V_AP";
459 regulator-min-microvolt = <1800000>;
460 regulator-max-microvolt = <1800000>;
461 regulator-always-on;
462 regulator-state-mem {
463 regulator-off-in-suspend;
468 regulator-name = "VDD18_LLI_1.8V_AP";
469 regulator-min-microvolt = <1800000>;
470 regulator-max-microvolt = <1800000>;
471 regulator-always-on;
472 regulator-state-mem {
473 regulator-off-in-suspend;
478 regulator-name = "VDD18_ABB_ETC_1.8V_AP";
479 regulator-min-microvolt = <1800000>;
480 regulator-max-microvolt = <1800000>;
481 regulator-always-on;
482 regulator-state-mem {
483 regulator-off-in-suspend;
488 regulator-name = "VDD33_USB30_3.0V_AP";
489 regulator-min-microvolt = <3000000>;
490 regulator-max-microvolt = <3000000>;
491 regulator-state-mem {
492 regulator-off-in-suspend;
497 regulator-name = "VDD_INT_M_1.0V_AP";
498 regulator-min-microvolt = <1000000>;
499 regulator-max-microvolt = <1000000>;
500 regulator-always-on;
501 regulator-state-mem {
502 regulator-off-in-suspend;
507 regulator-name = "VDD_KFC_M_1.1V_AP";
508 regulator-min-microvolt = <800000>;
509 regulator-max-microvolt = <1350000>;
510 regulator-always-on;
514 regulator-name = "VDD_G3D_M_0.95V_AP";
515 regulator-min-microvolt = <950000>;
516 regulator-max-microvolt = <950000>;
517 regulator-always-on;
518 regulator-state-mem {
519 regulator-off-in-suspend;
524 regulator-name = "VDDQ_M1_LDO_1.2V_AP";
525 regulator-min-microvolt = <1200000>;
526 regulator-max-microvolt = <1200000>;
527 regulator-always-on;
528 regulator-state-mem {
529 regulator-off-in-suspend;
534 regulator-name = "VDDQ_M2_LDO_1.2V_AP";
535 regulator-min-microvolt = <1200000>;
536 regulator-max-microvolt = <1200000>;
537 regulator-always-on;
538 regulator-state-mem {
539 regulator-off-in-suspend;
544 regulator-name = "VDDQ_EFUSE";
545 regulator-min-microvolt = <1400000>;
546 regulator-max-microvolt = <3400000>;
547 regulator-always-on;
551 regulator-name = "V_TFLASH_2.8V_AP";
552 regulator-min-microvolt = <2800000>;
553 regulator-max-microvolt = <2800000>;
557 regulator-name = "V_CODEC_1.8V_AP";
558 regulator-min-microvolt = <1800000>;
559 regulator-max-microvolt = <1800000>;
563 regulator-name = "VDDA_1.8V_COMP";
564 regulator-min-microvolt = <1800000>;
565 regulator-max-microvolt = <1800000>;
566 regulator-always-on;
570 regulator-name = "VCC_2.8V_AP";
571 regulator-min-microvolt = <2800000>;
572 regulator-max-microvolt = <2800000>;
573 regulator-always-on;
577 regulator-name = "VT_CAM_1.8V";
578 regulator-min-microvolt = <1800000>;
579 regulator-max-microvolt = <1800000>;
583 regulator-name = "CAM_IO_1.8V_AP";
584 regulator-min-microvolt = <1800000>;
585 regulator-max-microvolt = <1800000>;
589 regulator-name = "CAM_SEN_CORE_1.05V_AP";
590 regulator-min-microvolt = <1050000>;
591 regulator-max-microvolt = <1050000>;
595 regulator-name = "VT_CAM_1.2V";
596 regulator-min-microvolt = <1200000>;
597 regulator-max-microvolt = <1200000>;
601 regulator-name = "UNUSED_LDO25";
602 regulator-min-microvolt = <2800000>;
603 regulator-max-microvolt = <2800000>;
607 regulator-name = "CAM_AF_2.8V_AP";
608 regulator-min-microvolt = <2800000>;
609 regulator-max-microvolt = <2800000>;
613 regulator-name = "VCC_3.0V_LCD_AP";
614 regulator-min-microvolt = <3000000>;
615 regulator-max-microvolt = <3000000>;
619 regulator-name = "VCC_1.8V_LCD_AP";
620 regulator-min-microvolt = <1800000>;
621 regulator-max-microvolt = <1800000>;
625 regulator-name = "VT_CAM_2.8V";
626 regulator-min-microvolt = <3000000>;
627 regulator-max-microvolt = <3000000>;
631 regulator-name = "TSP_AVDD_3.3V_AP";
632 regulator-min-microvolt = <3300000>;
633 regulator-max-microvolt = <3300000>;
644 regulator-name = "VTOUCH_1.8V_AP";
645 regulator-min-microvolt = <1800000>;
646 regulator-max-microvolt = <1800000>;
650 regulator-name = "VTOUCH_LED_3.3V";
651 regulator-min-microvolt = <2500000>;
652 regulator-max-microvolt = <3300000>;
653 regulator-ramp-delay = <12500>;
657 regulator-name = "VCC_1.8V_MHL_AP";
658 regulator-min-microvolt = <1000000>;
659 regulator-max-microvolt = <2100000>;
663 regulator-name = "OIS_VM_2.8V";
664 regulator-min-microvolt = <1800000>;
665 regulator-max-microvolt = <2800000>;
669 regulator-name = "VSIL_1.0V";
670 regulator-min-microvolt = <1000000>;
671 regulator-max-microvolt = <1000000>;
675 regulator-name = "VF_1.8V";
676 regulator-min-microvolt = <1800000>;
677 regulator-max-microvolt = <1800000>;
688 regulator-name = "V_HRM_1.8V";
689 regulator-min-microvolt = <1800000>;
690 regulator-max-microvolt = <1800000>;
694 regulator-name = "V_HRM_3.3V";
695 regulator-min-microvolt = <3300000>;
696 regulator-max-microvolt = <3300000>;
700 regulator-name = "VDD_MIF_0.9V_AP";
701 regulator-min-microvolt = <600000>;
702 regulator-max-microvolt = <1500000>;
703 regulator-always-on;
704 regulator-state-mem {
705 regulator-off-in-suspend;
710 regulator-name = "VDD_EGL_1.0V_AP";
711 regulator-min-microvolt = <900000>;
712 regulator-max-microvolt = <1300000>;
713 regulator-always-on;
714 regulator-state-mem {
715 regulator-off-in-suspend;
720 regulator-name = "VDD_KFC_1.0V_AP";
721 regulator-min-microvolt = <800000>;
722 regulator-max-microvolt = <1200000>;
723 regulator-always-on;
724 regulator-state-mem {
725 regulator-off-in-suspend;
730 regulator-name = "VDD_INT_0.95V_AP";
731 regulator-min-microvolt = <600000>;
732 regulator-max-microvolt = <1500000>;
733 regulator-always-on;
734 regulator-state-mem {
735 regulator-off-in-suspend;
740 regulator-name = "VDD_DISP_CAM0_0.9V_AP";
741 regulator-min-microvolt = <600000>;
742 regulator-max-microvolt = <1500000>;
743 regulator-always-on;
744 regulator-state-mem {
745 regulator-off-in-suspend;
750 regulator-name = "VDD_G3D_0.9V_AP";
751 regulator-min-microvolt = <600000>;
752 regulator-max-microvolt = <1500000>;
753 regulator-always-on;
754 regulator-state-mem {
755 regulator-off-in-suspend;
760 regulator-name = "VDD_MEM1_1.2V_AP";
761 regulator-min-microvolt = <1200000>;
762 regulator-max-microvolt = <1200000>;
763 regulator-always-on;
767 regulator-name = "VDD_LLDO_1.35V_AP";
768 regulator-min-microvolt = <1350000>;
769 regulator-max-microvolt = <3300000>;
770 regulator-always-on;
774 regulator-name = "VDD_MLDO_2.0V_AP";
775 regulator-min-microvolt = <1350000>;
776 regulator-max-microvolt = <3300000>;
777 regulator-always-on;
781 regulator-name = "vdd_mem2";
782 regulator-min-microvolt = <550000>;
783 regulator-max-microvolt = <1500000>;
784 regulator-always-on;
794 compatible = "samsung,s3fwrn5-i2c";
796 interrupt-parent = <&gpa1>;
798 en-gpios = <&gpf1 4 GPIO_ACTIVE_LOW>;
799 wake-gpios = <&gpj0 2 GPIO_ACTIVE_HIGH>;
809 interrupt-parent = <&gpa1>;
811 avdd-supply = <&ldo30_reg>;
812 vdd-supply = <&ldo31_reg>;
818 clock-frequency = <1000000>;
823 cvcc10-supply = <&ldo36_reg>;
824 iovcc18-supply = <&ldo34_reg>;
825 interrupt-parent = <&gpf0>;
827 reset-gpios = <&gpv7 0 GPIO_ACTIVE_LOW>;
829 clock-names = "xtal";
832 #address-cells = <1>;
833 #size-cells = <0>;
838 remote-endpoint = <&hdmi_to_mhl>;
845 remote-endpoint = <&musb_con_to_mhl>;
857 interrupt-parent = <&gpa1>;
862 compatible = "maxim,max77843-muic";
865 compatible = "samsung,usb-connector-11pin",
866 "usb-b-connector";
867 label = "micro-USB";
871 #address-cells = <1>;
872 #size-cells = <0>;
888 remote-endpoint = <&mhl_to_musb_con>;
897 remote-endpoint = <&usb_to_muic>;
904 compatible = "maxim,max77843-regulator";
906 regulator-name = "SAFEOUT1";
907 regulator-min-microvolt = <3300000>;
908 regulator-max-microvolt = <4950000>;
912 regulator-name = "SAFEOUT2";
913 regulator-min-microvolt = <3300000>;
914 regulator-max-microvolt = <4950000>;
918 regulator-name = "CHARGER";
919 regulator-min-microamp = <100000>;
920 regulator-max-microamp = <3150000>;
924 haptic: motor-driver {
925 compatible = "maxim,max77843-haptic";
926 haptic-supply = <&ldo38_reg>;
928 pwm-names = "haptic";
942 assigned-clocks = <&i2s1 CLK_I2S_RCLK_SRC>;
943 assigned-clock-parents = <&cmu_peric CLK_SCLK_I2S1>;
949 mmc-hs200-1_8v;
950 mmc-hs400-1_8v;
951 cap-mmc-highspeed;
952 non-removable;
953 card-detect-delay = <200>;
954 samsung,dw-mshc-ciu-div = <3>;
955 samsung,dw-mshc-sdr-timing = <0 4>;
956 samsung,dw-mshc-ddr-timing = <0 2>;
957 samsung,dw-mshc-hs400-timing = <0 3>;
958 samsung,read-strobe-delay = <90>;
959 fifo-depth = <0x80>;
960 pinctrl-names = "default";
961 pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_qrdy &sd0_bus1 &sd0_bus4
963 bus-width = <8>;
964 assigned-clocks = <&cmu_top CLK_SCLK_MMC0_FSYS>;
965 assigned-clock-rates = <800000000>;
970 cap-sd-highspeed;
971 disable-wp;
972 cd-gpios = <&gpa2 4 GPIO_ACTIVE_LOW>;
973 card-detect-delay = <200>;
974 samsung,dw-mshc-ciu-div = <3>;
975 samsung,dw-mshc-sdr-timing = <0 4>;
976 samsung,dw-mshc-ddr-timing = <0 2>;
977 fifo-depth = <0x80>;
978 pinctrl-names = "default";
979 pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus1 &sd2_bus4>;
980 bus-width = <4>;
985 pinctrl-names = "default";
986 pinctrl-0 = <&pcie_bus &pcie_wlanen>;
987 vdd10-supply = <&ldo6_reg>;
988 vdd18-supply = <&ldo7_reg>;
989 assigned-clocks = <&cmu_fsys CLK_MOUT_SCLK_PCIE_100_USER>,
991 assigned-clock-parents = <&cmu_top CLK_SCLK_PCIE_100_FSYS>,
993 assigned-clock-rates = <0>, <100000000>;
994 interrupt-map-mask = <0 0 0 0>;
995 interrupt-map = <0 0 0 0 &gic GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>;
1005 ppmu_event0_d0_general: ppmu-event0-d0-general {
1006 event-name = "ppmu-event0-d0-general";
1014 ppmu_event0_d1_general: ppmu-event0-d1-general {
1015 event-name = "ppmu-event0-d1-general";
1021 pinctrl-names = "default";
1022 pinctrl-0 = <&initial_alive>;
1024 initial_alive: initial-state {
1025 PIN_IN(gpa0-0, DOWN, FAST_SR1);
1026 PIN_IN(gpa0-1, NONE, FAST_SR1);
1027 PIN_IN(gpa0-2, DOWN, FAST_SR1);
1028 PIN_IN(gpa0-3, NONE, FAST_SR1);
1029 PIN_IN(gpa0-4, NONE, FAST_SR1);
1030 PIN_IN(gpa0-5, DOWN, FAST_SR1);
1031 PIN_IN(gpa0-6, NONE, FAST_SR1);
1032 PIN_IN(gpa0-7, NONE, FAST_SR1);
1034 PIN_IN(gpa1-0, UP, FAST_SR1);
1035 PIN_IN(gpa1-1, UP, FAST_SR1);
1036 PIN_IN(gpa1-2, NONE, FAST_SR1);
1037 PIN_IN(gpa1-3, DOWN, FAST_SR1);
1038 PIN_IN(gpa1-4, DOWN, FAST_SR1);
1039 PIN_IN(gpa1-5, NONE, FAST_SR1);
1040 PIN_IN(gpa1-6, NONE, FAST_SR1);
1041 PIN_IN(gpa1-7, NONE, FAST_SR1);
1043 PIN_IN(gpa2-0, NONE, FAST_SR1);
1044 PIN_IN(gpa2-1, NONE, FAST_SR1);
1045 PIN_IN(gpa2-2, NONE, FAST_SR1);
1046 PIN_IN(gpa2-3, DOWN, FAST_SR1);
1047 PIN_IN(gpa2-4, NONE, FAST_SR1);
1048 PIN_IN(gpa2-5, DOWN, FAST_SR1);
1049 PIN_IN(gpa2-6, DOWN, FAST_SR1);
1050 PIN_IN(gpa2-7, NONE, FAST_SR1);
1052 PIN_IN(gpa3-0, DOWN, FAST_SR1);
1053 PIN_IN(gpa3-1, DOWN, FAST_SR1);
1054 PIN_IN(gpa3-2, NONE, FAST_SR1);
1055 PIN_IN(gpa3-3, DOWN, FAST_SR1);
1056 PIN_IN(gpa3-4, NONE, FAST_SR1);
1057 PIN_IN(gpa3-5, DOWN, FAST_SR1);
1058 PIN_IN(gpa3-6, DOWN, FAST_SR1);
1059 PIN_IN(gpa3-7, DOWN, FAST_SR1);
1061 PIN_IN(gpf1-0, NONE, FAST_SR1);
1062 PIN_IN(gpf1-1, NONE, FAST_SR1);
1063 PIN_IN(gpf1-2, DOWN, FAST_SR1);
1064 PIN_IN(gpf1-4, UP, FAST_SR1);
1065 PIN_OT(gpf1-5, NONE, FAST_SR1);
1066 PIN_IN(gpf1-6, DOWN, FAST_SR1);
1067 PIN_IN(gpf1-7, DOWN, FAST_SR1);
1069 PIN_IN(gpf2-0, DOWN, FAST_SR1);
1070 PIN_IN(gpf2-1, DOWN, FAST_SR1);
1071 PIN_IN(gpf2-2, DOWN, FAST_SR1);
1072 PIN_IN(gpf2-3, DOWN, FAST_SR1);
1074 PIN_IN(gpf3-0, DOWN, FAST_SR1);
1075 PIN_IN(gpf3-1, DOWN, FAST_SR1);
1076 PIN_IN(gpf3-2, NONE, FAST_SR1);
1077 PIN_IN(gpf3-3, DOWN, FAST_SR1);
1079 PIN_IN(gpf4-0, DOWN, FAST_SR1);
1080 PIN_IN(gpf4-1, DOWN, FAST_SR1);
1081 PIN_IN(gpf4-2, DOWN, FAST_SR1);
1082 PIN_IN(gpf4-3, DOWN, FAST_SR1);
1083 PIN_IN(gpf4-4, DOWN, FAST_SR1);
1084 PIN_IN(gpf4-5, DOWN, FAST_SR1);
1085 PIN_IN(gpf4-6, DOWN, FAST_SR1);
1086 PIN_IN(gpf4-7, DOWN, FAST_SR1);
1088 PIN_IN(gpf5-0, DOWN, FAST_SR1);
1089 PIN_IN(gpf5-1, DOWN, FAST_SR1);
1090 PIN_IN(gpf5-2, DOWN, FAST_SR1);
1091 PIN_IN(gpf5-3, DOWN, FAST_SR1);
1092 PIN_OT(gpf5-4, NONE, FAST_SR1);
1093 PIN_IN(gpf5-5, DOWN, FAST_SR1);
1094 PIN_IN(gpf5-6, DOWN, FAST_SR1);
1095 PIN_IN(gpf5-7, DOWN, FAST_SR1);
1098 te_irq: te-irq-pins {
1099 samsung,pins = "gpf1-3";
1100 samsung,pin-function = <0xf>;
1105 pinctrl-names = "default";
1106 pinctrl-0 = <&initial_cpif>;
1108 initial_cpif: initial-state {
1109 PIN_IN(gpv6-0, DOWN, FAST_SR1);
1110 PIN_IN(gpv6-1, DOWN, FAST_SR1);
1115 pinctrl-names = "default";
1116 pinctrl-0 = <&initial_ese>;
1118 pcie_wlanen: pcie-wlanen-pins {
1119 samsung,pins = "gpj2-0";
1120 samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
1121 samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
1122 samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
1125 initial_ese: initial-state {
1126 PIN_IN(gpj2-1, DOWN, FAST_SR1);
1127 PIN_IN(gpj2-2, DOWN, FAST_SR1);
1132 pinctrl-names = "default";
1133 pinctrl-0 = <&initial_fsys>;
1135 initial_fsys: initial-state {
1136 PIN_IN(gpr3-0, NONE, FAST_SR1);
1137 PIN_IN(gpr3-1, DOWN, FAST_SR1);
1138 PIN_IN(gpr3-2, DOWN, FAST_SR1);
1139 PIN_IN(gpr3-3, DOWN, FAST_SR1);
1140 PIN_IN(gpr3-7, NONE, FAST_SR1);
1145 pinctrl-names = "default";
1146 pinctrl-0 = <&initial_imem>;
1148 initial_imem: initial-state {
1149 PIN_IN(gpf0-0, UP, FAST_SR1);
1150 PIN_IN(gpf0-1, UP, FAST_SR1);
1151 PIN_IN(gpf0-2, DOWN, FAST_SR1);
1152 PIN_IN(gpf0-3, UP, FAST_SR1);
1153 PIN_IN(gpf0-4, DOWN, FAST_SR1);
1154 PIN_IN(gpf0-5, NONE, FAST_SR1);
1155 PIN_IN(gpf0-6, DOWN, FAST_SR1);
1156 PIN_IN(gpf0-7, UP, FAST_SR1);
1161 pinctrl-names = "default";
1162 pinctrl-0 = <&initial_nfc>;
1164 initial_nfc: initial-state {
1165 PIN_IN(gpj0-2, DOWN, FAST_SR1);
1170 pinctrl-names = "default";
1171 pinctrl-0 = <&initial_peric>;
1173 initial_peric: initial-state {
1174 PIN_IN(gpv7-0, DOWN, FAST_SR1);
1175 PIN_IN(gpv7-1, DOWN, FAST_SR1);
1176 PIN_IN(gpv7-2, NONE, FAST_SR1);
1177 PIN_IN(gpv7-3, DOWN, FAST_SR1);
1178 PIN_IN(gpv7-4, DOWN, FAST_SR1);
1179 PIN_IN(gpv7-5, DOWN, FAST_SR1);
1181 PIN_IN(gpb0-4, DOWN, FAST_SR1);
1183 PIN_IN(gpc0-2, DOWN, FAST_SR1);
1184 PIN_IN(gpc0-5, DOWN, FAST_SR1);
1185 PIN_IN(gpc0-7, DOWN, FAST_SR1);
1187 PIN_IN(gpc1-1, DOWN, FAST_SR1);
1189 PIN_IN(gpc3-4, NONE, FAST_SR1);
1190 PIN_IN(gpc3-5, NONE, FAST_SR1);
1191 PIN_IN(gpc3-6, NONE, FAST_SR1);
1192 PIN_IN(gpc3-7, NONE, FAST_SR1);
1194 PIN_OT(gpg0-0, NONE, FAST_SR1);
1195 PIN_F2(gpg0-1, DOWN, FAST_SR1);
1197 PIN_IN(gpd2-5, DOWN, FAST_SR1);
1199 PIN_IN(gpd4-0, NONE, FAST_SR1);
1200 PIN_IN(gpd4-1, DOWN, FAST_SR1);
1201 PIN_IN(gpd4-2, DOWN, FAST_SR1);
1202 PIN_IN(gpd4-3, DOWN, FAST_SR1);
1203 PIN_IN(gpd4-4, DOWN, FAST_SR1);
1205 PIN_IN(gpd6-3, DOWN, FAST_SR1);
1207 PIN_IN(gpd8-1, UP, FAST_SR1);
1209 PIN_IN(gpg1-0, DOWN, FAST_SR1);
1210 PIN_IN(gpg1-1, DOWN, FAST_SR1);
1211 PIN_IN(gpg1-2, DOWN, FAST_SR1);
1212 PIN_IN(gpg1-3, DOWN, FAST_SR1);
1213 PIN_IN(gpg1-4, DOWN, FAST_SR1);
1215 PIN_IN(gpg2-0, DOWN, FAST_SR1);
1216 PIN_IN(gpg2-1, DOWN, FAST_SR1);
1218 PIN_IN(gpg3-0, DOWN, FAST_SR1);
1219 PIN_IN(gpg3-1, DOWN, FAST_SR1);
1220 PIN_IN(gpg3-5, DOWN, FAST_SR1);
1225 pinctrl-names = "default";
1226 pinctrl-0 = <&initial_touch>;
1228 initial_touch: initial-state {
1229 PIN_IN(gpj1-2, DOWN, FAST_SR1);
1234 pinctrl-0 = <&pwm0_out>;
1235 pinctrl-names = "default";
1244 assigned-clocks = <&pmu_system_controller 0>;
1245 assigned-clock-parents = <&xxti>;
1256 compatible = "brcm,bcm43438-bt";
1257 max-speed = <3000000>;
1258 shutdown-gpios = <&gpd4 0 GPIO_ACTIVE_HIGH>;
1259 device-wakeup-gpios = <&gpr3 7 GPIO_ACTIVE_HIGH>;
1260 host-wakeup-gpios = <&gpa2 2 GPIO_ACTIVE_HIGH>;
1262 clock-names = "extclk";
1267 cs-gpios = <&gpd6 3 GPIO_ACTIVE_HIGH>;
1270 wm5110: audio-codec@0 {
1273 spi-max-frequency = <20000000>;
1274 interrupt-parent = <&gpa0>;
1278 clock-names = "mclk1", "mclk2";
1280 gpio-controller;
1281 #gpio-cells = <2>;
1283 wlf,micd-detect-debounce = <300>;
1284 wlf,micd-bias-start-time = <0x1>;
1285 wlf,micd-rate = <0x7>;
1286 wlf,micd-dbtime = <0x1>;
1287 wlf,micd-force-micbias;
1288 wlf,micd-configs = <0x0 1 0>;
1289 wlf,hpdet-channel = <1>;
1297 AVDD-supply = <&ldo18_reg>;
1298 DBVDD1-supply = <&ldo18_reg>;
1299 CPVDD-supply = <&ldo18_reg>;
1300 DBVDD2-supply = <&ldo18_reg>;
1301 DBVDD3-supply = <&ldo18_reg>;
1303 controller-data {
1304 samsung,spi-feedback-delay = <0>;
1311 no-cs-readback;
1314 compatible = "ir-spi-led";
1316 spi-max-frequency = <5000000>;
1317 power-supply = <&irda_regulator>;
1318 duty-cycle = <60>;
1319 led-active-low;
1321 controller-data {
1322 samsung,spi-feedback-delay = <0>;
1328 clock-frequency = <24000000>;
1332 vtmu-supply = <&ldo3_reg>;
1337 vtmu-supply = <&ldo3_reg>;
1342 vtmu-supply = <&ldo3_reg>;
1347 vdd33-supply = <&ldo10_reg>;
1348 vdd10-supply = <&ldo6_reg>;
1357 vbus-supply = <&safeout1_reg>;
1362 remote-endpoint = <&muic_to_usb>;
1368 clock-frequency = <24000000>;