Lines Matching +full:realtek +full:- +full:mdio
1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
6 /dts-v1/;
8 #include "meson-gxbb.dtsi"
9 #include <dt-bindings/gpio/gpio.h>
10 #include <dt-bindings/sound/meson-aiu.h>
13 compatible = "friendlyarm,nanopi-k2", "amlogic,meson-gxbb";
22 stdout-path = "serial0:115200n8";
31 compatible = "gpio-leds";
33 led-stat {
34 label = "nanopi-k2:blue:stat";
36 default-state = "on";
37 panic-indicator;
41 vdd_5v: regulator-vdd-5v {
42 compatible = "regulator-fixed";
43 regulator-name = "VDD_5V";
44 regulator-min-microvolt = <5000000>;
45 regulator-max-microvolt = <5000000>;
48 vddio_ao18: regulator-vddio-ao18 {
49 compatible = "regulator-fixed";
50 regulator-name = "VDDIO_AO18";
51 regulator-min-microvolt = <1800000>;
52 regulator-max-microvolt = <1800000>;
55 vddio_ao3v3: regulator-vddio-ao3v3 {
56 compatible = "regulator-fixed";
57 regulator-name = "VDDIO_AO3.3V";
58 regulator-min-microvolt = <3300000>;
59 regulator-max-microvolt = <3300000>;
62 vddio_tf: regulator-vddio-tf {
63 compatible = "regulator-gpio";
65 regulator-name = "VDDIO_TF";
66 regulator-min-microvolt = <1800000>;
67 regulator-max-microvolt = <3300000>;
70 gpios-states = <0>;
75 regulator-settling-time-up-us = <100>;
76 regulator-settling-time-down-us = <5000>;
79 wifi_32k: wifi-32k {
80 compatible = "pwm-clock";
81 #clock-cells = <0>;
82 clock-frequency = <32768>;
86 sdio_pwrseq: sdio-pwrseq {
87 compatible = "mmc-pwrseq-simple";
88 reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
90 clock-names = "ext_clock";
93 vcc1v8: regulator-vcc1v8 {
94 compatible = "regulator-fixed";
95 regulator-name = "VCC1.8V";
96 regulator-min-microvolt = <1800000>;
97 regulator-max-microvolt = <1800000>;
100 vcc3v3: regulator-vcc3v3 {
101 compatible = "regulator-fixed";
102 regulator-name = "VCC3.3V";
103 regulator-min-microvolt = <3300000>;
104 regulator-max-microvolt = <3300000>;
107 emmc_pwrseq: emmc-pwrseq {
108 compatible = "mmc-pwrseq-emmc";
109 reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
113 cvbs-connector {
114 compatible = "composite-video-connector";
119 remote-endpoint = <&cvbs_vdac_out>;
124 hdmi-connector {
125 compatible = "hdmi-connector";
130 remote-endpoint = <&hdmi_tx_tmds_out>;
136 compatible = "amlogic,gx-sound-card";
137 model = "NANOPI-K2";
138 assigned-clocks = <&clkc CLKID_MPLL0>,
141 assigned-clock-parents = <0>, <0>, <0>;
142 assigned-clock-rates = <294912000>,
147 dai-link-0 {
148 sound-dai = <&aiu AIU_CPU CPU_I2S_FIFO>;
151 dai-link-1 {
152 sound-dai = <&aiu AIU_CPU CPU_I2S_ENCODER>;
153 dai-format = "i2s";
154 mclk-fs = <256>;
156 codec-0 {
157 sound-dai = <&aiu AIU_HDMI CTRL_I2S>;
161 dai-link-2 {
162 sound-dai = <&aiu AIU_HDMI CTRL_OUT>;
164 codec-0 {
165 sound-dai = <&hdmi_tx>;
177 pinctrl-0 = <&ao_cec_pins>;
178 pinctrl-names = "default";
179 hdmi-phandle = <&hdmi_tx>;
184 remote-endpoint = <&cvbs_connector_in>;
190 pinctrl-0 = <ð_rgmii_pins>;
191 pinctrl-names = "default";
193 phy-handle = <ð_phy0>;
194 phy-mode = "rgmii";
196 amlogic,tx-delay-ns = <2>;
198 mdio {
199 compatible = "snps,dwmac-mdio";
200 #address-cells = <1>;
201 #size-cells = <0>;
203 eth_phy0: ethernet-phy@0 {
204 /* Realtek RTL8211F (0x001cc916) */
207 reset-assert-us = <10000>;
208 reset-deassert-us = <80000>;
209 reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
211 interrupt-parent = <&gpio_intc>;
220 pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
221 pinctrl-names = "default";
226 remote-endpoint = <&hdmi_connector_in>;
232 pinctrl-0 = <&remote_input_ao_pins>;
233 pinctrl-names = "default";
237 gpio-line-names = "UART TX", "UART RX", "Power Control", "Power Key In",
247 gpio-line-names = /* Bank GPIOZ */
248 "Eth MDIO", "Eth MDC", "Eth RGMII RX Clk",
296 pinctrl-0 = <&pwm_e_pins>;
297 pinctrl-names = "default";
299 clock-names = "clkin0";
304 vref-supply = <&vddio_ao18>;
310 pinctrl-0 = <&sdio_pins>, <&sdio_irq_pins>;
311 pinctrl-1 = <&sdio_clk_gate_pins>;
312 pinctrl-names = "default", "clk-gate";
313 #address-cells = <1>;
314 #size-cells = <0>;
316 bus-width = <4>;
317 cap-sd-highspeed;
318 max-frequency = <50000000>;
320 non-removable;
321 disable-wp;
324 keep-power-in-suspend;
326 mmc-pwrseq = <&sdio_pwrseq>;
328 vmmc-supply = <&vddio_ao3v3>;
329 vqmmc-supply = <&vddio_ao18>;
332 compatible = "brcm,bcm4329-fmac";
340 pinctrl-0 = <&sdcard_pins>;
341 pinctrl-1 = <&sdcard_clk_gate_pins>;
342 pinctrl-names = "default", "clk-gate";
344 bus-width = <4>;
345 cap-sd-highspeed;
346 sd-uhs-sdr12;
347 sd-uhs-sdr25;
348 sd-uhs-sdr50;
349 sd-uhs-ddr50;
350 max-frequency = <100000000>;
351 disable-wp;
353 cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
355 vmmc-supply = <&vddio_ao3v3>;
356 vqmmc-supply = <&vddio_tf>;
362 pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
363 pinctrl-1 = <&emmc_clk_gate_pins>;
364 pinctrl-names = "default", "clk-gate";
366 bus-width = <8>;
367 max-frequency = <200000000>;
368 non-removable;
369 disable-wp;
370 cap-mmc-highspeed;
371 mmc-ddr-1_8v;
372 mmc-hs200-1_8v;
374 mmc-pwrseq = <&emmc_pwrseq>;
375 vmmc-supply = <&vcc3v3>;
376 vqmmc-supply = <&vcc1v8>;
382 pinctrl-0 = <&uart_ao_a_pins>;
383 pinctrl-names = "default";
389 pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
390 pinctrl-names = "default";
391 uart-has-rtscts;
394 compatible = "brcm,bcm43438-bt";
396 clock-names = "lpo";
397 vbat-supply = <&vddio_ao3v3>;
398 vddio-supply = <&vddio_ao18>;
399 host-wakeup-gpios = <&gpio GPIOX_21 GPIO_ACTIVE_HIGH>;
400 shutdown-gpios = <&gpio GPIOX_20 GPIO_ACTIVE_HIGH>;
404 /* 40-pin CON1 */
407 pinctrl-0 = <&uart_c_pins>;
408 pinctrl-names = "default";
413 phy-supply = <&vdd_5v>;