Lines Matching +full:edt +full:- +full:ft5x06
1 // SPDX-License-Identifier: GPL-2.0 OR X11
5 #include <dt-bindings/gpio/gpio.h>
6 #include <dt-bindings/input/input.h>
10 stdout-path = &uart2;
19 compatible = "simple-bus";
20 #address-cells = <1>;
21 #size-cells = <0>;
24 compatible = "regulator-fixed";
26 regulator-name = "2P5V";
27 regulator-min-microvolt = <2500000>;
28 regulator-max-microvolt = <2500000>;
29 regulator-always-on;
33 compatible = "regulator-fixed";
35 regulator-name = "3P3V";
36 regulator-min-microvolt = <3300000>;
37 regulator-max-microvolt = <3300000>;
38 regulator-always-on;
42 compatible = "regulator-fixed";
44 regulator-name = "usb_otg_vbus";
45 regulator-min-microvolt = <5000000>;
46 regulator-max-microvolt = <5000000>;
48 enable-active-high;
52 compatible = "regulator-fixed";
54 pinctrl-names = "default";
55 pinctrl-0 = <&pinctrl_wlan_vmmc>;
56 regulator-name = "reg_wlan_vmmc";
57 regulator-min-microvolt = <1800000>;
58 regulator-max-microvolt = <1800000>;
60 startup-delay-us = <70000>;
61 enable-active-high;
65 gpio-keys {
66 compatible = "gpio-keys";
67 pinctrl-names = "default";
68 pinctrl-0 = <&pinctrl_gpio_keys>;
84 compatible = "gpio-leds";
85 pinctrl-names = "default";
86 pinctrl-0 = <&pinctrl_leds>;
88 j14-pin1 {
90 retain-state-suspended;
91 default-state = "off";
94 j14-pin3 {
96 retain-state-suspended;
97 default-state = "off";
100 j14-pins8-9 {
102 retain-state-suspended;
103 default-state = "off";
106 j46-pin2 {
108 retain-state-suspended;
109 default-state = "off";
112 j46-pin3 {
114 retain-state-suspended;
115 default-state = "off";
119 backlight-lcd {
120 compatible = "pwm-backlight";
122 brightness-levels = <0 4 8 16 32 64 128 255>;
123 default-brightness-level = <7>;
124 power-supply = <®_3p3v>;
128 backlight_lvds0: backlight-lvds0 {
129 compatible = "pwm-backlight";
131 brightness-levels = <0 4 8 16 32 64 128 255>;
132 default-brightness-level = <7>;
133 power-supply = <®_3p3v>;
137 panel-lvds0 {
143 remote-endpoint = <&lvds0_out>;
149 compatible = "fsl,imx6dl-nit6xlite-sgtl5000",
150 "fsl,imx-audio-sgtl5000";
151 model = "imx6dl-nit6xlite-sgtl5000";
152 ssi-controller = <&ssi1>;
153 audio-codec = <&codec>;
154 audio-routing =
158 mux-int-port = <1>;
159 mux-ext-port = <3>;
164 pinctrl-names = "default";
165 pinctrl-0 = <&pinctrl_audmux>;
170 assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
172 assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
177 cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
178 pinctrl-names = "default";
179 pinctrl-0 = <&pinctrl_ecspi1>;
184 spi-max-frequency = <20000000>;
190 pinctrl-names = "default";
191 pinctrl-0 = <&pinctrl_enet>;
192 phy-mode = "rgmii";
193 phy-handle = <ðphy>;
194 phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
195 /delete-property/ interrupts;
196 interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
198 fsl,err006687-workaround-present;
202 #address-cells = <1>;
203 #size-cells = <0>;
205 ethphy: ethernet-phy {
206 compatible = "ethernet-phy-ieee802.3-c22";
207 txen-skew-ps = <0>;
208 txc-skew-ps = <3000>;
209 rxdv-skew-ps = <0>;
210 rxc-skew-ps = <3000>;
211 rxd0-skew-ps = <0>;
212 rxd1-skew-ps = <0>;
213 rxd2-skew-ps = <0>;
214 rxd3-skew-ps = <0>;
215 txd0-skew-ps = <0>;
216 txd1-skew-ps = <0>;
217 txd2-skew-ps = <0>;
218 txd3-skew-ps = <0>;
224 ddc-i2c-bus = <&i2c2>;
229 clock-frequency = <100000>;
230 pinctrl-names = "default";
231 pinctrl-0 = <&pinctrl_i2c1>;
236 pinctrl-names = "default";
237 pinctrl-0 = <&pinctrl_sgtl5000>;
240 VDDA-supply = <®_2p5v>;
241 VDDIO-supply = <®_3p3v>;
246 clock-frequency = <100000>;
247 pinctrl-names = "default";
248 pinctrl-0 = <&pinctrl_i2c2>;
253 clock-frequency = <100000>;
254 pinctrl-names = "default";
255 pinctrl-0 = <&pinctrl_i2c3>;
261 interrupt-parent = <&gpio1>;
263 wakeup-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
267 compatible = "edt,edt-ft5x06";
269 interrupt-parent = <&gpio1>;
271 wakeup-source;
276 pinctrl-names = "default";
277 pinctrl-0 = <&pinctrl_rtc>;
279 interrupts-extended = <&gpio2 26 IRQ_TYPE_LEVEL_LOW>;
284 pinctrl-names = "default";
285 pinctrl-0 = <&pinctrl_j10>;
286 pinctrl-1 = <&pinctrl_j28>;
288 imx6dl-nit6xlite {
331 pinctrl_gpio_keys: gpio-keysgrp {
414 pinctrl_wlan_vmmc: wlan-vmmcgrp {
493 lvds-channel@0 {
500 remote-endpoint = <&panel_in_lvds0>;
511 #pwm-cells = <2>;
512 pinctrl-names = "default";
513 pinctrl-0 = <&pinctrl_pwm1>;
518 pinctrl-names = "default";
519 pinctrl-0 = <&pinctrl_pwm3>;
524 #pwm-cells = <2>;
525 pinctrl-names = "default";
526 pinctrl-0 = <&pinctrl_pwm4>;
535 pinctrl-names = "default";
536 pinctrl-0 = <&pinctrl_uart1>;
541 pinctrl-names = "default";
542 pinctrl-0 = <&pinctrl_uart2>;
547 pinctrl-names = "default";
548 pinctrl-0 = <&pinctrl_uart3>;
549 uart-has-rtscts;
558 vbus-supply = <®_usb_otg_vbus>;
559 pinctrl-names = "default";
560 pinctrl-0 = <&pinctrl_usbotg>;
561 disable-over-current;
566 pinctrl-names = "default";
567 pinctrl-0 = <&pinctrl_usdhc2>;
568 bus-width = <4>;
569 non-removable;
570 vmmc-supply = <®_3p3v>;
571 vqmmc-supply = <®_wlan_vmmc>;
572 cap-power-off-card;
573 keep-power-in-suspend;
578 pinctrl-names = "default";
579 pinctrl-0 = <&pinctrl_usdhc3>;
580 cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
581 vmmc-supply = <®_3p3v>;