Lines Matching +full:io +full:- +full:channel +full:- +full:names
1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
6 /dts-v1/;
8 #include "imx6qdl-prti6q.dtsi"
9 #include <dt-bindings/display/sdtv-standards.h>
10 #include <dt-bindings/input/input.h>
11 #include <dt-bindings/leds/common.h>
12 #include <dt-bindings/sound/fsl-imx-audmux.h>
23 backlight_lcd: backlight-lcd {
24 compatible = "pwm-backlight";
26 brightness-levels = <0 20 81 248 1000>;
27 default-brightness-level = <20>;
28 num-interpolated-steps = <21>;
29 power-supply = <®_bl_12v0>;
33 compatible = "fsl,imx-parallel-display";
34 pinctrl-0 = <&pinctrl_ipu1_disp>;
35 pinctrl-names = "default";
36 #address-cells = <1>;
37 #size-cells = <0>;
43 remote-endpoint = <&ipu1_di0_disp0>;
51 remote-endpoint = <&panel_in>;
56 iio-hwmon {
57 compatible = "iio-hwmon";
58 io-channels = <&vdiv_vaccu>;
62 compatible = "gpio-keys";
65 key-esc {
71 key-up {
77 key-down {
83 key-enter {
89 key-cycle {
95 key-f1 {
101 key-f2 {
107 key-f3 {
113 key-f4 {
119 key-f5 {
125 key-f6 {
131 key-f7 {
137 key-f8 {
143 key-f9 {
149 key-f10 {
157 compatible = "gpio-leds";
158 pinctrl-names = "default";
159 pinctrl-0 = <&pinctrl_leds>;
161 led-debug0 {
164 linux,default-trigger = "heartbeat";
169 compatible = "innolux,g070y2-t02";
171 power-supply = <®_3v3>;
175 remote-endpoint = <&display_out>;
181 compatible = "composite-video-connector";
183 sdtv-standards = <SDTV_STD_PAL_B>;
187 remote-endpoint = <&tvp5150_comp0_in>;
192 reg_bl_12v0: regulator-bl-12v0 {
193 compatible = "regulator-fixed";
194 pinctrl-names = "default";
195 pinctrl-0 = <&pinctrl_reg_bl_12v0>;
196 regulator-name = "bl-12v0";
197 regulator-min-microvolt = <12000000>;
198 regulator-max-microvolt = <12000000>;
200 enable-active-high;
203 reg_3v3: regulator-3v3 {
204 compatible = "regulator-fixed";
205 regulator-name = "3v3";
206 regulator-min-microvolt = <3300000>;
207 regulator-max-microvolt = <3300000>;
210 reg_1v8: regulator-1v8 {
211 compatible = "regulator-fixed";
212 regulator-name = "1v8";
213 regulator-min-microvolt = <1800000>;
214 regulator-max-microvolt = <1800000>;
218 compatible = "simple-audio-card";
219 simple-audio-card,name = "prti6q-sgtl5000";
220 simple-audio-card,format = "i2s";
221 simple-audio-card,widgets =
226 simple-audio-card,routing =
232 simple-audio-card,cpu {
233 sound-dai = <&ssi1>;
234 system-clock-frequency = <0>;
237 simple-audio-card,codec {
238 sound-dai = <&sgtl5000>;
239 bitclock-master;
240 frame-master;
244 thermal-zones {
245 chassis-thermal {
246 polling-delay = <20000>;
247 polling-delay-passive = <0>;
248 thermal-sensors = <&tsens0>;
251 touch-thermal0 {
252 polling-delay = <20000>;
253 polling-delay-passive = <0>;
254 thermal-sensors = <&touch_temp0>;
257 touch-thermal1 {
258 polling-delay = <20000>;
259 polling-delay-passive = <0>;
260 thermal-sensors = <&touch_temp1>;
265 compatible = "resistive-adc-touch";
266 io-channels = <&adc_ts 1>, <&adc_ts 3>, <&adc_ts 4>,
268 io-channel-names = "y", "z1", "z2", "x";
269 touchscreen-min-pressure = <64687>;
270 touchscreen-inverted-x;
271 touchscreen-inverted-y;
272 touchscreen-x-plate-ohms = <300>;
273 touchscreen-y-plate-ohms = <800>;
276 touch_temp0: touch-temperature-sensor0 {
277 compatible = "generic-adc-thermal";
278 #thermal-sensor-cells = <0>;
279 io-channels = <&adc_ts 0>;
280 io-channel-names = "sensor-channel";
281 temperature-lookup-table = < (-40000) 736
285 touch_temp1: touch-temperature-sensor1 {
286 compatible = "generic-adc-thermal";
287 #thermal-sensor-cells = <0>;
288 io-channels = <&adc_ts 7>;
289 io-channel-names = "sensor-channel";
290 temperature-lookup-table = < (-40000) 826
294 vdiv_vaccu: voltage-divider-vaccu {
295 compatible = "voltage-divider";
296 io-channels = <&adc_ts 2>;
297 output-ohms = <2500>;
298 full-ohms = <64000>;
299 #io-channel-cells = <0>;
304 pinctrl-names = "default";
305 pinctrl-0 = <&pinctrl_audmux>;
308 mux-ssi1 {
309 fsl,audmux-port = <0>;
310 fsl,port-config = <
319 mux-pins3 {
320 fsl,audmux-port = <2>;
321 fsl,port-config = <
329 pinctrl-0 = <&pinctrl_can1 &pinctrl_can1phy>;
333 assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
334 assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
338 cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
339 pinctrl-names = "default";
340 pinctrl-0 = <&pinctrl_ecspi2>;
344 compatible = "ti,tsc2046e-adc";
346 pinctrl-0 = <&pinctrl_tsc>;
347 pinctrl-names = "default";
348 spi-max-frequency = <1000000>;
349 interrupts-extended = <&gpio3 20 IRQ_TYPE_LEVEL_LOW>;
350 #io-channel-cells = <1>;
352 #address-cells = <1>;
353 #size-cells = <0>;
355 channel@1 {
357 settling-time-us = <700>;
358 oversampling-ratio = <5>;
361 channel@3 {
363 settling-time-us = <700>;
364 oversampling-ratio = <5>;
367 channel@4 {
369 settling-time-us = <700>;
370 oversampling-ratio = <5>;
373 channel@5 {
375 settling-time-us = <700>;
376 oversampling-ratio = <5>;
382 sgtl5000: audio-codec@a {
385 pinctrl-names = "default";
386 pinctrl-0 = <&pinctrl_codec>;
387 #sound-dai-cells = <0>;
389 VDDA-supply = <®_3v3>;
390 VDDIO-supply = <®_3v3>;
391 VDDD-supply = <®_1v8>;
398 #address-cells = <1>;
399 #size-cells = <0>;
405 remote-endpoint = <&comp0_out>;
414 remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
426 tsens0: temperature-sensor@70 {
429 #thermal-sensor-cells = <0>;
435 interrupts-extended = <&gpio4 5 IRQ_TYPE_LEVEL_LOW>;
436 #gpio-cells = <2>;
437 gpio-controller;
442 pinctrl-names = "default";
443 pinctrl-0 = <&pinctrl_ipu1_csi0>;
448 remote-endpoint = <&display_in>;
452 remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>;
456 pinctrl-names = "default";
457 pinctrl-0 = <&pinctrl_pwm1>;