Lines Matching +full:num +full:- +full:interpolated +full:- +full:steps
1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
7 /dts-v1/;
8 #include <dt-bindings/display/sdtv-standards.h>
9 #include <dt-bindings/gpio/gpio.h>
10 #include <dt-bindings/input/input.h>
11 #include <dt-bindings/leds/common.h>
12 #include <dt-bindings/media/tvp5150.h>
13 #include <dt-bindings/sound/fsl-imx-audmux.h>
21 stdout-path = &uart4;
25 compatible = "pwm-backlight";
26 pinctrl-names = "default";
27 pinctrl-0 = <&pinctrl_backlight>;
29 brightness-levels = <0 16 64 255>;
30 num-interpolated-steps = <16>;
31 default-brightness-level = <1>;
32 power-supply = <®_3v3>;
33 enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
37 compatible = "composite-video-connector";
39 sdtv-standards = <SDTV_STD_PAL_B>;
43 remote-endpoint = <&tvp5150_comp0_in>;
48 gpio-keys {
49 compatible = "gpio-keys";
50 pinctrl-names = "default";
51 pinctrl-0 = <&pinctrl_gpiokeys>;
54 key-power {
58 wakeup-source;
61 key-f1 {
67 key-f2 {
73 key-f3 {
79 key-f4 {
85 key-f5 {
91 key-cycle {
97 key-esc {
103 key-up {
109 key-down {
115 key-ok {
121 key-f6 {
127 key-f7 {
133 key-f8 {
139 key-f9 {
145 key-f10 {
154 compatible = "gpio-leds";
155 pinctrl-names = "default";
156 pinctrl-0 = <&pinctrl_leds>;
158 led-0 {
162 linux,default-trigger = "heartbeat";
165 led-1 {
169 linux,default-trigger = "disk-activity";
172 led-2 {
176 default-state = "on";
183 power-supply = <®_3v3>;
187 remote-endpoint = <&lvds0_out>;
192 clk50m_phy: phy-clock {
193 compatible = "fixed-clock";
194 #clock-cells = <0>;
195 clock-frequency = <50000000>;
198 reg_1v8: regulator-1v8 {
199 compatible = "regulator-fixed";
200 regulator-name = "1v8";
201 regulator-min-microvolt = <1800000>;
202 regulator-max-microvolt = <1800000>;
205 reg_3v3: regulator-3v3 {
206 compatible = "regulator-fixed";
207 regulator-name = "3v3";
208 regulator-min-microvolt = <3300000>;
209 regulator-max-microvolt = <3300000>;
212 reg_h1_vbus: regulator-h1-vbus {
213 compatible = "regulator-fixed";
214 regulator-name = "h1-vbus";
215 regulator-min-microvolt = <5000000>;
216 regulator-max-microvolt = <5000000>;
218 enable-active-high;
221 reg_otg_vbus: regulator-otg-vbus {
222 compatible = "regulator-fixed";
223 regulator-name = "otg-vbus";
224 regulator-min-microvolt = <5000000>;
225 regulator-max-microvolt = <5000000>;
227 enable-active-high;
231 compatible = "simple-audio-card";
232 simple-audio-card,name = "prti6q-sgtl5000";
233 simple-audio-card,format = "i2s";
234 simple-audio-card,widgets =
239 simple-audio-card,routing =
245 simple-audio-card,cpu {
246 sound-dai = <&ssi1>;
247 system-clock-frequency = <0>;
250 simple-audio-card,codec {
251 sound-dai = <&codec>;
252 bitclock-master;
253 frame-master;
259 pinctrl-names = "default";
260 pinctrl-0 = <&pinctrl_audmux>;
263 mux-ssi1 {
264 fsl,audmux-port = <0>;
265 fsl,port-config = <
274 mux-pins3 {
275 fsl,audmux-port = <2>;
276 fsl,port-config = <
284 pinctrl-names = "default";
285 pinctrl-0 = <&pinctrl_can1>;
290 pinctrl-names = "default";
291 pinctrl-0 = <&pinctrl_can2>;
296 assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
297 assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
301 cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
302 pinctrl-names = "default";
303 pinctrl-0 = <&pinctrl_ecspi1>;
307 compatible = "jedec,spi-nor";
309 spi-max-frequency = <20000000>;
314 pinctrl-names = "default";
315 pinctrl-0 = <&pinctrl_enet>;
316 phy-mode = "rmii";
320 clock-names = "ipg", "ahb", "ptp";
321 phy-handle = <&rmii_phy>;
325 #address-cells = <1>;
326 #size-cells = <0>;
329 rmii_phy: ethernet-phy@0 {
331 interrupts-extended = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>;
332 reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
333 reset-assert-us = <10000>;
334 reset-deassert-us = <3000>;
340 gpio-line-names =
350 gpio-line-names =
359 gpio-line-names =
369 gpio-line-names =
378 gpio-line-names =
387 clock-frequency = <100000>;
388 pinctrl-names = "default";
389 pinctrl-0 = <&pinctrl_i2c1>;
392 codec: audio-codec@a {
395 #sound-dai-cells = <0>;
397 VDDA-supply = <®_3v3>;
398 VDDIO-supply = <®_3v3>;
399 VDDD-supply = <®_1v8>;
405 #address-cells = <1>;
406 #size-cells = <0>;
412 remote-endpoint = <&comp0_out>;
420 remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
428 pinctrl-names = "default";
429 pinctrl-0 = <&pinctrl_pca9539>;
430 interrupt-parent = <&gpio4>;
432 gpio-controller;
433 #gpio-cells = <2>;
440 clock-frequency = <100000>;
441 pinctrl-names = "default";
442 pinctrl-0 = <&pinctrl_i2c3>;
448 #address-cells = <1>;
449 #size-cells = <0>;
481 temperature-sensor@70 {
488 pinctrl-names = "default";
489 pinctrl-0 = <&pinctrl_ipu1_csi0>;
494 remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>;
500 lvds-channel@0 {
507 remote-endpoint = <&panel_in>;
518 pinctrl-names = "default";
519 pinctrl-0 = <&pinctrl_pwm1>;
524 #sound-dai-cells = <0>;
525 fsl,mode = "ac97-slave";
530 pinctrl-names = "default";
531 pinctrl-0 = <&pinctrl_uart1>;
536 pinctrl-names = "default";
537 pinctrl-0 = <&pinctrl_uart2>;
542 pinctrl-names = "default";
543 pinctrl-0 = <&pinctrl_uart3>;
548 pinctrl-names = "default";
549 pinctrl-0 = <&pinctrl_uart4>;
554 pinctrl-names = "default";
555 pinctrl-0 = <&pinctrl_uart5>;
560 vbus-supply = <®_h1_vbus>;
561 pinctrl-names = "default";
568 vbus-supply = <®_otg_vbus>;
569 pinctrl-names = "default";
570 pinctrl-0 = <&pinctrl_usbotg>;
573 disable-over-current;
578 pinctrl-names = "default";
579 pinctrl-0 = <&pinctrl_usdhc1>;
580 cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
581 no-1-8-v;
582 disable-wp;
583 cap-sd-highspeed;
584 no-mmc;
585 no-sdio;
590 pinctrl-names = "default";
591 pinctrl-0 = <&pinctrl_usdhc3>;
592 bus-width = <8>;
593 no-1-8-v;
594 non-removable;
595 no-sd;
596 no-sdio;
601 pinctrl-names = "default";
602 pinctrl-0 = <&pinctrl_hog>;