Lines Matching +full:gpk0 +full:- +full:4
1 // SPDX-License-Identifier: GPL-2.0
12 /dts-v1/;
14 #include "exynos4412-ppmu-common.dtsi"
15 #include <dt-bindings/input/input.h>
16 #include <dt-bindings/gpio/gpio.h>
17 #include <dt-bindings/clock/samsung,s2mps11.h>
22 chassis-type = "watch";
29 stdout-path = &serial_1;
38 compatible = "samsung,secure-firmware";
42 gpio-keys {
43 compatible = "gpio-keys";
45 power-key {
49 debounce-interval = <10>;
50 wakeup-source;
54 wlan_pwrseq: mshc1-pwrseq {
55 compatible = "mmc-pwrseq-simple";
56 reset-gpios = <&gpe0 4 GPIO_ACTIVE_LOW>;
59 i2c_max77836: i2c-gpio-0 {
60 compatible = "i2c-gpio";
61 sda-gpios = <&gpd0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
62 scl-gpios = <&gpd0 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
63 #address-cells = <1>;
64 #size-cells = <0>;
68 interrupt-parent = <&gpx1>;
71 wakeup-source;
74 compatible = "maxim,max77836-muic";
78 compatible = "maxim,max77836-regulator";
80 regulator-name = "SAFEOUT";
84 regulator-name = "CHARGER";
85 regulator-min-microamp = <45000>;
86 regulator-max-microamp = <475000>;
87 regulator-boot-on;
91 regulator-name = "MOT_2.7V";
92 regulator-min-microvolt = <1100000>;
93 regulator-max-microvolt = <2700000>;
97 regulator-name = "UNUSED_LDO2";
98 regulator-min-microvolt = <800000>;
99 regulator-max-microvolt = <3950000>;
104 compatible = "maxim,max77836-charger";
106 maxim,constant-uvolt = <4350000>;
107 maxim,fast-charge-uamp = <225000>;
108 maxim,eoc-uamp = <7500>;
109 maxim,ovp-uvolt = <6500000>;
115 compatible = "regulator-haptic";
116 haptic-supply = <&motor_reg>;
117 min-microvolt = <1100000>;
118 max-microvolt = <2700000>;
121 thermal-zones {
122 cpu_thermal: cpu-thermal {
123 cooling-maps {
126 cooling-device = <&cpu0 5 5>,
131 cooling-device = <&cpu0 8 8>,
140 vdd-supply = <&ldo3_reg>;
142 assigned-clocks = <&cmu CLK_SCLK_TSADC>;
143 assigned-clock-rates = <6000000>;
145 thermistor-ap {
147 pullup-uv = <1800000>;
148 pullup-ohm = <100000>;
149 pulldown-ohm = <100000>;
150 io-channels = <&adc 0>;
153 thermistor-battery {
155 pullup-uv = <1800000>;
156 pullup-ohm = <100000>;
157 pulldown-ohm = <100000>;
158 io-channels = <&adc 1>;
163 devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>;
164 vdd-supply = <&buck1_reg>;
169 devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>;
170 vdd-supply = <&buck3_reg>;
214 cpu0-supply = <&buck2_reg>;
219 vbus-supply = <&safeout_reg>;
223 vusb_d-supply = <&ldo15_reg>;
224 vusb_a-supply = <&ldo12_reg>;
230 vddcore-supply = <&ldo6_reg>;
231 vddio-supply = <&ldo6_reg>;
232 samsung,burst-clock-frequency = <250000000>;
233 samsung,esc-clock-frequency = <20000000>;
234 samsung,pll-clock-frequency = <24000000>;
240 vdd3-supply = <&ldo16_reg>;
241 vci-supply = <&ldo20_reg>;
242 reset-gpios = <&gpe0 1 GPIO_ACTIVE_LOW>;
243 te-gpios = <&gpx0 6 GPIO_ACTIVE_HIGH>;
250 i80-if-timings {
251 cs-setup = <0>;
252 wr-setup = <0>;
253 wr-act = <1>;
254 wr-hold = <0>;
259 mali-supply = <&buck3_reg>;
264 #address-cells = <1>;
265 #size-cells = <0>;
266 samsung,i2c-sda-delay = <100>;
267 samsung,i2c-slave-addr = <0x10>;
268 samsung,i2c-max-bus-freq = <100000>;
272 compatible = "samsung,s2mps14-pmic";
273 interrupt-parent = <&gpx0>;
276 wakeup-source;
279 compatible = "samsung,s2mps14-clk";
280 #clock-cells = <1>;
281 clock-output-names = "s2mps14_ap", "unused",
287 regulator-name = "VAP_ALIVE_1.0V";
288 regulator-min-microvolt = <1000000>;
289 regulator-max-microvolt = <1000000>;
290 regulator-always-on;
292 regulator-state-mem {
293 regulator-on-in-suspend;
298 regulator-name = "VAP_M1_1.2V";
299 regulator-min-microvolt = <1200000>;
300 regulator-max-microvolt = <1200000>;
301 regulator-always-on;
303 regulator-state-mem {
304 regulator-off-in-suspend;
309 regulator-name = "VCC_AP_1.8V";
310 regulator-min-microvolt = <1800000>;
311 regulator-max-microvolt = <1800000>;
312 regulator-always-on;
314 regulator-state-mem {
315 regulator-off-in-suspend;
320 regulator-name = "VAP_AVDD_PLL1";
321 regulator-min-microvolt = <1800000>;
322 regulator-max-microvolt = <1800000>;
323 regulator-always-on;
325 regulator-state-mem {
326 regulator-off-in-suspend;
331 regulator-name = "VAP_PLL_ISO_1.0V";
332 regulator-min-microvolt = <1000000>;
333 regulator-max-microvolt = <1000000>;
334 regulator-always-on;
336 regulator-state-mem {
337 regulator-off-in-suspend;
342 regulator-name = "VAP_VMIPI_1.0V";
343 regulator-min-microvolt = <1000000>;
344 regulator-max-microvolt = <1000000>;
345 regulator-always-on;
347 regulator-state-mem {
348 regulator-off-in-suspend;
353 regulator-name = "VAP_AVDD_1.8V";
354 regulator-min-microvolt = <1800000>;
355 regulator-max-microvolt = <1800000>;
356 regulator-always-on;
358 regulator-state-mem {
359 regulator-off-in-suspend;
364 regulator-name = "VAP_USB_3.0V";
365 regulator-min-microvolt = <3000000>;
366 regulator-max-microvolt = <3000000>;
367 regulator-always-on;
369 regulator-state-mem {
370 regulator-off-in-suspend;
375 regulator-name = "V_LPDDR_1.2V";
376 regulator-min-microvolt = <1200000>;
377 regulator-max-microvolt = <1200000>;
378 regulator-always-on;
380 regulator-state-mem {
381 regulator-on-in-suspend;
386 regulator-name = "UNUSED_LDO10";
387 regulator-min-microvolt = <1000000>;
388 regulator-max-microvolt = <1000000>;
390 regulator-state-mem {
391 regulator-off-in-suspend;
396 regulator-name = "V_EMMC_1.8V";
397 regulator-min-microvolt = <1800000>;
398 regulator-max-microvolt = <1800000>;
399 samsung,ext-control-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>;
403 regulator-name = "V_EMMC_2.8V";
404 regulator-min-microvolt = <2800000>;
405 regulator-max-microvolt = <2800000>;
406 samsung,ext-control-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>;
410 regulator-name = "CAM_AVDD_2.8V";
411 regulator-min-microvolt = <2800000>;
412 regulator-max-microvolt = <2800000>;
414 regulator-state-mem {
415 regulator-off-in-suspend;
420 regulator-name = "UNUSED_LDO14";
421 regulator-min-microvolt = <2700000>;
422 regulator-max-microvolt = <2700000>;
424 regulator-state-mem {
425 regulator-off-in-suspend;
430 regulator-name = "TSP_AVDD_3.3V";
431 regulator-min-microvolt = <3300000>;
432 regulator-max-microvolt = <3300000>;
434 regulator-state-mem {
435 regulator-off-in-suspend;
440 regulator-name = "LCD_VDD_3.3V";
441 regulator-min-microvolt = <3300000>;
442 regulator-max-microvolt = <3300000>;
444 regulator-state-mem {
445 regulator-off-in-suspend;
450 regulator-name = "V_IRLED_3.3V";
451 regulator-min-microvolt = <3300000>;
452 regulator-max-microvolt = <3300000>;
454 regulator-state-mem {
455 regulator-off-in-suspend;
460 regulator-name = "CAM_AF_2.8V";
461 regulator-min-microvolt = <2800000>;
462 regulator-max-microvolt = <2800000>;
464 regulator-state-mem {
465 regulator-off-in-suspend;
470 regulator-name = "TSP_VDD_1.8V";
471 regulator-min-microvolt = <1800000>;
472 regulator-max-microvolt = <1800000>;
474 regulator-state-mem {
475 regulator-off-in-suspend;
480 regulator-name = "LCD_VDD_1.8V";
481 regulator-min-microvolt = <1800000>;
482 regulator-max-microvolt = <1800000>;
484 regulator-state-mem {
485 regulator-off-in-suspend;
490 regulator-name = "CAM_IO_1.8V";
491 regulator-min-microvolt = <1800000>;
492 regulator-max-microvolt = <1800000>;
494 regulator-state-mem {
495 regulator-off-in-suspend;
500 regulator-name = "CAM_DVDD_1.2V";
501 regulator-min-microvolt = <1200000>;
502 regulator-max-microvolt = <1200000>;
504 regulator-state-mem {
505 regulator-off-in-suspend;
510 regulator-name = "HRM_VCC_1.8V";
511 regulator-min-microvolt = <1800000>;
512 regulator-max-microvolt = <1800000>;
513 regulator-always-on;
517 regulator-name = "HRM_VCC_3.3V";
518 regulator-min-microvolt = <3000000>;
519 regulator-max-microvolt = <3000000>;
521 regulator-state-mem {
522 regulator-off-in-suspend;
527 regulator-name = "UNUSED_LDO25";
528 regulator-min-microvolt = <3000000>;
529 regulator-max-microvolt = <3000000>;
531 regulator-state-mem {
532 regulator-off-in-suspend;
537 regulator-name = "VAP_MIF_1.0V";
538 regulator-min-microvolt = <800000>;
539 regulator-max-microvolt = <900000>;
540 regulator-always-on;
542 regulator-state-mem {
543 regulator-off-in-suspend;
548 regulator-name = "VAP_ARM_1.0V";
549 regulator-min-microvolt = <850000>;
550 regulator-max-microvolt = <1150000>;
551 regulator-always-on;
553 regulator-state-mem {
554 regulator-off-in-suspend;
559 regulator-name = "VAP_INT3D_1.0V";
560 regulator-min-microvolt = <850000>;
561 regulator-max-microvolt = <1000000>;
562 regulator-always-on;
564 regulator-state-mem {
565 regulator-off-in-suspend;
570 regulator-name = "VCC_SUB_1.95V";
571 regulator-min-microvolt = <1950000>;
572 regulator-max-microvolt = <1950000>;
573 regulator-always-on;
575 regulator-state-mem {
576 regulator-on-in-suspend;
581 regulator-name = "VCC_SUB_1.35V";
582 regulator-min-microvolt = <1350000>;
583 regulator-max-microvolt = <1350000>;
584 regulator-always-on;
586 regulator-state-mem {
587 regulator-on-in-suspend;
595 #address-cells = <1>;
596 #size-cells = <0>;
597 samsung,i2c-sda-delay = <100>;
598 samsung,i2c-slave-addr = <0x10>;
599 samsung,i2c-max-bus-freq = <400000>;
603 compatible = "maxim,max77836-battery";
604 interrupt-parent = <&gpx1>;
619 broken-cd;
620 non-removable;
621 cap-mmc-highspeed;
622 desc-num = <4>;
623 mmc-hs200-1_8v;
624 card-detect-delay = <200>;
625 vmmc-supply = <&ldo12_reg>;
626 clock-frequency = <100000000>;
627 max-frequency = <100000000>;
628 samsung,dw-mshc-ciu-div = <1>;
629 samsung,dw-mshc-sdr-timing = <0 1>;
630 samsung,dw-mshc-ddr-timing = <1 2>;
631 pinctrl-names = "default";
632 pinctrl-0 = <&sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>;
633 bus-width = <8>;
640 #address-cells = <1>;
641 #size-cells = <0>;
643 non-removable;
644 cap-sd-highspeed;
645 cap-sdio-irq;
646 keep-power-in-suspend;
647 samsung,dw-mshc-ciu-div = <1>;
648 samsung,dw-mshc-sdr-timing = <0 1>;
649 samsung,dw-mshc-ddr-timing = <1 2>;
650 pinctrl-names = "default";
651 pinctrl-0 = <&sd1_clk &sd1_cmd &sd1_bus1 &sd1_bus4>;
652 bus-width = <4>;
654 mmc-pwrseq = <&wlan_pwrseq>;
657 compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac";
660 interrupt-parent = <&gpx1>;
662 interrupt-names = "host-wake";
667 assigned-clocks = <&cmu CLK_SCLK_UART0>;
668 assigned-clock-rates = <100000000>;
672 compatible = "brcm,bcm4330-bt";
673 max-speed = <3000000>;
674 shutdown-gpios = <&gpe0 0 GPIO_ACTIVE_HIGH>;
675 device-wakeup-gpios = <&gpx3 1 GPIO_ACTIVE_HIGH>;
676 host-wakeup-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>;
686 vtmu-supply = <&ldo7_reg>;
692 clock-names = "rtc", "rtc_src";
697 clock-frequency = <24000000>;
701 pinctrl-names = "default";
702 pinctrl-0 = <&initial0 &sleep0>;
704 initial0: initial-state {
705 PIN_IN(gpa1-4, DOWN, LV1);
706 PIN_IN(gpa1-5, DOWN, LV1);
708 PIN_IN(gpc0-0, DOWN, LV1);
709 PIN_IN(gpc0-1, DOWN, LV1);
710 PIN_IN(gpc0-2, DOWN, LV1);
711 PIN_IN(gpc0-3, DOWN, LV1);
712 PIN_IN(gpc0-4, DOWN, LV1);
714 PIN_IN(gpd0-0, DOWN, LV1);
715 PIN_IN(gpd0-1, DOWN, LV1);
718 sleep0: sleep-state {
719 PIN_SLP(gpa0-0, INPUT, DOWN);
720 PIN_SLP(gpa0-1, INPUT, DOWN);
721 PIN_SLP(gpa0-2, INPUT, DOWN);
722 PIN_SLP(gpa0-3, INPUT, DOWN);
723 PIN_SLP(gpa0-4, INPUT, DOWN);
724 PIN_SLP(gpa0-5, INPUT, DOWN);
725 PIN_SLP(gpa0-6, INPUT, DOWN);
726 PIN_SLP(gpa0-7, INPUT, DOWN);
728 PIN_SLP(gpa1-0, INPUT, DOWN);
729 PIN_SLP(gpa1-1, INPUT, DOWN);
730 PIN_SLP(gpa1-2, INPUT, DOWN);
731 PIN_SLP(gpa1-3, INPUT, DOWN);
732 PIN_SLP(gpa1-4, INPUT, DOWN);
733 PIN_SLP(gpa1-5, INPUT, DOWN);
735 PIN_SLP(gpb-0, PREV, NONE);
736 PIN_SLP(gpb-1, PREV, NONE);
737 PIN_SLP(gpb-2, PREV, NONE);
738 PIN_SLP(gpb-3, PREV, NONE);
739 PIN_SLP(gpb-4, INPUT, DOWN);
740 PIN_SLP(gpb-5, INPUT, DOWN);
741 PIN_SLP(gpb-6, INPUT, DOWN);
742 PIN_SLP(gpb-7, INPUT, DOWN);
744 PIN_SLP(gpc0-0, INPUT, DOWN);
745 PIN_SLP(gpc0-1, INPUT, DOWN);
746 PIN_SLP(gpc0-2, INPUT, DOWN);
747 PIN_SLP(gpc0-3, INPUT, DOWN);
748 PIN_SLP(gpc0-4, INPUT, DOWN);
750 PIN_SLP(gpc1-0, INPUT, DOWN);
751 PIN_SLP(gpc1-1, INPUT, DOWN);
752 PIN_SLP(gpc1-2, INPUT, DOWN);
753 PIN_SLP(gpc1-3, INPUT, DOWN);
754 PIN_SLP(gpc1-4, INPUT, DOWN);
756 PIN_SLP(gpd0-0, INPUT, DOWN);
757 PIN_SLP(gpd0-1, INPUT, DOWN);
758 PIN_SLP(gpd0-2, INPUT, NONE);
759 PIN_SLP(gpd0-3, INPUT, NONE);
761 PIN_SLP(gpd1-0, INPUT, NONE);
762 PIN_SLP(gpd1-1, INPUT, NONE);
763 PIN_SLP(gpd1-2, INPUT, NONE);
764 PIN_SLP(gpd1-3, INPUT, NONE);
769 pinctrl-names = "default";
770 pinctrl-0 = <&initial1 &sleep1>;
772 initial1: initial-state {
773 PIN_IN(gpe0-6, DOWN, LV1);
774 PIN_IN(gpe0-7, DOWN, LV1);
776 PIN_IN(gpe1-0, DOWN, LV1);
777 PIN_IN(gpe1-3, DOWN, LV1);
778 PIN_IN(gpe1-4, DOWN, LV1);
779 PIN_IN(gpe1-5, DOWN, LV1);
780 PIN_IN(gpe1-6, DOWN, LV1);
782 PIN_IN(gpk2-0, DOWN, LV1);
783 PIN_IN(gpk2-1, DOWN, LV1);
784 PIN_IN(gpk2-2, DOWN, LV1);
785 PIN_IN(gpk2-3, DOWN, LV1);
786 PIN_IN(gpk2-4, DOWN, LV1);
787 PIN_IN(gpk2-5, DOWN, LV1);
788 PIN_IN(gpk2-6, DOWN, LV1);
790 PIN_IN(gpm0-0, DOWN, LV1);
791 PIN_IN(gpm0-1, DOWN, LV1);
792 PIN_IN(gpm0-2, DOWN, LV1);
793 PIN_IN(gpm0-3, DOWN, LV1);
794 PIN_IN(gpm0-4, DOWN, LV1);
795 PIN_IN(gpm0-5, DOWN, LV1);
796 PIN_IN(gpm0-6, DOWN, LV1);
797 PIN_IN(gpm0-7, DOWN, LV1);
799 PIN_IN(gpm1-0, DOWN, LV1);
800 PIN_IN(gpm1-1, DOWN, LV1);
801 PIN_IN(gpm1-2, DOWN, LV1);
802 PIN_IN(gpm1-3, DOWN, LV1);
803 PIN_IN(gpm1-4, DOWN, LV1);
804 PIN_IN(gpm1-5, DOWN, LV1);
805 PIN_IN(gpm1-6, DOWN, LV1);
807 PIN_IN(gpm2-0, DOWN, LV1);
808 PIN_IN(gpm2-1, DOWN, LV1);
810 PIN_IN(gpm3-0, DOWN, LV1);
811 PIN_IN(gpm3-1, DOWN, LV1);
812 PIN_IN(gpm3-2, DOWN, LV1);
813 PIN_IN(gpm3-3, DOWN, LV1);
814 PIN_IN(gpm3-4, DOWN, LV1);
816 PIN_IN(gpm4-1, DOWN, LV1);
817 PIN_IN(gpm4-2, DOWN, LV1);
818 PIN_IN(gpm4-3, DOWN, LV1);
819 PIN_IN(gpm4-4, DOWN, LV1);
820 PIN_IN(gpm4-5, DOWN, LV1);
821 PIN_IN(gpm4-6, DOWN, LV1);
822 PIN_IN(gpm4-7, DOWN, LV1);
825 sleep1: sleep-state {
826 PIN_SLP(gpe0-0, PREV, NONE);
827 PIN_SLP(gpe0-1, PREV, NONE);
828 PIN_SLP(gpe0-2, INPUT, DOWN);
829 PIN_SLP(gpe0-3, INPUT, UP);
830 PIN_SLP(gpe0-4, INPUT, DOWN);
831 PIN_SLP(gpe0-5, INPUT, DOWN);
832 PIN_SLP(gpe0-6, INPUT, DOWN);
833 PIN_SLP(gpe0-7, INPUT, DOWN);
835 PIN_SLP(gpe1-0, INPUT, DOWN);
836 PIN_SLP(gpe1-1, PREV, NONE);
837 PIN_SLP(gpe1-2, INPUT, DOWN);
838 PIN_SLP(gpe1-3, INPUT, DOWN);
839 PIN_SLP(gpe1-4, INPUT, DOWN);
840 PIN_SLP(gpe1-5, INPUT, DOWN);
841 PIN_SLP(gpe1-6, INPUT, DOWN);
842 PIN_SLP(gpe1-7, INPUT, NONE);
844 PIN_SLP(gpe2-0, INPUT, NONE);
845 PIN_SLP(gpe2-1, INPUT, NONE);
846 PIN_SLP(gpe2-2, INPUT, NONE);
848 PIN_SLP(gpk0-0, INPUT, DOWN);
849 PIN_SLP(gpk0-1, INPUT, DOWN);
850 PIN_SLP(gpk0-2, OUT0, NONE);
851 PIN_SLP(gpk0-3, INPUT, DOWN);
852 PIN_SLP(gpk0-4, INPUT, DOWN);
853 PIN_SLP(gpk0-5, INPUT, DOWN);
854 PIN_SLP(gpk0-6, INPUT, DOWN);
855 PIN_SLP(gpk0-7, INPUT, DOWN);
857 PIN_SLP(gpk1-0, INPUT, DOWN);
858 PIN_SLP(gpk1-1, INPUT, DOWN);
859 PIN_SLP(gpk1-2, INPUT, DOWN);
860 PIN_SLP(gpk1-3, INPUT, DOWN);
861 PIN_SLP(gpk1-4, INPUT, DOWN);
862 PIN_SLP(gpk1-5, INPUT, DOWN);
863 PIN_SLP(gpk1-6, INPUT, DOWN);
865 PIN_SLP(gpk2-0, INPUT, DOWN);
866 PIN_SLP(gpk2-1, INPUT, DOWN);
867 PIN_SLP(gpk2-2, INPUT, DOWN);
868 PIN_SLP(gpk2-3, INPUT, DOWN);
869 PIN_SLP(gpk2-4, INPUT, DOWN);
870 PIN_SLP(gpk2-5, INPUT, DOWN);
871 PIN_SLP(gpk2-6, INPUT, DOWN);
873 PIN_SLP(gpl0-0, INPUT, DOWN);
874 PIN_SLP(gpl0-1, INPUT, DOWN);
875 PIN_SLP(gpl0-2, INPUT, DOWN);
876 PIN_SLP(gpl0-3, INPUT, DOWN);
878 PIN_SLP(gpm0-0, INPUT, DOWN);
879 PIN_SLP(gpm0-1, INPUT, DOWN);
880 PIN_SLP(gpm0-2, INPUT, DOWN);
881 PIN_SLP(gpm0-3, INPUT, DOWN);
882 PIN_SLP(gpm0-4, INPUT, DOWN);
883 PIN_SLP(gpm0-5, INPUT, DOWN);
884 PIN_SLP(gpm0-6, INPUT, DOWN);
885 PIN_SLP(gpm0-7, INPUT, DOWN);
887 PIN_SLP(gpm1-0, INPUT, DOWN);
888 PIN_SLP(gpm1-1, INPUT, DOWN);
889 PIN_SLP(gpm1-2, INPUT, DOWN);
890 PIN_SLP(gpm1-3, INPUT, DOWN);
891 PIN_SLP(gpm1-4, INPUT, DOWN);
892 PIN_SLP(gpm1-5, INPUT, DOWN);
893 PIN_SLP(gpm1-6, INPUT, DOWN);
895 PIN_SLP(gpm2-0, INPUT, DOWN);
896 PIN_SLP(gpm2-1, INPUT, DOWN);
897 PIN_SLP(gpm2-2, INPUT, DOWN);
898 PIN_SLP(gpm2-3, INPUT, DOWN);
899 PIN_SLP(gpm2-4, INPUT, DOWN);
901 PIN_SLP(gpm3-0, INPUT, DOWN);
902 PIN_SLP(gpm3-1, INPUT, DOWN);
903 PIN_SLP(gpm3-2, INPUT, DOWN);
904 PIN_SLP(gpm3-3, INPUT, DOWN);
905 PIN_SLP(gpm3-4, INPUT, DOWN);
906 PIN_SLP(gpm3-5, INPUT, DOWN);
907 PIN_SLP(gpm3-6, INPUT, DOWN);
908 PIN_SLP(gpm3-7, INPUT, DOWN);
910 PIN_SLP(gpm4-0, INPUT, DOWN);
911 PIN_SLP(gpm4-1, INPUT, DOWN);
912 PIN_SLP(gpm4-2, INPUT, DOWN);
913 PIN_SLP(gpm4-3, INPUT, DOWN);
914 PIN_SLP(gpm4-4, INPUT, DOWN);
915 PIN_SLP(gpm4-5, INPUT, DOWN);
916 PIN_SLP(gpm4-6, INPUT, DOWN);
917 PIN_SLP(gpm4-7, INPUT, DOWN);