Lines Matching +full:vga +full:- +full:format
9 Author: Roman.Hodek@informatik.uni-erlangen.de (Roman Hodek)
11 Update: jds@kom.auc.dk (Jes Sorensen) and faq@linux-m68k.org (Chris Lawrence)
58 ----------
76 /dev/ram: -> 0x0100 (initial ramdisk)
77 /dev/hda: -> 0x0300 (first IDE disk)
78 /dev/hdb: -> 0x0340 (second IDE disk)
79 /dev/sda: -> 0x0800 (first SCSI disk)
80 /dev/sdb: -> 0x0810 (second SCSI disk)
81 /dev/sdc: -> 0x0820 (third SCSI disk)
82 /dev/sdd: -> 0x0830 (forth SCSI disk)
83 /dev/sde: -> 0x0840 (fifth SCSI disk)
84 /dev/fd : -> 0x0200 (floppy disk)
97 on. Since the number is just added, you can also force the disk format
107 to /dev/fd0D720 as an abbreviation for floppy driver #0 in DD format,
127 SCSI CD-ROM drive, you boot from it by "root=0b00". Here, hex "0b" =
128 decimal 11 is the major of SCSI CD-ROMs, and the minor 0 stands for
133 root partition uses a partition table format with unique partition
135 "root=PARTUUID=00112233-4455-6677-8899-AABBCCDDEEFF". It is also
139 00112233-4455-6677-8899-AABBCCDDEEFF then partition 3 may be found as
142 PARTUUID=00112233-4455-6677-8899-AABBCCDDEEFF/PARTNROFF=-2
145 "Documentation/admin-guide/kernel-parameters.rst".
149 -----------
155 filesystem read-only or read-write. The default is read-only, except
156 for ramdisks, which default to read-write.
160 ----------
170 -----------
187 2.3) and at run time with "dmesg -n 8".
191 - "ser":
192 built-in serial port; parameters: 9600bps, 8N1
193 - "mem":
200 - "ser1":
201 ST-MFP serial port ("Modem1"); parameters: 9600bps, 8N1
202 - "ser2":
204 - "ser" :
207 - "midi":
209 - "par" :
219 ------------------
239 -----------
248 -----------
250 :Syntax: ether=[<irq>[,<base_addr>[,<mem_start>[,<mem_end>]]]],<dev-name>
252 <dev-name> is the name of a net driver, as specified in
256 The non-ethernet drivers (sl, ppp, dummy, lo) obviously ignore the
259 are really Plug-'n-Play, so the "ether=" option is useless altogether
264 --------
277 -------------------
288 --------
293 the number of 512-byte buffers reserved for tape operations for each
301 --------------
303 :Syntax: dmasound=[<buffers>,<buffer-size>[,<catch-radius>]]
307 to use (minimum 4, default 4), <buffer-size> is the size of each
308 buffer in kilobytes (minimum 4, default 32) and <catch-radius> says
311 AU-Files on the Falcon with its hardware frequency of 8195Hz and thus
320 -----------
322 :Syntax: video=<fbname>:<sub-options...>
326 <sub-options> is a comma-separated list of the sub-options listed
332 might need to update your boot-scripts if upgrading to 2.x from
340 -----------------
342 This sub-option may be any of the predefined video modes, as listed
347 - stlow : 320x200x4
348 - stmid, default5 : 640x200x2
349 - sthigh, default4: 640x400x1
350 - ttlow : 320x480x8, TT only
351 - ttmid, default1 : 640x480x4, TT only
352 - tthigh, default2: 1280x960x1, TT only
353 - vga2 : 640x480x1, Falcon only
354 - vga4 : 640x480x2, Falcon only
355 - vga16, default3 : 640x480x4, Falcon only
356 - vga256 : 640x480x8, Falcon only
357 - falh2 : 896x608x1, Falcon only
358 - falh16 : 896x608x4, Falcon only
365 activated by a "external:" sub-option.
368 --------------
375 -----------
385 ------------------
403 ----------------
421 ----------------
437 The first 3 parameters of this sub-option should be obvious: <xres>,
451 built-in Atari video modes, I think there is no card that
488 your card is somehow VGA compatible, you can tell the kernel the base
489 address of the VGA register set, so it can change the color lookup
504 "vga" (which is also the default) and "mv300" (SANG MV300) are
510 initialisation of the video-card.
512 therefore we don't support hardware-dependent functions like hardware-scroll,
516 --------------
522 -------------------
527 with a fixed-frequency monitor! For now, only the Falcon frame buffer
534 The defaults are 58;62;31;32 (VGA compatible).
539 ------------
555 --------------
557 :Syntax: atamouse=<x-threshold>,[<y-threshold>]
573 -------------
584 track buffering (1) or not (0). The default is machine-dependent:
592 -------------
594 :Syntax: atascsi=<can_queue>[,<cmd_per_lun>[,<scat-gat>[,<host-id>[,<tagged>]]]]
599 defaults depend on whether TT-style or Falcon-style SCSI is used.
601 TT-SCSI and the latter to Falcon-SCSI. If an illegal value is given
626 no scatter-gather:
628 full scatter-gather:
631 <scat-gat>:
632 Size of the scatter-gather table, i.e. the number of requests
635 value is forced to 0 on a Falcon, since scatter-gather isn't
636 possible with the ST-DMA. Not using scatter-gather hurts
639 <host-id>:
642 be unique. Default: determined at run time: If the NV-RAM checksum
643 is valid, and bit 7 in byte 30 of the NV-RAM is set, the lower 3
657 tagged queuing (:-().
660 -------------
668 The <list of switches> is a comma-separated list of the following
689 switch-on is done after video initialization, and somehow synchronized
695 earlier initialization (`ov_`-less) takes precedence. But the
696 switching-off on reset still happens in this case.
702 -----------
704 :Syntax: video=<fbname>:<sub-options...>
713 The <sub-options> is a comma-separated list of the sub-options listed
715 "video"-option (4.1), but knows fewer sub-options.
718 -----------------
727 - ntsc : 640x200, 15 kHz, 60 Hz
728 - ntsc-lace : 640x400, 15 kHz, 60 Hz interlaced
731 - pal : 640x256, 15 kHz, 50 Hz
732 - pal-lace : 640x512, 15 kHz, 50 Hz interlaced
735 - multiscan : 640x480, 29 kHz, 57 Hz
736 - multiscan-lace : 640x960, 29 kHz, 57 Hz interlaced
737 - euro36 : 640x200, 15 kHz, 72 Hz
738 - euro36-lace : 640x400, 15 kHz, 72 Hz interlaced
739 - euro72 : 640x400, 29 kHz, 68 Hz
740 - euro72-lace : 640x800, 29 kHz, 68 Hz interlaced
741 - super72 : 800x300, 23 kHz, 70 Hz
742 - super72-lace : 800x600, 23 kHz, 70 Hz interlaced
743 - dblntsc-ff : 640x400, 27 kHz, 57 Hz
744 - dblntsc-lace : 640x800, 27 kHz, 57 Hz interlaced
745 - dblpal-ff : 640x512, 27 kHz, 47 Hz
746 - dblpal-lace : 640x1024, 27 kHz, 47 Hz interlaced
747 - dblntsc : 640x200, 27 kHz, 57 Hz doublescan
748 - dblpal : 640x256, 27 kHz, 47 Hz doublescan
750 VGA modes:
751 - vga : 640x480, 31 kHz, 60 Hz
752 - vga70 : 640x400, 31 kHz, 70 Hz
754 Please notice that the ECS and VGA modes require either an ECS or AGA
755 chipset, and that these modes are limited to 2-bit color for the ECS
756 chipset and 8-bit color for the AGA chipset.
759 ------------
761 :Syntax: depth:<nr. of bit-planes>
763 Specify the number of bit-planes for the selected video-mode.
766 --------------
769 "inverse" sub-option for the Atari.
772 -----------
777 "font" sub-option for the Atari, except that `PEARL8x8` is used instead
782 -------------------
797 ----------------
806 -------------
808 :Syntax: wd33c93=<sub-options...>
813 The <sub-options> is a comma-separated list of the sub-options listed
817 -------------
823 device. To maintain backwards compatibility, a command-line such as
829 -------------
834 period. Default is 500; acceptable values are 250 - 1000.
837 -----------------
846 ------------
851 types of debug output to printed - see the DB_xxx defines in
855 ------------
863 hostadapter and the SCSI-clock jumper present on some GVP
867 -----------
870 than one wd33c93-based host adapter in the system.
873 ------------
886 -----------
888 :Syntax: gvp11=<addr-mask>
891 address-mask settings correctly which made it necessary for some