Lines Matching full:single

4 - compatible : "pinctrl-single" or "pinconf-single".
5   "pinctrl-single" means that pinconf isn't supported.
6   "pinconf-single" means that generic pinconf is supported.
11   or 2 for pinctrl-single,pins and set to 2 for pinctrl-single,bits
13 - pinctrl-single,register-width : pinmux register access width in bits
15 - pinctrl-single,function-mask : mask of allowed pinmux function bits
19 - pinctrl-single,function-off : function off mode for disabled state if
23 - pinctrl-single,bit-per-mux : boolean to indicate that one register controls
24   more than one pin, for which "pinctrl-single,function-mask" property specifies
27 - pinctrl-single,drive-strength : array of value that are used to configure
32 		pinctrl-single,power-source = <0x30 0xf0>;
34 - pinctrl-single,bias-pullup : array of value that are used to configure the
38 		pinctrl-single,bias-pullup = <0 1 0 1>;
40 - pinctrl-single,bias-pulldown : array of value that are used to configure the
44 		pinctrl-single,bias-pulldown = <2 2 0 2>;
47     pinctrl-single,bias-pullup & pinctrl-single,bias-pulldown. One bit means
50     use pinctrl-single,bias-pullup & pinctrl-single,bias-pulldown. Input bias
53     pinctrl-single,bias-disable. Because pinctrl single driver could implement
56 - pinctrl-single,input-schmitt : array of value that are used to configure
61 		pinctrl-single,input-schmitt = <0x30 0x70>;
63 - pinctrl-single,input-schmitt-enable : array of value that are used to
67 		pinctrl-single,input-schmitt-enable = <0x30 0x40 0 0x70>;
69 - pinctrl-single,low-power-mode : array of value that are used to configure
74 		pinctrl-single,low-power-mode = <0x288 0x388>;
76 - pinctrl-single,gpio-range : list of value that are used to configure a GPIO
79   The number of parameters is depend on #pinctrl-single,gpio-range-cells
83 		pinctrl-single,gpio-range = <&range 0 3 0>, <&range 3 9 1>;
86   interrupts for wake-up events for example. In this case pinctrl-single
93 pinctrl-single,bit-per-mux is set), and uses the common pinctrl bindings as
96 The pin configuration nodes for pinctrl-single are specified as pinctrl
97 register offset and values using pinctrl-single,pins. Only the bits specified
98 in pinctrl-single,function-mask are updated.
102 	pinctrl-single,pins = <0xdc 0x118>;
109 	pinctrl-single,pins = <0xdc 0x30 0x07>;
116 pinctrl-single,bits need to be used which takes three parameters:
118 	pinctrl-single,bits = <0xdc 0x18 0xff>;
127 by pinctrl-single,gpio-range property.
130 - #pinctrl-single,gpio-range-cells : the number of parameters after phandle in
131   pinctrl-single,gpio-range property.
134 		#pinctrl-single,gpio-range-cells = <3>;
144 	compatible = "pinctrl-single";
150 	pinctrl-single,register-width = <16>;
151 	pinctrl-single,function-mask = <0xffff>;
156 	compatible = "pinctrl-single";
162 	pinctrl-single,register-width = <16>;
163 	pinctrl-single,function-mask = <0xffff>;
167 	compatible = "pinctrl-single";
168 	reg = <0x48002274 4>;	/* Single register */
171 	pinctrl-single,bit-per-mux;
172 	pinctrl-single,register-width = <32>;
173 	pinctrl-single,function-mask = <0x5F>;
178 	compatible = "pinconf-single";
184 	pinctrl-single,register-width = <32>;
185 	pinctrl-single,function-mask = <7>;
188 	pinctrl-single,gpio-range = <&range 0 3 0>, <&range 3 9 1>,
194 		#pinctrl-single,gpio-range-cells = <3>;
211 		pinctrl-single,pins = <
220 		pinctrl-single,pins = <
224 		pinctrl-single,bias-pulldown = <0 2 2>;
225 		pinctrl-single,bias-pullup = <0 1 1>;
230 		pinctrl-single,pins = <
241 		pinctrl-single,bits = <
247 		pinctrl-single,bits = <