Lines Matching +full:proximity +full:- +full:near +full:- +full:level
3 Contact: linux-iio@vger.kernel.org
11 Contact: linux-iio@vger.kernel.org
25 Contact: linux-iio@vger.kernel.org
31 Contact: linux-iio@vger.kernel.org
38 Contact: linux-iio@vger.kernel.org
44 The contents of the label are free-form, but there are some
47 For proximity sensors which give the proximity (of a person) to
51 * "proximity-wifi"
52 * "proximity-lte"
53 * "proximity-wifi-lte"
54 * "proximity-wifi-left"
55 * "proximity-wifi-right"
57 These are used to indicate to userspace that these proximity
60 The "-left" and "-right" labels are for devices with multiple
63 In some laptops/tablets the standardized proximity sensor labels
64 instead indicate proximity to a specific part of the device:
66 * "proximity-palmrest" indicates proximity to the keyboard's palmrest
67 * "proximity-palmrest-left" indicates proximity to the left part of the palmrest
68 * "proximity-palmrest-right" indicates proximity to the right part of the palmrest
69 * "proximity-lap" indicates the device is being used on someone's lap
71 Note "proximity-lap" is special in that its value may be
75 For accelerometers used in 2-in-1s with 360° (yoga-style) hinges,
79 * "accel-base"
80 * "accel-display"
85 * "accel-camera"
89 Contact: linux-iio@vger.kernel.org
99 Contact: linux-iio@vger.kernel.org
110 The stm32-timer-trigger has the additional characteristic that
119 Contact: linux-iio@vger.kernel.org
124 - a small discrete set of values like "0 2 4 6 8"
125 - a range with minimum, step and maximum frequencies like
130 Contact: linux-iio@vger.kernel.org
137 Contact: linux-iio@vger.kernel.org
146 Contact: linux-iio@vger.kernel.org
156 channels refer to the same signal. The 'i' channel contains the in-phase
160 What: /sys/bus/iio/devices/iio:deviceX/in_voltageY-voltageZ_raw
162 Contact: linux-iio@vger.kernel.org
165 channel Y - channel Z where these channel numbers apply to the
174 Contact: linux-iio@vger.kernel.org
185 Contact: linux-iio@vger.kernel.org
194 Contact: linux-iio@vger.kernel.org
199 What: /sys/.../iio:deviceX/in_capacitanceY-capacitanceZ_raw
201 Contact: linux-iio@vger.kernel.org
204 channel Y - channel Z where these channel numbers apply to the
210 What: /sys/.../iio:deviceX/in_capacitanceY-capacitanceZ_zeropoint
212 Contact: linux-iio@vger.kernel.org
236 Contact: linux-iio@vger.kernel.org
242 between ambient (reference) and distant temperature for contact-
248 Contact: linux-iio@vger.kernel.org
256 Contact: linux-iio@vger.kernel.org
267 Contact: linux-iio@vger.kernel.org
276 Contact: linux-iio@vger.kernel.org
285 Contact: linux-iio@vger.kernel.org
293 Contact: linux-iio@vger.kernel.org
306 Contact: linux-iio@vger.kernel.org
317 Contact: linux-iio@vger.kernel.org
327 Contact: linux-iio@vger.kernel.org
337 Contact: linux-iio@vger.kernel.org
345 Contact: linux-iio@vger.kernel.org
353 Contact: linux-iio@vger.kernel.org
361 Contact: linux-iio@vger.kernel.org
367 Contact: linux-iio@vger.kernel.org
374 Contact: linux-iio@vger.kernel.org
380 Contact: linux-iio@vger.kernel.org
412 Contact: linux-iio@vger.kernel.org
435 What: /sys/bus/iio/devices/iio:deviceX/in_voltage-voltage_scale
470 Contact: linux-iio@vger.kernel.org
491 Contact: linux-iio@vger.kernel.org
502 Contact: linux-iio@vger.kernel.org
506 - a small discrete set of values like "0 2 4 6 8"
507 - a range specified as "[min step max]"
529 Contact: linux-iio@vger.kernel.org
540 Contact: linux-iio@vger.kernel.org
551 Contact: linux-iio@vger.kernel.org
560 Contact: linux-iio@vger.kernel.org
568 Contact: linux-iio@vger.kernel.org
580 What: /sys/.../iio:deviceX/in_voltage-voltage_scale_available
587 Contact: linux-iio@vger.kernel.org
599 Contact: linux-iio@vger.kernel.org
606 Contact: linux-iio@vger.kernel.org
615 Contact: linux-iio@vger.kernel.org
625 Contact: linux-iio@vger.kernel.org
634 Contact: linux-iio@vger.kernel.org
646 Contact: linux-iio@vger.kernel.org
658 Contact: linux-iio@vger.kernel.org
681 Contact: linux-iio@vger.kernel.org
691 Contact: linux-iio@vger.kernel.org
701 Contact: linux-iio@vger.kernel.org
728 Contact: linux-iio@vger.kernel.org
749 Contact: linux-iio@vger.kernel.org
752 to user-space.
790 Contact: linux-iio@vger.kernel.org
844 Contact: linux-iio@vger.kernel.org
869 Contact: linux-iio@vger.kernel.org
881 Contact: linux-iio@vger.kernel.org
887 signal is allowed to remain out-of-range before a reset
937 Contact: linux-iio@vger.kernel.org
963 Contact: linux-iio@vger.kernel.org
1021 Contact: linux-iio@vger.kernel.org
1071 Contact: linux-iio@vger.kernel.org
1161 Contact: linux-iio@vger.kernel.org
1171 Contact: linux-iio@vger.kernel.org
1181 Contact: linux-iio@vger.kernel.org
1196 Contact: linux-iio@vger.kernel.org
1210 Contact: linux-iio@vger.kernel.org
1236 Contact: linux-iio@vger.kernel.org
1247 Contact: linux-iio@vger.kernel.org
1260 Contact: linux-iio@vger.kernel.org
1273 Contact: linux-iio@vger.kernel.org
1281 Contact: linux-iio@vger.kernel.org
1290 Contact: linux-iio@vger.kernel.org
1300 Contact: linux-iio@vger.kernel.org
1307 Contact: linux-iio@vger.kernel.org
1313 Contact: linux-iio@vger.kernel.org
1324 Contact: linux-iio@vger.kernel.org
1348 What: /sys/.../iio:deviceX/bufferY/in_voltageY-voltageZ_en
1360 Contact: linux-iio@vger.kernel.org
1381 Contact: linux-iio@vger.kernel.org
1384 and hence the form in which it is read from user-space.
1405 Contact: linux-iio@vger.kernel.org
1437 Contact: linux-iio@vger.kernel.org
1441 what is enabled and may not be contiguous. Thus for user-space
1452 Contact: linux-iio@vger.kernel.org
1459 Contact: linux-iio@vger.kernel.org
1466 Contact: linux-iio@vger.kernel.org
1469 low_noise: reduce noise level from ADC,
1477 Contact: linux-iio@vger.kernel.org
1486 Contact: linux-iio@vger.kernel.org
1494 Contact: linux-iio@vger.kernel.org
1497 on-chip EEPROM. After power-up or chip reset the device will
1504 Contact: linux-iio@vger.kernel.org
1506 Proximity measurement indicating that some
1507 object is near the sensor, usually by observing
1511 to SI units is not possible. Higher proximity measurements
1523 Contact: linux-iio@vger.kernel.org
1534 Contact: linux-iio@vger.kernel.org
1536 Unit-less light intensity. Modifiers both and ir indicate
1545 Contact: linux-iio@vger.kernel.org
1559 Contact: linux-iio@vger.kernel.org
1567 Contact: linux-iio@vger.kernel.org
1573 Contact: linux-iio@vger.kernel.org
1585 Contact: linux-iio@vger.kernel.org
1594 Contact: linux-iio@vger.kernel.org
1602 channels refer to the same signal. The 'i' channel contains the in-phase
1611 Contact: linux-iio@vger.kernel.org
1620 Contact: linux-iio@vger.kernel.org
1628 Contact: linux-iio@vger.kernel.org
1636 Contact: linux-iio@vger.kernel.org
1644 Contact: linux-iio@vger.kernel.org
1651 Contact: linux-iio@vger.kernel.org
1661 Non-blocking read will retrieve the available samples from the
1662 buffer even if there are less samples then watermark level. This
1669 Contact: linux-iio@vger.kernel.org
1671 A read-only value indicating the bytes of data available in the
1679 Contact: linux-iio@vger.kernel.org
1681 A read-only boolean value that indicates if the hardware fifo is
1685 current hardware fifo watermark level is set and other current
1690 If the hardware fifo is enabled and the level of the hardware
1691 fifo reaches the hardware fifo watermark level the device will
1703 Contact: linux-iio@vger.kernel.org
1714 Contact: linux-iio@vger.kernel.org
1716 Read-only entry that contains a single integer specifying the
1717 current watermark level for the hardware fifo. If the device
1719 The watermark level for the hardware fifo is set by the driver
1722 buffers are limited to 32-64 samples, some hardware buffers
1728 Contact: linux-iio@vger.kernel.org
1730 A single positive integer specifying the minimum watermark level
1739 Contact: linux-iio@vger.kernel.org
1741 A single positive integer specifying the maximum watermark level
1750 Contact: linux-iio@vger.kernel.org
1760 hardware fifo watermark level.
1767 Contact: linux-iio@vger.kernel.org
1777 Contact: linux-iio@vger.kernel.org
1798 Contact: linux-iio@vger.kernel.org
1808 Contact: linux-iio@vger.kernel.org
1815 Contact: linux-iio@vger.kernel.org
1826 Contact: linux-iio@vger.kernel.org
1829 base-10 logarithm of hydrodium ions in a litre of water.
1837 Contact: linux-iio@vger.kernel.org
1848 way (platform data and / or device-tree), the main hardware
1858 [0, 1, 0; 1, 0, 0; 0, 0, -1]. Identity matrix
1874 An implementor might consider that for a hand-held device, a
1888 front-view camera;
1895 Contact: linux-iio@vger.kernel.org
1902 Contact: linux-iio@vger.kernel.org
1912 Contact: linux-iio@vger.kernel.org
1923 Contact: linux-iio@vger.kernel.org
1929 - "up" : counter device is increasing.
1930 - "down": counter device is decreasing.
1934 Contact: linux-iio@vger.kernel.org
1943 Contact: linux-iio@vger.kernel.org
1952 Contact: linux-iio@vger.kernel.org
1966 Contact: linux-iio@vger.kernel.org
1975 Contact: linux-iio@vger.kernel.org
1978 must be above the threshold level before interrupt is asserted.
1982 Contact: linux-iio@vger.kernel.org
1989 Contact: linux-iio@vger.kernel.org
1996 Contact: linux-iio@vger.kernel.org
2005 Contact: linux-iio@vger.kernel.org
2012 Contact: linux-iio@vger.kernel.org
2023 Contact: linux-iio@vger.kernel.org
2032 Contact: linux-iio@vger.kernel.org
2036 contaminant build-up in a measurement chamber or optical
2047 Contact: linux-iio@vger.kernel.org
2064 Contact: linux-iio@vger.kernel.org
2068 - a range specified as "[min step max]"
2074 Contact: linux-iio@vger.kernel.org
2084 Contact: linux-iio@vger.kernel.org
2091 Contact: linux-iio@vger.kernel.org
2096 Units and the exact meaning of value are device-specific.
2100 Contact: linux-iio@vger.kernel.org
2108 Contact: linux-iio@vger.kernel.org
2113 single-tap's or two double-tap's.
2117 Contact: linux-iio@vger.kernel.org
2123 Contact: linux-iio@vger.kernel.org
2130 Contact: linux-iio@vger.kernel.org
2137 Contact: linux-iio@vger.kernel.org
2145 Contact: linux-iio@vger.kernel.org
2154 Contact: linux-iio@vger.kernel.org
2161 Contact: linux-iio@vger.kernel.org
2163 An example format is 16-bytes, 2-digits-per-byte, HEX-string