61 #  define LOGNAME			"msnd_classic"  macro
65 #  define LOGNAME			"snd_msnd_pinnacle"  macro
124 			snd_printd(KERN_WARNING LOGNAME ": Play underflow %i\n",  in snd_msnd_eval_dsp_msg()
131 			snd_printd(KERN_WARNING LOGNAME ": Record overflow\n");  in snd_msnd_eval_dsp_msg()
136 			snd_printd(KERN_WARNING LOGNAME  in snd_msnd_eval_dsp_msg()
149 		snd_printd(KERN_WARNING LOGNAME ": HIMT message %d 0x%02x\n",  in snd_msnd_eval_dsp_msg()
200 	snd_printk(KERN_ERR LOGNAME ": Cannot reset DSP\n");  in snd_msnd_reset_dsp()
216 		snd_printk(KERN_ERR LOGNAME ": I/O port conflict\n");  in snd_msnd_probe()
228 	printk(KERN_INFO LOGNAME ": %s, "  in snd_msnd_probe()
288 	printk(KERN_INFO LOGNAME ": %s revision %s, Xilinx version %s, "  in snd_msnd_probe()
380 		printk(KERN_ERR LOGNAME ": Error loading " INITCODEFILE);  in upload_dsp_code()
385 		printk(KERN_ERR LOGNAME ": Error loading " PERMCODEFILE);  in upload_dsp_code()
391 		printk(KERN_WARNING LOGNAME ": Error uploading to DSP\n");  in upload_dsp_code()
395 	printk(KERN_INFO LOGNAME ": DSP firmware uploaded\n");  in upload_dsp_code()
428 		printk(KERN_WARNING LOGNAME ": Cannot initialize SMA\n");  in snd_msnd_initialize()
438 		printk(KERN_WARNING LOGNAME ": Cannot upload DSP code\n");  in snd_msnd_initialize()
447 			snd_printd(KERN_ERR LOGNAME ": DSP reset timeout\n");  in snd_msnd_initialize()
469 		printk(KERN_WARNING LOGNAME ": DSP reset failed\n");  in snd_msnd_dsp_full_reset()
504 	printk(KERN_WARNING LOGNAME ": ADC calibration failed\n");  in snd_msnd_calibrate_adc()
538 		printk(KERN_ERR LOGNAME ": Couldn't grab IRQ %d\n", chip->irq);  in snd_msnd_attach()
547 		printk(KERN_ERR LOGNAME  in snd_msnd_attach()
556 		printk(KERN_ERR LOGNAME  in snd_msnd_attach()
574 		printk(KERN_ERR LOGNAME ": error creating new PCM device\n");  in snd_msnd_attach()
580 		printk(KERN_ERR LOGNAME ": error creating new Mixer device\n");  in snd_msnd_attach()
595 			printk(KERN_ERR LOGNAME  in snd_msnd_attach()
645 		printk(KERN_ERR LOGNAME ": snd_msnd_write_cfg: I/O error\n");  in snd_msnd_write_cfg()
734 	printk(KERN_INFO LOGNAME ": Resetting all devices\n");  in snd_msnd_pinnacle_cfg_reset()
815 		printk(KERN_WARNING LOGNAME ": io, irq and mem must be set\n");  in snd_msnd_isa_match()
828 		printk(KERN_ERR LOGNAME ": \"io\" - DSP I/O base must be set "  in snd_msnd_isa_match()
835 		printk(KERN_ERR LOGNAME  in snd_msnd_isa_match()
848 		printk(KERN_ERR LOGNAME  in snd_msnd_isa_match()
859 		printk(KERN_ERR LOGNAME ": \"mem\" - must be set to "  in snd_msnd_isa_match()
867 		printk(KERN_INFO LOGNAME ": Assuming PnP mode\n");  in snd_msnd_isa_match()
869 		printk(KERN_INFO LOGNAME  in snd_msnd_isa_match()
890 		printk(KERN_INFO LOGNAME ": Assuming PnP mode\n");  in snd_msnd_isa_probe()
933 	printk(KERN_INFO LOGNAME ": Non-PnP mode: configuring at port 0x%lx\n",  in snd_msnd_isa_probe()
937 		printk(KERN_ERR LOGNAME ": Config port 0x%lx conflict\n",  in snd_msnd_isa_probe()
961 		printk(KERN_INFO LOGNAME  in snd_msnd_isa_probe()
976 		printk(KERN_INFO LOGNAME  in snd_msnd_isa_probe()
989 		printk(KERN_INFO LOGNAME  in snd_msnd_isa_probe()
1028 		printk(KERN_ERR LOGNAME ": Probe failed\n");  in snd_msnd_isa_probe()
1035 		printk(KERN_ERR LOGNAME ": Attach failed\n");  in snd_msnd_isa_probe()
1153 		printk(KERN_ERR LOGNAME ": Probe failed\n");  in snd_msnd_pnp_detect()
1159 		printk(KERN_ERR LOGNAME ": Attach failed\n");  in snd_msnd_pnp_detect()