Lines Matching +full:flash +full:- +full:leds
1 # SPDX-License-Identifier: GPL-2.0-only
13 LEDs from both userspace and optionally, by kernel events (triggers).
20 This option enables the LED sysfs class in /sys/class/leds. You'll
21 need this to do anything useful with LEDs. If unsure, say Y.
24 tristate "LED Flash Class Support"
27 This option enables the flash LED sysfs class in /sys/class/leds.
28 It wraps LED Class and adds flash LEDs specific sysfs attributes
30 for the flash related features of a LED device. It can be built
37 This option enables the multicolor LED sysfs class in /sys/class/leds.
40 for multicolor LEDs that are grouped together. This class is not
41 intended for single color LEDs. It can be built as a module.
48 for LED sysfs class devices under /sys/class/leds.
50 See Documentation/ABI/testing/sysfs-class-led for details.
59 This option enables support for on-chip LED drivers found on Marvell
66 This option enables support for the AN30259A 3-channel
70 will be called leds-an30259a.
77 This driver makes the PC Engines APU1 front panel LEDs
80 If you're looking for APU2/3, use the pcengines-apu2 driver.
84 module will be called leds-apu.
92 LEDs on Dell Wyse 3020 (Ariel) board via the KB3930 Embedded
101 This option enables support for the AW2013 3-channel
105 will be called leds-aw2013.
113 This option enables support for LEDs connected to the BCM6328
122 This option enables support for LEDs connected to the BCM6358
131 This option enables support for LEDs offered by Motorola's
145 will be called leds-cr0014114.
158 will be called leds-el15203000.
167 This option enables basic support for the LEDs found on the front
168 side of CZ.NIC's Turris Omnia router. There are 12 RGB LEDs on the
197 This option enables support for the LEDs on National Semiconductor /
200 The LEDs can be controlled directly, through PWM input, or by the
201 ambient-light-sensor interface. The chip supports
202 hardware-accelerated blinking with maximum on and off periods of 9.8
210 This option enables support for LEDs connected to LM3642.
211 The LM3642 is a 4MHz fixed-frequency synchronous boost
212 converter plus 1.5A constant current driver for a high-current
228 This option enables support for the LEDs on Sharp Locomo.
229 Zaurus models SL-5500 and SL-5600.
244 This option enables support for on-chip LED drivers found on
248 tristate "LED Support for Samsung S3C24XX GPIO LEDs"
252 This option enables support for LEDs connected to GPIO lines
264 tristate "LED Support for the Freecom FSG-3"
268 This option enables support for the LEDs on the Freecom FSG-3.
271 tristate "LED Support for the WRAP series LEDs"
275 This option enables support for the PCEngines WRAP programmable LEDs.
289 This option enables support for the Cobalt Raq series LEDs.
298 LEDs on the I/O and CPU boards of SunFire UltraSPARC servers.
336 tristate "LED Support for GPIO connected LEDs"
340 This option enables support for the LEDs connected to GPIO
341 outputs. To be useful the particular board must have LEDs
342 and they must be connected to the GPIO lines. The LEDs must be
351 This option enables support for LEDs connected to the National
356 module will be called leds-lp3944.
365 This option enables support for LEDs connected to the Texas
369 module will be called leds-lp3952.
380 module will be called leds-lp50xx.
442 This option enables support for the Keyboard LEDs on the LP8788 PMIC.
451 This option enables support for the display cluster LEDs
461 programs through the leds subsystem. This LED have three
464 The driver supports two kinds of interface: using ledtrig-timer
465 or through /sys/class/leds/clevo::mail/brightness. As this LED
484 module will be called leds-clevo-mail.
491 This option enables support for LEDs connected to PCA955x
511 This option enables support for LEDs connected to the PCA963x
516 tristate "LED support for status LEDs on WM831x PMICs"
520 This option enables support for the status LEDs of the WM831x
528 This option enables support for LEDs driven by the Wolfson
536 This option enables support for on-chip LED drivers found
540 tristate "Dialog DA9052/DA9053 LEDS"
544 This option enables support for on-chip LED drivers found
545 on Dialog Semiconductor DA9052-BC and DA9053-AA/Bx PMICs.
553 which can be used to control up to four LEDs.
560 This option enables support for pwm driven LEDs
567 This option enables support for regulator driven LEDs.
585 drive or power LEDs on the front panel. Using this driver
593 This option enables support for LEDs driven by a Linear Technology
594 LT3593 controller. This controller uses a special one-wire pulse
602 This option enables support for on-chip LED drivers found
606 be called leds-adp5520.
613 This option enables support for on-chip LED drivers found
617 tristate "LED support for Network Space v2 GPIO LEDs"
622 This option enables support for the dual-GPIO LEDs found on the
628 n090401 (Seagate NAS 4-Bay)
631 tristate "LED support for Big Network series LEDs"
637 This option enables support for LEDs found on the LaCie 2Big
638 and 5Big Network v2 boards. The LEDs are wired to a CPLD and are
647 This option enables support for the LEDs on the HTC ASIC3. The HTC
648 ASIC3 LED GPIOs are inputs, not outputs, thus the leds-gpio driver
650 period from 62ms to 125s. Say Y to enable LEDs on the HP iPAQ hx4700.
656 This option enables support for LEDs connected to TC6507
658 Driver support brightness control and hardware-assisted blinking.
672 LEDs driver for MAX77650 family of PMICs from Maxim Integrated.
678 This option enables support for on-chip LED drivers on
686 This option enables support for LEDs connected to LM3554
687 and LM3556. It includes Torch, Flash and Indicator functions.
693 This option enables support for the LEDs on the Bachmann OT200.
694 Say Y to enable LEDs on the Bachmann OT200.
700 Say Y here to include support for the MEN 14F021P00 BMC LEDs.
703 will be called leds-menf21bmc.
710 This option enables support for LEDs connected to ISSI IS31FL319x
715 called leds-is31fl319x.
721 Say Y here to include support for ISSI IS31FL32XX and Si-En SN32xx
722 LED controllers. They are I2C devices with multiple constant-current
723 channels, each with independent 256-level PWM control.
731 LEDs.
734 called leds-sc27xx-bltc.
752 This option enables support for the system LEDs present on
755 will be called leds-powernv.
758 bool "LED support for LEDs on system controllers"
763 This option enables support for the LEDs on syscon type
780 This option enables support for the LEDs on the Mellanox
787 This option enables support for the LEDs on the Mellanox Ethernet and
790 module, choose 'M' here: the module will be called leds-mlxreg.
796 This option enables support for userspace LEDs. Say 'y' to enable this
805 This option enables support for the User1 and User2 LEDs on NI
809 will be called leds-nic78bx.
853 It is a single boost converter primarily for white LEDs and
861 This option enables support for the Red and White LEDs of
865 will be called leds-ip30.
874 source "drivers/leds/blink/Kconfig"
876 comment "Flash and Torch LED drivers"
877 source "drivers/leds/flash/Kconfig"
880 source "drivers/leds/trigger/Kconfig"