Lines Matching +full:non +full:- +full:removable

1 // SPDX-License-Identifier: GPL-2.0
2 /dts-v1/;
5 #include <dt-bindings/gpio/gpio.h>
6 #include <dt-bindings/clock/ingenic,sysost.h>
7 #include <dt-bindings/interrupt-controller/irq.h>
10 	compatible = "yna,cu1830-neo", "ingenic,x1830";
11 	model = "YSH & ATIL General Board CU1830-Neo";
18 		stdout-path = "serial1:115200n8";
27 		compatible = "gpio-leds";
28 		led-0 {
30 			linux,default-trigger = "mmc0";
34 	ssi0: spi-gpio {
35 		compatible = "spi-gpio";
36 		#address-cells = <1>;
37 		#size-cells = <0>;
38 		num-chipselects = <1>;
40 		mosi-gpios = <&gpc 12 GPIO_ACTIVE_HIGH>;
41 		miso-gpios = <&gpc 11 GPIO_ACTIVE_HIGH>;
42 		sck-gpios = <&gpc 15 GPIO_ACTIVE_HIGH>;
43 		cs-gpios = <&gpc 16 GPIO_ACTIVE_HIGH>;
47 		spi-max-frequency = <50000000>;
52 			spi-max-frequency = <4000000>;
56 			interrupt-parent = <&gpb>;
59 			gpio-controller;
60 			#gpio-cells = <2>;
63 				compatible = "fixed-clock";
64 				#clock-cells = <0>;
65 				clock-frequency = <48000000>;
70 	wlan_pwrseq: msc1-pwrseq {
71 		compatible = "mmc-pwrseq-simple";
73 		reset-gpios = <&gpc 13 GPIO_ACTIVE_LOW>;
74 		post-power-on-delay-ms = <200>;
79 	clock-frequency = <24000000>;
87 	assigned-clocks = <&cgu X1830_CLK_RTC>;
88 	assigned-clock-parents = <&cgu X1830_CLK_RTCLK>;
93 	assigned-clocks = <&ost OST_CLK_PERCPU_TIMER>, <&ost OST_CLK_GLOBAL_TIMER>;
94 	assigned-clock-rates = <1500000>, <1500000>;
100 	pinctrl-names = "default";
101 	pinctrl-0 = <&pins_uart1>;
107 	clock-frequency = <400000>;
109 	pinctrl-names = "default";
110 	pinctrl-0 = <&pins_i2c0>;
125 	bus-width = <4>;
126 	max-frequency = <50000000>;
128 	pinctrl-names = "default";
129 	pinctrl-0 = <&pins_msc0>;
131 	non-removable;
137 	#address-cells = <1>;
138 	#size-cells = <0>;
139 	bus-width = <4>;
140 	max-frequency = <50000000>;
142 	pinctrl-names = "default";
143 	pinctrl-0 = <&pins_msc1>;
145 	non-removable;
147 	mmc-pwrseq = <&wlan_pwrseq>;
150 		compatible = "brcm,bcm4329-fmac";
153 		interrupt-parent = <&gpc>;
155 		interrupt-names = "host-wake";
157 		brcm,drive-strength = <10>;
164 	phy-mode = "rmii";
165 	phy-handle = <&ip101gr>;
167 	pinctrl-names = "default";
168 	pinctrl-0 = <&pins_mac>;
170 	snps,reset-gpio = <&gpb 28 GPIO_ACTIVE_LOW>; /* PB28 */
171 	snps,reset-active-low;
172 	snps,reset-delays-us = <0 10000 30000>;
178 	ip101gr: ethernet-phy@0 {
179 		compatible = "ethernet-phy-id0243.0c54", "ethernet-phy-ieee802.3-c22";
195 		groups = "uart1-data";
196 		bias-pull-up;
201 		groups = "i2c0-data";
202 		bias-pull-up;
207 		groups = "mmc0-1bit", "mmc0-4bit";
208 		bias-disable;
213 		groups = "mmc1-1bit", "mmc1-4bit";
214 		bias-disable;
220 		bias-disable;