Lines Matching +full:non +full:- +full:removable

1 // SPDX-License-Identifier: GPL-2.0
2 /dts-v1/;
5 #include <dt-bindings/gpio/gpio.h>
6 #include <dt-bindings/clock/ingenic,sysost.h>
7 #include <dt-bindings/interrupt-controller/irq.h>
10 	compatible = "yna,cu1000-neo", "ingenic,x1000e";
11 	model = "YSH & ATIL General Board CU1000-Neo";
18 		stdout-path = "serial2:115200n8";
27 		compatible = "gpio-leds";
28 		led-0 {
30 			linux,default-trigger = "mmc0";
34 	ssi: spi-gpio {
35 		compatible = "spi-gpio";
36 		#address-cells = <1>;
37 		#size-cells = <0>;
38 		num-chipselects = <1>;
40 		mosi-gpios = <&gpd 2 GPIO_ACTIVE_HIGH>;
41 		miso-gpios = <&gpd 3 GPIO_ACTIVE_HIGH>;
42 		sck-gpios = <&gpd 0 GPIO_ACTIVE_HIGH>;
43 		cs-gpios = <&gpd 1 GPIO_ACTIVE_HIGH>;
47 		spi-max-frequency = <50000000>;
52 			spi-max-frequency = <4000000>;
56 			interrupt-parent = <&gpc>;
59 			gpio-controller;
60 			#gpio-cells = <2>;
63 				compatible = "fixed-clock";
64 				#clock-cells = <0>;
65 				clock-frequency = <48000000>;
70 	wlan_pwrseq: msc1-pwrseq {
71 		compatible = "mmc-pwrseq-simple";
73 		reset-gpios = <&gpc 17 GPIO_ACTIVE_LOW>;
74 		post-power-on-delay-ms = <200>;
79 	clock-frequency = <24000000>;
87 	assigned-clocks = <&cgu X1000_CLK_RTC>;
88 	assigned-clock-parents = <&cgu X1000_CLK_RTCLK>;
93 	assigned-clocks = <&ost OST_CLK_PERCPU_TIMER>, <&ost OST_CLK_GLOBAL_TIMER>;
94 	assigned-clock-rates = <1500000>, <1500000>;
100 	pinctrl-names = "default";
101 	pinctrl-0 = <&pins_uart2>;
107 	clock-frequency = <400000>;
109 	pinctrl-names = "default";
110 	pinctrl-0 = <&pins_i2c0>;
121 	bus-width = <8>;
122 	max-frequency = <50000000>;
124 	pinctrl-names = "default";
125 	pinctrl-0 = <&pins_msc0>;
127 	non-removable;
133 	#address-cells = <1>;
134 	#size-cells = <0>;
135 	bus-width = <4>;
136 	max-frequency = <50000000>;
138 	pinctrl-names = "default";
139 	pinctrl-0 = <&pins_msc1>;
141 	non-removable;
143 	mmc-pwrseq = <&wlan_pwrseq>;
146 		compatible = "brcm,bcm4329-fmac";
149 		interrupt-parent = <&gpc>;
151 		interrupt-names = "host-wake";
153 		brcm,drive-strength = <10>;
160 	phy-mode = "rmii";
161 	phy-handle = <&lan8720a>;
163 	pinctrl-names = "default";
164 	pinctrl-0 = <&pins_mac>;
166 	snps,reset-gpio = <&gpc 23 GPIO_ACTIVE_LOW>; /* PC23 */
167 	snps,reset-active-low;
168 	snps,reset-delays-us = <0 10000 30000>;
174 	lan8720a: ethernet-phy@0 {
175 		compatible = "ethernet-phy-id0007.c0f0", "ethernet-phy-ieee802.3-c22";
191 		groups = "uart2-data-d";
192 		bias-pull-up;
197 		groups = "i2c0-data";
198 		bias-pull-up;
203 		groups = "mmc0-1bit", "mmc0-4bit", "mmc0-8bit";
204 		bias-disable;
209 		groups = "mmc1-1bit", "mmc1-4bit";
210 		bias-disable;
216 		bias-disable;